Technical data

www.dimplex.de/en
29
2012
Design built-under domestic hot water cylinder
WWSP 229E
Nominal capacity 227 l, in brine-to-water heat pump design to enable space-saving installation on the built-under domestic hot water
cylinder, bare-tube heat exchanger (internal), steel cylinder (special inside enamelling) with protection anode, polyurethane insulation
with minimum standby losses; integrated temperature sensor for connection to the heat pump manager, colour: white, brown red
design screen.
Permissible operating pressure 10 bar; Flange TK150/DN110 ;
Order reference Art.-no. For
device
type
Usable
capacity
l
Heat ex-
change
surface
m²
Con-
nection
heating
˝
Con-
nection
circula-
tion
˝
Connection
DHW
˝
Width x Height x
Depth
mm
Weight
kg
WWSP 229E 353380
Up to
SI(K) 9
206 2.9 1¼ ¾ 1 650 x 1040 x 680 110
Recommended for service areas without shut-off times or with reduced domestic hot water consumption.
The achievable hot water temperatures are dependent on the maximum heat output of the heat pump, the heat exchange surface and the volume
flow in the load circuit (dimensioned for max. hot water temperatures of 45 °C according to the project planning documentation). For heat pumps
with two performance levels, domestic hot water preparation is achieved with a compressor.
WWSP 229E 353380 4015627353381
Heat pump for heating purposes - ground as heat source
Compact brine-to-water heat pump connection kit
VSH KS
VSW KS
VS PKS
VSW 229
Order reference Art.-no. For device type Short text Features
VSH KS 343110
SIK ..
Heating ‚
connection kit
Hose kit for easy connection of the compact brine-to-
water heat pump and built-under buffer tank to the
heating system (minimum distance from wall 20 cm).
Consists of four elbow unions with three manual
breathers, buffer connection with filling and drain cock
and two corrugated stainless steel pipes with high-and-
low temperature insulation. 1“ internal thread connec-
tion to the heating system.
VSW KS 343120
VSH KS with WWSP
Domestic
hot water
expansion kit
Domestic hot water extension hose kit for using the
heating connection kit (VSH KS) in addition to the
domestic hot water cylinder and a circulating pump.
Consists of 3 elbow unions with 2 manual breathers,
1 T joint, pump shut-offs for the domestic hot water
circulating pump (pump not included in the scope of
supply) and 2 corrugated stainless steel pipes with high
and low temperature insulation.
VS PKS 348630
VSH KS with PKS
Extension
hose kit for
passive cooling
station
Passive cooling station extension hose kit, to enable the
use of the heating connection kit (VSH KS) in addition to
the heating and brine circuit connection of the passive
cooling station PKS 14, situated on the compact brine-
to-water heat pump. Consists of 2 elbow unions with
manual breather, crosspiece and 4 corrugated stainless
steel pipes with high and low temperature insulation.
VSW 229 356050
SIK with WWSP 229E
Connection kit,
domestic
hot water
Hose set for easy connection of the compact brine-
to-water heat pump and the built-under domestic
hot water cylinder to the heating system. Consists of
2 corrugated stainless steel tubes with high and low
temperature insulation, 2 elbow unions with manual
breather and an installation option for the domestic
hot water circulating pump (pump not included in the
scope of supply).
VSH KS 343110 4015627343115
VSW KS 343120 4015627343122
VS PKS 348630 4015627348639
VSW 229 356050 4015627356054