DWG Series GSM/CDMA VoIP Gateway User Manual (Version: 2.0) Dinstar Technologies Co., Ltd. Address: Floor 6, Guoxing Building, Changxing Road, Nanshan District, Shenzhen, China 518057 Telephone: +86 755 6130 2265 Fax: +86 755 2645 6659 Emails: sales@dinstar.com, support@dinstar.com Website: www.dinstar.
DWG Series GSM/CDMA VoIP Gateway User Manual Content Chapter 1 Equipment introduction ...................................................................................................2 1.1 Introduction........................................................................................................................2 1.2 Scenario of products...........................................................................................................2 1.3 Product appearance ..............................
DWG Series GSM/CDMA VoIP Gateway User Manual Chapter 1 Equipment introduction This chapter mainly introduces functions and structures of DWG (Dinstar wireless VoIP Gateway) series GSM/CDMA wireless VoIP gateways, which are named as DWG2001/DWG2004/DWG2008. 1.1 Introduction DWG2001/DWG2004/DWG2008 serial is full functions VoIP gateway based on IP and GSM/CDMA wireless network. DWG200X provides a flexible network configuration, powerful features, and good voice quality.
DWG Series GSM/CDMA VoIP Gateway User Manual DWG2004/DWG2008 can be implemented as VoIP call termination in VoIP operation, the solution shown as figure 1‐2 Figure 1‐2 1.3 Product appearance Figure 1‐3 Front view of DWG2004/DWG2008 Figure 1‐4 DWG2001 Notes: DWG2004 equips 4 antennas, DWG2008equips 8 antennas; both models have the same appearance.
DWG Series GSM/CDMA VoIP Gateway User Manual Model Network Type Interface DWG2001 GSM/CDMA 1WAN,1LAN ,1SIM channel DWG2004 GSM/CDMA 1WAN,3LAN, 4SIM channels DWG2008 GSM/CDMA 1WAN,3LAN, 8SIM channels Table 1‐1 DWG2001/DWG2004/DWG2008 interface description 1.4 Functions and features 1.4.
DWG Series GSM/CDMA VoIP Gateway User Manual z One number access z Open API for SMS, support USSD z Echo Cancellation (with ITU‐T G.168/165 standard) z Automatic negotiate network z Hotline 1.4.3 Industrial Standards supported: z Stationary use environment: EN 300 019: Class 3.1 z Storage environment: EN 300 019: Class 1.2 z Transportation environment: EN 300 019: Class 2.
DWG Series GSM/CDMA VoIP Gateway User Manual view). Figure 1‐5 Front view of DWG2004/DWG2008 Figure 1‐6 Front view of DWG2001 1.5.
DWG Series GSM/CDMA VoIP Gateway User Manual Figure 1‐7 Rear view of DWG2004/DWG2008 2) Description of interfaces on rear view of DWG2001 shows as below: Figure 1‐8 Rear view of DWG2001 1.6 Restore factory setting Push RST button for 6 seconds of DWG2001/DWG2004/DWG2008, the device will restore factory setting.
DWG Series GSM/CDMA VoIP Gateway User Manual Chapter 2 Equipment installation This chapter mainly introduces DWG2001/DWG2004/DWG2008 hardware installation and connection of equipment. 2.1 Installation notice DWG2004/DWG2008 used AC110~220V, 50/60Hz AC power supply, DWG2001 uses DC12V power. Power supply should ensure the reliability and stability; otherwise, it may damage the SIM card or device. In addition, make sure the power supply connects to ground bar well.
DWG Series GSM/CDMA VoIP Gateway User Manual 2.2 Installation procedure The outlook of DWG2001/DWG2004/DWG2008 looks like a 1U chassis; to install hardware the cable is needed. After unpacking the equipment, please do follow the procedure as following steps: 2.2.1 Install SIM card When installing SIM card, opening blank panel of SIM slot, procedure shows as below: 2.2.2 Antenna installation Figure 2‐5 shows as below a compelete installation: Figure 2‐5 Antenna installation 2.2.
