PARTS AND SERVICE MANUAL FOR DIMPLEX 23” OUTDOOR ELECTRIC FIREPLACE Model DFO2307
TABLE OF CONTENTS OPERATION PAGE 2 PARTS DRAWING PAGE 3 PARTS LIST PAGE 4 WIRING DIAGRAM PAGE 5 FRONT GLASS REMOVAL PAGE 6 UPPER LIGHT REPLACEMENT PAGE 7 LOWER LIGHT REPLACEMENT PAGE 8 MAIN ON/OFF REPLACEMENT PAGE 9 FLAME ROD AND MOTOR REPLACEMENT PAGE 10 CIRCUIT BOARD REPLACEMENT PAGE 11 1
DFO2307 OPERATION ELECTRIC FIREPLACE MANUAL CONTROL The manual controls for the firebox are located in the upper right hand corner behind the access panel. To access the controls, open the upper access panel by pulling forward and down. To locate controls refer to Figure 3. A. Main On/Off Switch The ON/OFF SWITCH supplies power to the flames and over head lights. NOTE: This unit does not have a heat option.
5 4 2 6 10 3 7 1 9 8 11 3
DFO2307 REPLACEMENT PARTS FIREBOX, 23” – Dimplex CATALOGUE NO. PART NO. DFO2307 6903100100 REPLACEMENT PART 1. MOTOR, ASSEMBLY 2. LED LIGHT, 1 WATT 3. ON/OFF SWITCH 4. CIRCUIT BOARD 5. MIRROR 6. GLASS FRONT 7. LED LIGHT, BOTTOM 8. TRANSFORMER 9. FLAME ROD 10. BUSHING 11.
1 WATT LED FLAME LIGHT + LIGHT WIRE HARNESS + 5 3 WATT LED FLAME LIGHT - 1 WATT LED TOP LIGHT + INCLUDED IN LIGHT WIRE HARNESS "A" TERMINAL (HARNESS INCLUDED) FLICKER MOTOR 1 WATT LED FLAME LIGHT YELLOW WIRE OF CABLE TO LINE UP WITH SQUARE SOLDER PAD OF CONNECTOR ON BOARD. SQUARE SOLDER PAD (BACK SIDE VIEW) CONNECTOR, WIRE TWISTER MAIN PCB BOARD MAIN ON/OFF SWITCH "A" TERMINAL "B" TERMINAL TYP. CONNECTOR, FEMALE (HARNESS INCLUDED) THIS END TO BE CONNECTED TO TRANSFORMER.
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. FRONT GLASS REMOVAL 1. 2. 3. 4. 5. Remove top from mantel. Lift firebox out of mantel. Lay firebox on it’s back. Remove screws from the left and right side of the front glass lower support. Insert the tip of a slot screwdriver between the glass edge on either the left or right side trim. 6.
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. It is a good idea to replace all of the lights at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace the lights. UPPER LIGHT REPLACEMENT 1. 2. 3. 4. 5. 6. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws.
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Lights need to be replaced when you notice a dark section of the flame. There are three lights under the log set which generate the flames and embers located under the emberbed. It is a good idea to replace all of the lights at one time if they are close to the end of their rated life.
DFO2307 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. MAIN ON/OFF SWITCH REPLACEMENT 1. 2. 3. 4. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws. Remove the 10 retaining screws and lift the top off of the unit. Locate the main on/off switch mounted on the top panel and disconnect the wiring clips and connections noting their original locations. 5.
DFO2307 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. FLAME ROD AND MOTOR REPLACEMENT 1. 2. 3. 1. 4. 5. 6. 7. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws.
DFO2307 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD 1. 2. 3. 4. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws. Remove the 10 retaining screws and lift the top off of the unit.
