INSTRUCTION MANUAL Laverton 2kW Electric Stove Model: LVT20-AU For domestic household use only.
IMPORTANT THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE. CAUTION: FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE INJURY AND/ OR DAMAGE AND MAY INVALIDATE YOUR WARRANTY Please read the operating instructions carefully before using your product for the first time and keep them in a safe place.
• Although this appliance complies with safety standards, we do not recommend its use on deep pile carpets or on long hair type of rugs • The appliance must be positioned so that the plug is accessible. • If the supply cord is damaged it must be replaced by the manufacturer or service agent or a similarly qualified person in order to avoid a hazard. • Keep the supply cord away from the front of the appliance.
WARNING: KEEP BATTERIES OUT OF REACH OF CHILDREN • Swallowing may lead to serious injury in as little as 2 hours or death, due to chemical burns and potential perforation of the oesophagus. • If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Information Centre on 13 11 26 (in Australia) or 0800 764 766 (in New Zealand) for fast, expert advice. • Examine devices and make sure the battery compartment is correctly secured, e.g.
Exposed to the weather outdoors Near water If the power cable wires are frayed or cut Where small children may be left unattended No extension leads or power boards Where the power cable may be damaged On a slope or uneven surface Where there is risk of fire or close to a naked flame Where it may be damaged by chemicals Where there is a risk of interference by foreign objects This product is not made for DIY repair If there is a risk of water falling on the unit 5
Specifications Model no. LVT20-AU Colour/Finish Black Wattage 2000 Heat Settings 2 Thermostat Control Yes LED effect Yes Remote Control Yes Warranty Dimensions (w x d x h) 2 Years 444w x 340d x 680h For greater precision, please always refer to the rating label placed on the product. Product Dimensions Laverton LVT20-AU 6 Fig.
Setup General Information The fire incorporates a flame effect, which can be used with or without heat, so that the comforting effect may be enjoyed at any time of the year. To reduce heat loss and to prevent any chimney up draft affecting the operation of your stove fire, we recommend that the chimney flue is sealed off. Always ensure that the appliance is sitting on a level surface. Before connecting the appliance, check that the supply voltage is the same as that stated on the appliance.
Fuel Bed Assembly Your fire has been supplied with a range of fuel bed material’s, all models contain a 5-piece log set together with a loose set of crystals and vermiculite pieces to complete the fire effect. See Fig.2 below Note: Each log has a number engraved on the surface to help with identification. Fig. 2 1 2 Decorative Crystals (130g) 3 4 5 Vermiculite (Ash) (50g) Warning: Choking may be caused by swallowing small loose fuel bed media (crystal, vermiculite) accidentally.
Fuel Bed Assembly Step 1 Fig. 3 1 2 Step 2 1 5 4 3 2 Step 3 1 5 4 3 2 Between logs 3 & 4 sweep the vermiculite apart to clearly expose the underlying fuel bed base in the three circle marked areas shown above.
Fuel Bed Assembly Step 4 Using the 130g bag of crystals supplied, first place some crystals into the three clear fuel bed circles created in step 3, fill the exposed fuel bed area fully with crystals as shown. The remainder of the crystals can then be placed anywhere else on the fuel bed. These crystals are used to generate the illusion of hot ash and fire embers. We recommend using the entire bag of crystals to achieve optimal effect.
Control Panel & Remote WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN INJURY AND/OR DAMAGE. NOTE: The Remote Control is packaged in a red box. The battery is also stored in this box and must be installed in the remote control before operation. CAUTION: The remote handset requires a button cell battery (CR2032) to operate. This is supplied in a small zip bag with the handset. Fig. 4 Remote 1. Locate the battery compartment on the back of the handset. 2.
Operation Operating Instructions (Remote)- See Figure 4 Display A - Function Power / Standby F1 / F2 / F3 P Flame Pulsing Sleep Timer C Press Once to turn the product ‘ON’. ss a second time to put p the product into ‘STANDBY’. Red indicator light will show Press upon display for 10 seconds.
Operation Operating Instructions (Controls)- See Figure 5 Icon Description 1 Press Once to turn the product ‘ON’. Press a second time to put the product into ‘STANDBY’ (When returning from ‘STANDBY’ mode the product will return to previous settings unless the product has been unplugged, in which case it will reset to factory settings) 2 ‘FLAME EFFECT’ button this button will cycle through the settings ‘F0’, ‘F1’, ‘F2’, ‘F3’, ‘P’. 3 Press to turn ON/OFF the Top light illuminating the fuel bed.
Cleaning Over time, dust can accumulate which can effect performance. It is recommended to clean the unit at least once a month. CAUTION: ALWAYS Turn the unit OFF and disconnect the appliance from the power supply before undergoing any cleaning and maintenance. The surfaces of the heater should be given an occasional wipe with a dry soft cloth. Do not use detergents, abrasive cleaning powder or furniture polish as this can damage the surface of the product.
Customer Care: 1300 556 816 customer.care@glendimplex.com.au www.dimplex.com.au Supplied by Glen Dimplex Australia 8 Lakeview Drive, Scoresby, Victoria, 3179 © Glen Dimplex Australia. All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Glen Dimplex Australia.