DWG Series GSM/CDMA VoIP Gateway User Manual DWG2004/DWG2008 works in Bridge mode DWG2001 works in Route mode Figure 2‐7 DWG2001 connection 2.3 Establishing remote access Figure 2‐8 Remote login environments After installation of DWG2001 /DWG2008, creating a remote access for technical support.
DWG Series GSM/CDMA VoIP Gateway User Manual Chapter 3 Network configuration In this chapter we will introduce the initial configuration of DWG2001/DWG2004/DWG200 gateway. All of the network parameters of the gateway can be configured by IVR guidance. 3.
DWG Series GSM/CDMA VoIP Gateway User Manual 3.3 General feature codes for system setting Dial numbers Features *114# Play the phone NO. Check the TT number of gateway (using just when the *115# device interconnects with other series of DINSTAR products) Set IP address(static/DHCP), a can be digit 1 or 2,*150*1# is *150*a# static IP address mode, *150*2# is DHCP mode Configure IP address, a, b, c, d are the four fields of IP *152*a*b*c*d# address. Configure subnet mask.
DWG Series GSM/CDMA VoIP Gateway User Manual 172 * 16 * 0 * 100 #" hang up when hear “setting successful" message; 4) configure subnet mask: Dial the SIM card phone number, enter "*153*255*255*0*0#" hang up when hear “setting successful" message; 5) Configure gateway: Dial the SIM card phone number, enter "*156*172*16*0*1#" hang up when hear “setting successful" message; 6) Please wait about ten seconds when finishing the operations, restart device.
DWG Series GSM/CDMA VoIP Gateway User Manual Chapter 4 WEB configuration This charpter describes web configuration of DWG2001/DWG2004/DWG2008. 4.1 Preparing WEB configuration includes the following components: network configuration, system information, mobile configuration and system configuration. Dial “* 158 #” to get the IP address of the gateway, log on the web interface by a browser. 4.
DWG Series GSM/CDMA VoIP Gateway User Manual 4.3 WEB configuration 4.3.1 WEB Operation Guide DWG2001/DWG2004/DWG2008 WEB configuration interface consists of the navigation tree and the detail configuration interfaces. Figure 4‐3‐1 WEB introduce Go through navigation tree, user can check, view modify, and set the device configuration on the right of configuration interface.
DWG Series GSM/CDMA VoIP Gateway User Manual 4.4 System Information Figure 4‐3‐2 system information System information interface shows the basic information of status information, Mobile information and SIP information. 4.4.
DWG Series GSM/CDMA VoIP Gateway User Manual 【Network Traffic Statistics】Calculates the netflow, including the total bytes of message received and sent. 【Version information】shows the current firmware version, for example EIA AOS 9.50.16 PCB 29.1 LOGIC 0 BIOS 1, Built on Sep 21 2010, 17:32:25; 4.4.2 Mobile information Figure 4‐3‐4 mobile information Display GSM / CDMA channel and network status information, detailed shown as below: 【Port】Numbers of ports of GSM/CDMA.
DWG Series GSM/CDMA VoIP Gateway User Manual 4.5 Network Configuration The navigation tree of the route mode and bridge mode as below: Figure 4‐3‐6 bridge mode Figure 4‐3‐7 route mode In the navigation tree of route mode, will have extra items of “MAC Clone”,”DHCP Server” ,”DMZ Host” ,”forward Rule”,”Static Route” . 4.5.1 Local network Under the route mode, WAN port connects with ADSL modem, and LAN port connects with local network. It will be used as a small switch when working in brigde mode.
DWG Series GSM/CDMA VoIP Gateway User Manual Figure 4‐3‐9 WEB interface of Route mode Detailed parameters describled as below: 【Work mode】two options of route mode and bridge mode, default is bridge mode. z Network Configuration 【Link Speed & Duplex】the 5 options are “Auto Detect”,” 10Mbps/Half Duplex”,”10Mbps/Full Duplex”, “100Mbps/Half Duplex” and “100Mbps/Full Duplex”. Default is “Auto Detect” 【Obtain IP Address Automatically】enable the device obtain IP Address automatically or not.
