Product Manual

ManualsBrandsDimplex ManualsElectric HeatersWall Mounted Electric Fire Heater

Webcopy July2015

LightBulbs–Howtochange

Optiflame/Opti‐myst/RadiantBar



Optiflame–Insets



Adagio

Aspen

Danesbury

Delius

Elda

Horton

Wynford

Whitsbury

Siva



Therearetwolampslocatedbeneaththefueleffect.Togainaccess

tothelamps,thegrate/fueleffectsecuredbytwoscrewsmustbe

removed.

Removethecoal/pebblesandplaceinacontainerandcarefully

lift

thegrate/fueleffectclearandsetaside.

Replacethedefectivelampwitha240V‐60WE14SESclearcandle

lamp.

Replacegrate/fueleffect,securewithscrewsandaddcoal/pebbles.



Optiflame–Insets



Kansas

Dakota

Inver



Togainaccesstothelampremovethefret,pebbles/coalandfuel

effectfromthefire.Placepebblesorcoalinacontainer.Remove

thefretbyliftingitupandthenpullingitoutfromthefire,then

removethefixingscrews

fromthefuelbedandslidingoutthefuel

effect.Removetherotisseriebycarefullyslidingtherubber

connecteroffthemotorshaft.Re movethedefectivelampby

unscrewingit.Replacewitha60WE14SESClearCandlelamp.Take

carenottoovertightenthelamp.Refitthefretand

fueleffect.Then

placepebblesandcoalbackonfueleffect.



Optiflame–Insets



Exbury

Loxley

X1



Therearetwolampslocatedbeneaththefueleffect.Togainaccess

tothelamps,removethecoal/pebblesandplaceinacontainer.

Removethefueleffectfromthefirebyliftingitupandoutfromthe

slotsonthefire.

Removethe

defectivelampbyunscrewingit.

Replacewitha60WE14SESClearCandlelamp.Takecarenotto

overtightenthelamp.

Refitthefueleffectandreplacethecoal/pebbles.



Optiflame–Insets



Clement



Therearetwolampslocatedbeneaththefueleffect.Togainaccess

tothelamps,removethefrontfret/fueleffectfromthefirebylifting

itupandoutfromtheslotsonthefire.Removetherotisserieby

carefullyslidingtherubberconnecteroffthe

motorshaft.Remove

thedefectivelampbyunscrewingit.Replacewitha60WE14SES

ClearCandlelamp.Takecarenottoovertightenthelamp.Refitthe

frontfret/fueleffect.



Summary of content (4 pages)

PAGE 1
Light Bulbs – How to change Optiflame / Opti‐myst / Radiant Bar Optiflame – Insets Adagio Aspen Danesbury Delius Elda Horton Wynford Whitsbury Siva There are two lamps located beneath the fuel effect. To gain access to the lamps, the grate / fuel effect secured by two screws must be removed. Remove the coal/pebbles and place in a container and carefully lift the grate / fuel effect clear and set aside. Replace the defective lamp with a 240V ‐ 60W E14 SES clear candle lamp.
PAGE 2
Optiflame – Freestanding Castillo Cheriton Detroit Zamora Optiflame – MicroFire/ Stove MicroFire MicroStove There are two lamps located beneath the fuel effect. To gain access to the lamps, remove the coals and place in a Container. Remove the two screws from the grate and lift out the plastic fuel effect and grate assembly to reveal the lamp. Remove the rotisserie by carefully sliding the rubber connecter off the motor shaft. Replace the defective lamp with a 240V 60W E14 SES candle lamp.
PAGE 3
Optiflame – Wall Mounted SP16 Lamp Replacement WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY BEFORE REMOVING LAMPS. Warning ‐ The lamps reach high temperatures during operation. For this reason, allow the lamps to cool down after switching off the appliance. The front panel will need to be removed in order to change lamps. Warning ‐ The front panel is heavy and easily damaged. The front panel is supported at the top by two brackets and held tight by magnets at the bottom.
PAGE 4
Opti‐myst Fires All Models If the smoke appears grey or colourless it may be that one or more lamps have failed. You can check for lamp failure as follows. 1. Leaving the flame effect on, lift out the fuelbed and water tank. 2. It should be possible to view the lamps with the nozzle in place and observe which one needs to be changed. 3. Switch the fire to the ‘OFF’ position, and unplug the fire from the mains. 4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them. 5.