MODEL SF3202 SERVICE MANUAL 7400670000R02
Contents OPERATION ............................................................................................................................. 2 REMOTE CONTROL OPERATION ....................................................................................... 3 REPLACEMENT PARTS ........................................................................................................... 7 WIRING DIAGRAM ...........................................................................................................
SF3202 OPERATION Electric Fireplace Manual Controls A. Manual on/off switch 1. The fireplace has a manual power ON/OFF switch located on the control panel of the fireplace. 2. To operate press the switch once, to turn the unit on. A red light will illuminate to indicate the power is on. Press the switch again to turn the unit off. NOTE: When the manual power switch is used the heater will run. The manual ON/OFF switch is to be used only when the remote transmitter is OFF. B.
SF3202 REMOTE CONTROL OPERATION Initializing the Remote Control 1. Turn on the electrical power at the circuit breaker. 2. Slide open the battery cover on the back of the remote transmitter. 3. Install three AAA batteries into the remote control. Replace the battery cover. Note: The LCD display will flash when new batteries are inserted. 4. Move the remote transmitter close to the fireplace (less than five feet preferred). Press any button on the remote control.
SF3202 Timer Mode 1. You can set the timer to the length of time you want the unit to operate 2. (1 to 120 minutes). 3. Press the TIMER button once. The timer display will blink --4. Press the UP and DOWN buttons to adjust the timer display in minutes. 5. Press the TIMER button once to set the timer. 6. The timer setting can be reset by pressing the TIMER button and using the DOWN button until the timer display reads ----, press the TIMER button once to set the timer. 7.
SF3202 5
SF3202 18 15 8 2 14 9 7 5 7 12 6 10 17 13 1 6
SF3202 REPLACEMENT PARTS FIREPLACE 32” - SYMPHONY CATALOGUE NO. PART NO. MOD LEVEL: MADE IN: SF3202 6901340159 A CANADA SF3202 6901340159 B CANADA REPLACEMENT PART REPLACEMENT PART NO. 1. LOG SET 0438550100RP 0438550100RP 2. HEATER ASSEMBLY 2000230100RP 2000230100RP 3. LOWER LIGHT HARNESS 2500190500RP 2500190500RP 4. UPPER LAMPHOLDER ASSEMBLY 4200120900RP 2500200100RP 5. HEATER ON/OFF SWITCH 2800070200RP 2800070700RP 6. CIRCUIT BOARD 3000210100RP 3000210100RP 7.
SF3202 WIRING DIAGRAM 8
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are four bulbs under the log set which generate the flames and embers.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Light bulbs need to be replaced when you notice a dark section of the flame. There are four bulbs under the log set which generate the flames and embers.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE LED/SWITCH HARNESS 1. Remove the firebox from the back of the mantel. 2. Remove the retaining screws on the top cover and remove the top being careful not to damage any of the wiring. 3.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME SPEED CONTROL 1. Remove the firebox from the back of the mantel. 2. Remove the retaining screws on the top panel and remove the top being careful not to damage any of the wiring. 3.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE FLAME MOTOR/FLAME ROD 1. Remove the log set by lifting up the front edge of the log until it clears the front tabs. Pull out until the rear tab clears the back ledge, then lift out. 2.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATER ON/OFF SWITCH 1. Remove the firebox from the back of the mantel. 2. Remove the retaining screws on the top panel and remove the top being careful not to damage any of the wiring. 3.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE HEATER ASSEMBLY 1. Remove the firebox from the back of the mantel. 2. Remove the retaining screws on the top panel and remove the top being careful not to damage any of the wiring. 3.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD 1. Remove the firebox from the back of the mantel. 2. Remove the retaining screws on the top panel and remove the top being careful not to damage any of the wiring. 3.
SF3202 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE POWER CORD 1. Remove the firebox from the back of the mantel. 2. Remove the retaining screws on the top panel and remove the top being careful not to damage any of the wiring. 3.
SF3202 TROUBLESHOOTING GUIDE GENERAL Problem Cause Solution Improper circuit current rating Additional appliances may exceed the current rating of the circuit breaker or fuse.
SF3202 TROUBLESHOOTING GUIDE HEATER Problem Heater is not turning off Heater is not turning on Cause Solution Service Manual Reference Defective heater on/off switch Replace heater on/off switch Page 13 Improper operation See User’s Guide Loose wiring Trace wiring in unit Page 7 Defective heater on/off switch Replace heater on/off switch Page 13 Defective heater assembly Replace heater assembly Page 14 Improper operation See User’s Guide Loose wiring Trace wiring in unit Normal opera
SF3202 TROUBLESHOOTING GUIDE HEATER (CONTINUED) Problem Heater fan runs continuously Cause Solution Service Manual Reference Loose wiring Trace wiring in unit Page 7 Defective heater on/off switch Replace heater on/off switch Page 13 Defective heater assembly Replace heater assembly Page 14 Cause Solution Service Manual Reference Dirty blower assembly Clean blower assembly Defective blower assembly Replace heater assembly Page 14 Moving flame rod hitting or rubbing against internal co
