RETAIL OPTIMYST WALL ENGINE RTOPW20 08/51917/0 Issue 3 The product complies with the European Safety Standards EN60335-2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014, EN60555-2 and EN60555-3 These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
Fig.1 Fig.2 Fig.4 Fig.3 Fig.
Fig.6 Fig.5 Fig.6a Fig.8 Fig.7 Fig.
Fig.10 Fig.11 Fig.
Dimplex Opti-myst wall Fire Model: RTOPW20 IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE Important Safety Advice: When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following: If the appliance is damaged, check with the supplier before installation and operation. Do not use outdoors.
2. Fix the wall bracket to the wall making sure it is level, using the wall plugs and screws supplied for block walls. 3. Hang the appliance off the fixed wall bracket. Rotate the safety fixing bracket on the base of the product so that the fixing hole is exposed. Mark this hole and remove the appliance from the wall. Fix plug to the wall in the marked position. 4. Hang the appliance back on the wall fixing bracket and fix the appliance in place using the screw supplied through the safety fixing bracket.
2. View the lamps from a distance in front of the fire and observe which lamp needs to be changed. 3. Press switch ‘A’ to off (0) position (See Fig.2), and unplug the fire from the mains. 4. Leave the appliance for 20 minutes to allow the lamps to cool down before removing them. 5. Remove the water tank by lifting upwards and place in a sink. 6. Remove the sump as described in the Cleaning Section. 7.
Remote Control Operation On the control panel, Switch A (see Fig.2) must be in the ‘ON’ ( I ) position in order for the remote control to operate. There are 3 buttons on the remote control. (See Fig.7) To operate correctly the remote handset must be pointed towards the heater outlet. (See Fig 12). The remote control functions are as follows: Press once to turn on Flame effect only. This will be indicated by one beep. Press once to turn on Half heat and Flame effect. This will be indicated by two beeps.
Patent / Patent Application Products within the Optimyst range are protected by one or more of the following patents and patent applications: Great Britain GB 2402206, GB 2460259, GB 2460453 , GB 2418014, GB 2465738, GB 2449925, GB 2465537 , GB 2455277 , GB1020534.2, GB1020537.5, GB1110987.3 United States US 7967690, US 2010299980, US 2011062250, US 2008028648, US 13/167,042 Russia RU2008140317 European EP 2029941, EP 2201301, EP 2315976, EP 1787063, EP07723217.1 , EP11170434.2, EP 11170435.
Troubleshooting Symptom Cause Corrective Action The flame effect will not start. Mains plug is not plugged in. Check plug is connected to wall socket correctly. Low water level. Check that the water tank is full and there is water in the sump. Low voltage connector not connected properly. Check that the connector is inserted correctly. (See Fig.6) (See Fig.6) The flame effect is too low.
Opti-myst is a trade mark of GDC Group Ltd. DIMPLEX MILLBROOK HOUSE GRANGE DRIVE HEDGE END SOUTHAMPTON TEL: 0844 879 3588 FAX: 0844 879 3583 WEBSITE: www.dimplex.co.uk Republic of Ireland Tel. 01 8424833 SO30 2DF [c] GDC Group Ltd, All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex.
