Models XLF50 XLF60 XLF74 XLF100 Installation and User’s Guide We value your feedback! Your input helps to create even better products and experiences. Share the warmth and leave a review. dimplex.com/sharethewarmth IMPORTANT SAFETY INFORMATION: Read this manual first before attempting to install or use this electric fireplace. Always comply with the warnings and safety instructions contained in this manual to prevent personal injury or property damage.
Table of Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORTANT INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Welcome Thank you and congratulations for choosing to purchase a Dimplex fireplace. Please carefully read and save these instructions. WARNING: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty. Please record your model and serial numbers for future reference. Model and serial numbers can be found on the label located behind the front glass of your fireplace.
IMPORTANT INSTRUCTIONS When using any electrical appliance, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons. These precautions include: ① Read all instructions before using this electric fireplace. ② This fireplace is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation.
IMPORTANT INSTRUCTIONS WARNING: Remote control contains small batteries. Keep away from children. If swallowed, seek medical attention immediately. Do not install battery backwards, charge, put in fire or mix with used or other battery types may explode or leak causing injury. CALIFORNIA PROPOSITION 65 WARNING: This product can expose you to chemicals including nickel which is known to the State of California to cause cancer. For more information, visit www.P65Warnings.ca.
Technical Specifications Electrical Rating Voltage: 120 V (3-Wire) or 240 V (4-Wire) Power: 1500 W at 120 V, 2500 W at 240 V UL Listing File Number: E71416 Model Reference XLF50 690963XXXX XLF60 691000XXXX XLF74 690969XXXX XLF100 690970XXXX *XXXX indicates a non-safety critical suffix. Product Dimensions Figure 1 1 Figure 15.00 in. 381 mm XLF50 51.41 in [1306 mm] XLF60 61.41 in [1560 mm] XLF74 75.41 in [1916 mm] XLF100 101.41 in [2576 mm] 6 15.82 in. 402 mm 50.31 in [1278 mm] 60.
Package Contents Image Quantity Description XLF50 XLF60 XLF74 XLF100 Remote Control 1 1 1 1 Bag of Medium Acrylic Crystals 3 4 5 6 Large Acrylic Crystals 12 14 18 24 Firebox 1 1 1 1 Front Glass 1 1 1 1 Hex Key 1 1 1 1 Black Screws (M4X10, button head) 2 2 4 4 Screw Covers 2 2 4 4 Mirrored Glass 1 1 1 1 Power Cord 1 1 1 1 7
Package Contents Image Quantity Description XLF50 XLF60 XLF74 XLF100 User’s and Installation Guide 1 1 1 1 Suction Cup 0 1 1 1 1 1/2" Wood Screws 4 4 4 4 Bubble Level 1 1 1 1 Twist-on Wire Connectors 4 4 4 4 Wire Ties 2 2 2 2 Do not dispose of the suction cup after installation. Keep it in a secure location as it will be helpful for maintenance and service of the unit. *Package contents are subject to change 8 www.dimplex.
Installation Placement ! NOTE: It is recommended that the bottom of the unit be mounted between 5" (13 cm) and 40" (102 cm) from the ground to maintain an optimized viewing angle of the flame. WARNING: The top of the fireplace must be installed a minimum of 24" (61 cm) from the ceiling. The fireplace must be installed a minimum of 5" (13 cm) from the ground. Installation in a Bathroom If this unit is installed in a bathroom, it must be protected by a GFCI receptacle or circuit.
Installation Installation Instructions ! NOTE: Two people are required for installation. 1. Prepare a wall with a framed opening, following the dimensions shown in Figure 3. The fireplace can either be installed partially-recessed (2x4 frame) or flush-mounted (2x6 frame). CAUTION: Decorative finishing material (such as brick) should be limited to ½" (13 mm) overhang to ensure adequate flow of heated air out of the firebox area. CAUTION: This fireplace is NOT load-bearing.
Installation Figure 5 Main Control Board Flame Panel Mounting Holes 6. Drive four supplied mounting screws through the four mounting holes located on the inside surface of the fireplace chassis, into wall studs. (Figure 5) 7. Complete the wiring according to instructions in the Electrical Installation section (pages 12–13). 8. Complete the installation using the instructions in the following sections: Mirrored Glass Installation (page 15), Arranging Media (page 15), Front Glass Installation (page 16).
Installation Electrical Installation WARNING: The installation of the electric fireplace must comply with the applicable Local and/or National Electrical Codes and utility requirements. Use the appropriate wire to meet local and national electrical codes for rated power consumption. CAUTION: A dedicated, properly fused 15 Amp circuit is recommended, rated for the appropriate voltage (120 V, 240 V).