DWG Series GSM/CDMA VoIP Gateway User Manual 【IP Address】set IP address by manual configuring. Default is 192.168.1.1 【Subnet Mask】set the lan port Subnet Mask by manual configuring, Default is 255.255.255.0 z DNS Server 【Obtain DNS Server Address Automatically】When enable the WAN port option of “Obtain DNS Server Address Automatically” , which will be enabled subsequently.
DWG Series GSM/CDMA VoIP Gateway User Manual The subnet mask, gateway, DNS info will also be allocated to network devices automatically by DHCP protocol. Generally, there is no need to configure those items. NOTE: Please configure the start and end IP addressed in IP address pool, subnet mask and gateway in the same network segment. Other devices in this network may not work when obtaining the IP address. 4.5.
DWG Series GSM/CDMA VoIP Gateway User Manual channels communication based on certain protocol(TCP or UDP). If DMZ host and forwarding rules have conflicts, will be determined by forwarding rules configurations. 4.5.6 Static route(Option under “route mode”) Static route is the route rules in IP communication. Generally speaking, no need to config static route.
DWG Series GSM/CDMA VoIP Gateway User Manual 【Dial Tone Gain（Mobile Side）】it is the dial tone volume of call waiting, dial tone of mobile module when call out. Usually adopt the default configuration. 【Select Band】according to carrier’s band standards. Standards are as belows: GSM：850/900/1800/1900 MHz ; CDMA：800 MHz; 【Forward enable】enable the function of trunk call in for mobile phone user ID, that is, choosing one user ID of the SIM channels as the access No of DWG device.
DWG Series GSM/CDMA VoIP Gateway User Manual Figure 4‐3‐16 Mobile Configuration Configuration details are as below： 【Mobile Number】SIM card user ID of the channel. That must be configured when “one access No.” funciton enable. 【Enable Call Duration Limitation】this function is to limit the max call duration of channel. The max call duration is between 1 to 65535 minutes. 【Maximum Call Duration】defines a value by users. That will limit the SIM/UIM card’s total call duration.
DWG Series GSM/CDMA VoIP Gateway User Manual Figure 4‐3‐17 Configuration of SIM/UIM Card Lock Configurations are as below: 【Select Port】select the Channel No. which need to be locked. 【SIM Card Lock】SIM card lock or unlock. Default is “No”. 【PIN Code】correct PIN code is needed to lock or unlock the SIM card. 4.6.4 PIN Management Figure 4‐3‐18 PIN Management Detailed description as below: 【PIN management】PIN is the password of SIM card personal identification.
DWG Series GSM/CDMA VoIP Gateway User Manual 4.6.6 SMS Figure 4‐3‐19 SMS sending Configurations are as below: 【Select Port】users can select a defined channel or random channel to send SMS. Input the recevier’s mobile phone No to send SMS. 【Addressee】mobile phone No. of the receiver 【Message】content of the SMS. The length is limited to 300 characters. 4.6.
DWG Series GSM/CDMA VoIP Gateway User Manual Notes:please check with local service provider before using this service. 4.7 Routing configuration 4.7.1 Routing parameter Globle parameters, it will take effect while number manipulation configured Route calls after manipulation: the parameters indicate that the gateway will select IP‐>Tel or Tel‐>IP routes after number manipulation completed.
DWG Series GSM/CDMA VoIP Gateway User Manual Function: When the softswitch/ sip server send the call traffic to gateway directly, must be added IP‐>Tel routing. Parameter Description Parameter Parameter Description Index It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. Description It describes the route for the ease of identification.
DWG Series GSM/CDMA VoIP Gateway User Manual The caller party coming from IP Group 18 will match source prefix ”any”, ”any” is a wildcard string include anonymous calls. At same time, destination prefix must match with ” 13[4‐9]xxxxxxxx|6xxx|10086”.
DWG Series GSM/CDMA VoIP Gateway User Manual Prefix ”any” is a wildcard string which will match anonymous calls as well. 4.7.3 Tel‐>IP Routing Function: This item uses to configure incoming call routes which can be used for recieve the calls from the GSM. Parameter Description Parameter Parameter Description Index It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. Description It describes the route for the ease of identification.