Installation 240 V Hardwire Installation Power Cord Installation FIREPLACE JUNCTION BOX FIREPLACE JUNCTION BOX You will need a 4-wire 240 V supply (L1, L2, Neutral, and Ground). 1. Connect the black L1 wire fromWhite the- Neutral unit to the L1 wire White - Neutral from the power supply with a wire connector. 120 V Black - L1 L 2. Connect the yellow L2 wire from Black the- unit to the L2 POWER SUPPLY wire from the power supply with a wire connector. Red - L2 (BREAKER 3.
Installation Heater Hardware Disconnect The fireplace heater can be permanently disabled by removing the electronic jumper on the main control board. ! NOTE: Heater hardware disconnect will permanently disable the heater and fan. Follow these instructions only when an installation without heat is required. Temporary disabling of the heater can be achieved through the hidden touch controls. See “Heat Disable” in Operation section (page 18) for instructions.
Installation Mirrored Glass Installation 1. Locate and remove the screws securing the mirrored glass bracket to the unit, along the top of the opening, and set bracket and screws aside. (Figure 11) 2. Remove the provided suction cup from the inside cavity of the unit (not found in XLF50 units). 3. Ensure that the back of the glass is clean and free from particles and fingerprints. 4. Secure the suction cup to the mirrored glass on the reflective side 5.
Installation Front Glass Installation 1. Ensure that the mirrored glass and the inside of the front glass is clean and free from particles and fingerprints. 2. Secure the suction cup (if provided) to the outside of the front glass. 3. Lift the front glass and carefully place the front glass into the lip located at the bottom of the opening of the firebox. 4. Tilt the glass into a vertical position. 5. Secure the front glass using the provided screws and hex key.
Operation General Operation WARNING: This electric firebox must be properly installed before it is used. This firebox operates with Comfort$averTM technology, which automatically adjusts the fan speed and heater wattage to safely and precisely match the requirements of the room based on the thermostat setting. The heater operates such that once the room reaches the set point, the fan and heater will continuously run at a low level, to maintain the desired room temperature.
Operation Standby Flame Effect Heat Heat Disable Press When the unit is turned back on, it will retain the previously used settings. Press to turn the flame effect on or off. Press to turn the heat on or off. The fireplace can be operated in heat only mode by turning off the flame and color effects. Press and hold and at the same time for 3 seconds to disable or enable the heat function. This action must be performed on the hidden touch controls. When the heat is disabled and either the display.
Operation Brightness Timer Press repeatedly to cycle through the brightness and flicker modes. Solid H - High Brightness Solid L - Low Brightness Cycle H - High Brightness with flickering media Cycle L - Low Brightness with flickering media Press repeatedly until the desired number of hours of the timer is displayed. When this function is active, the fireplace will turn off after a set amount of time. The timer can be set from 30 minutes to 8 hours in intervals of 30 minutes.
Maintenance Remote Control Battery Replacement To replace the battery: Slide battery cover open on the remote control. Correctly install one 3 Volt (CR2032 [longer life] or CR2025) battery in the battery holder with the + side facing up. Close the battery cover. The battery must be recycled or disposed of properly. Check with your Local Authority or Retailer for recycling advice in your area.
Troubleshooting For more troubleshooting, consult the XLF Service Manual which can be found at www.dimplex.
Wiring Diagrams XLF50 XLF50 CERAMIC ELEMENT MAIN CONTROL BOARD FAN THERMAL CUTOUTS FAN THERMISTOR M POWER ADAPTER FLICKER MOTOR FLAME LED ASSEMBLY MEDIA LED ASSEMBLY MEDIA LED ASSEMBLY XLF60 XLF60 CERAMIC ELEMENT MAIN CONTROL BOARD FAN THERMAL CUTOUTS FAN THERMISTOR POWER ADAPTER M FLICKER MOTOR FLAME LED ASSEMBLY MEDIA LED ASSEMBLY MEDIA LED ASSEMBLY XLF74 XLF74, XLF100 CERAMIC ELEMENT XLF100 MAIN CONTROL BOARD FAN THERMAL CUTOUTS FAN THERMISTOR M POWER ADAPTER FLICKER MOTOR RELA
Warranty IGNITEXL™ 5-YEAR LIMITED WARRANTY Section 1 Products to which this Limited Warranty Applies This Limited Warranty applies to your newly purchased Dimplex electric fireplace with model numbers XLF50, XLF60, XLF74, and XLF100. This Limited Warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA and the District of Columbia except for Hawaii and Alaska.
We value your feedback! Your input helps to create even better products and experiences. Share the warmth and leave a review. dimplex.com/sharethewarmth 1-888-346-7539 | www.dimplex.com In keeping with our policy of continuous product improvement, we reserve the right to make changes without notice.