DWG Series GSM/CDMA VoIP Gateway User Manual the connected number y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc. y 0xxxx: consist of some digits such as 015,08,09 1[3‐8]6:consist of some prefix, include 136,146,156,166,176, 186 Destination Its specifies destination Port or Port Group Example: Index 0: its a default route configured in gateway It allows any number from source port 0 send call to SIP server with any prefix.
DWG Series GSM/CDMA VoIP Gateway User Manual Index 31: add GSM to GSM route,its mainly used for saving the cost between two carriers It indecates that calls coming from Port 0 will match the prefix 13[58], ”13[58]” include prefix 135 and 138, caller number can’t match prefix 135 and 138 will reject by gateway. Meanwhile sending the calls to Port Group 31 if called number match with prefix 133. 4.
DWG Series GSM/CDMA VoIP Gateway User Manual Description It describes the route for the ease of identification. Its value is character string Source IP It specifies the source IP which will send the calls to gateway y Any: any IP address y IP: specific an IP address y IP Group: specific an IP group Source Prefix All the caller number must match the source prefix. It specifies the source prefix allow to send call out y Any: include anonymous, 0xxxx, 1[2‐9]xxxx etc.
DWG Series GSM/CDMA VoIP Gateway User Manual whom match with the prefix ”2547” will delete 3 digits in front of it and replace it by digit ”0”. 4.9 Operation Function It is an optional configuration item. Operation configuration essentially involves allow, barring some IP and IP Group send calls to certain numbers. It includes: forbid call, call allowance, auto call, and password authentication. Parameter Description Parameter Parameter Description Index It uniquely identifies a route.
DWG Series GSM/CDMA VoIP Gateway User Manual Example Index 31: barring the certain calling number from IP 14 It indicates that calling party from IP 14 matched prefix 2877, and also called party matched prefix 07 are not allowed call out. The calls match this rule will be rejected by gateway. Index 29: definite a rule for IP 17 that all the calls must go with valid password authentication. 4.3.
DWG Series GSM/CDMA VoIP Gateway User Manual Function This configuration step is necessary, and is used to add port group in gateway. The port group will referenced by IP‐>Tel routing and number manipulation. Parameter Description Parameter Parameter Description Index It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. Description It describes the route for the ease of identification.
DWG Series GSM/CDMA VoIP Gateway User Manual 4.3.9 IP Group Configuration 1) IP configuration Function Add remote IP of Softswitch, SIP server which will send call traffics to gateway. Parameter Description Parameter Parameter Description Index It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. Description It describes the route for the ease of identification.
DWG Series GSM/CDMA VoIP Gateway User Manual Function This configuration is optional, and is used to add the IP that have the same attributes to an IP group. The IP group will referenced by IP‐>Tel routing and number manipulation. Parameter description Parameter Parameter Description Index It uniquely identifies a route. Its value is assigned globally, ranging from 0 to 31. Description It describes the route for the ease of identification.
DWG Series GSM/CDMA VoIP Gateway User Manual 1) System configuration Figure 4‐3‐20 System Configuration Configuration details as below: 【Voice Prompt Language】configure the voice prompt of DWG., e.g. configure voice prompt of IP address success or failure. DWG supports English and Chinese. Users can customize other languages. The default setting is in Chinese. z Provision configuration Provision is used to maintain the devices. E.g. Provision can config, update and remote manage the devices in bulk.
DWG Series GSM/CDMA VoIP Gateway User Manual 2) Service configuration (for SIP only) Service Configuration is used for configuring voice calls and some small businesses, such as Call Progress Tone, codec, silence suppression, * service, the second dial and so on Figure 4‐3‐21 Service Configuration Detailed description as follow: 【LOCAL RTP PORT Channel】means the initial allocation of Channel when RTP voice stream transmit in the IP network , in general, using the factory default values.
DWG Series GSM/CDMA VoIP Gateway User Manual 【Call Progress Tone】each country has its different call progress tone required standards, such as busy tone, ring back tones and ring tone standards, users can select the area standard from here . 【Preferred Coders】means the code format when Voice transfer on IP network, support PCMA, PCMU, G.723.1 andG.729AB. Note: when the preferred codec switch between G.723.1 and G.
DWG Series GSM/CDMA VoIP Gateway User Manual 【CLID Mode】Select the name under the special needs , the most common way is use the default User ID 【Other Configuration】： Enable”*“at the beginning private internal service: the default is enable, that the private internal network‐related service refer to Configuration query, recording, adjust the volume, restore the factory default values, etc.
DWG Series GSM/CDMA VoIP Gateway User Manual 3) SIP Configuration (for SIP only) Figure 4‐3‐22 SIP Configuration SIP Configuration: used for Configuring VoIP channel, add SIP Registry Platform and local SIP Channel, and configure SIP protocol and other related information Detailed description as follow: z SIP PROXY 【SIP Server Address】use for configure SIP server address and Channel, the address can be IP Address, also can be a domain name (DNS should to be able to resolution), the details please advis
DWG Series GSM/CDMA VoIP Gateway User Manual 【Register Interval】means how often the equipment will register once to the SIP server/proxy 【T1】 used to define the SIP protocol T1 timer value, default is 500ms; 【T2】 used to defines the SIP protocol timer values, default value is 4000ms; 【T3】used to define the T2 timer value in SIP protocol, the default is 5000ms; 【Keep alive Interval】used for keep communicate between equipment and the SIP server that make the device is in the best available Registered.
DWG Series GSM/CDMA VoIP Gateway User Manual the hotline User ID. If no need this feature, just left it blank 【Auto‐Dial Delay Time】Offhook Auto‐Dial delay time, the range is 0‐10 seconds 5) Fax Configuration Figure 4‐3‐23 Fax Configuration Fax Configuration use for configure fax, and support pass‐Through and T.38 fax mode, the maximum baud rate supported 14400bps Interface describe as following: 【Fax way】support T.
DWG Series GSM/CDMA VoIP Gateway User Manual Figure 4‐3‐24 firmware upload Select the upgrade program under correct directory services, and then click upload will complete upgrade the firmware. NOTE: during the upgrade process, please do not swtich off the power supply, equipment may paralyze. 2) IVR Voice Prompt Upload By default, when PSTN call incoming, the system will play the default IVR, and also the user can load custom IVR.
DWG Series GSM/CDMA VoIP Gateway User Manual 3) Login password Figure 4‐3‐25 IVR Voice Prompt Upload When using web or telnet Configuration, please enter default user name and password. User can modify the login name and password. 4) Factory Reset Figure 4‐3‐26 Factory Reset Be careful do this operation, after restore factory setting, all the parameters will be changed to the factory default. 6) Restart Figure 4‐3‐27 Restart When system restarts, user click RESET button on the web.
DWG Series GSM/CDMA VoIP Gateway User Manual Chapter 5 FAQ z Device have been connected to network physically, but the network cannot be connected or network communication is not normal 1) Make sure the network cable is ok or not , can through view the device WAN port or LAN port indicator light to determine the physical connection is working or not; 2) Make sure the connected network devices (router, switch or hub) support 10M/100M adaptive, if not, connect the Equipment directly to PC, landing WEB and i
DWG Series GSM/CDMA VoIP Gateway User Manual z When calling out, the callee’s phone shows wrong caller ID: 1) Ask the callee checks whether the device is failure or device battery power is low 2) Make sure the callee has been subscribed called User ID display service 3) If only part of the caller User ID with this problem, please contact the Telecom Carrier to identify the problem.
DWG Series GSM/CDMA VoIP Gateway User Manual Configuration interface section) 6) Check the equipment network environment for the softswitch platform, monitor the network condiation, make sure the network is solid Glossary GSM: Global System for Mobile Communications CDMA: Code Division Multiple Access FMC: Fixed Mobile Convergence SIP: Session Initiation Protocol MGCP: Media Gateway Control Protocol DTMF: Dual Tone Multi Frequency USSD: Unstructured Supplementary Service Data PSTN：Public Switched Telephon
