www.getdio.
www.getdio.com Important safety warning Thank you for purchasing a DiO product. Before installing this product, please read these instructions for use carefully and ensure that you follow the instructions to ensure the safety of persons. In the event of non-compliance with these instructions, liability and the warranty of the motor will no longer be valid. Please contact a professional if in doubt.
www.getdio.com • Do not disassemble the product. Do not insert sharp objects into the motor. • Fit the power cable inside waterproof protective tubing if it is to be installed externally in order to avoid any possible ingress of water into the motor. • Do not use the motor if the power cable is damaged, and contact customer service or the dealer immediately. • Do not make holes in the motor and pay particular attention to the length of the retaining screws of the roller of the shutter or blind.
www.getdio.com Installation I. Installing the motor Please follow the instructions for your shutter or blind to remove it and gain access to the roller. Warning, before installing the motorised unit, make sure you block off the existing wired switch if you had an electrical installation or remove any equipment which is not needed for a motorised operation such as the strap or the hand crank. Warning, before installing, check that the motor is suitable for the shutter to be automated (see product box).
www.getdio.com 3 Make a mark on the roller depending on the distance measured in point 1 and using the screw provided, screw the roller to the tubular motor. Make sure that the screw is screwed onto the plastic drive wheel and not onto the metal tube. + 4 Attach the retaining bracket on the appropriate side of the housing. 5 Attach the roller with the motor installed in the housing, slotting the bracket into the retaining head (see diagram).
www.getdio.com 6 Finish by securing the motor head using the pin supplied. 7 Refit the shutter onto the roller in accordance with the instructions for your shutter or blind, taking care that the power cable or antenna does not impede it from rolling up. Warning, if the shutter is attached with screws, ensure that the screws are not long enough to touch the motor inside the roller. II. Connecting to the power supply Connection to the power supply must be undertaken by a qualified electrician.
www.getdio.com III. Installing the remote control unit Important: If you install several roller shutter motors, please install each motor separately with its remote control unit. The motor is connected (paired) with its remote control unit the first time the shutter motor is switched on. Please do not connect all your shutter motors at the same time or they will all be linked to the same control unit. The motor will retain the first remote control unit in memory in the event of a power failure.
www.getdio.com Note: You can install up to 12 DiO 1.0 wireless control units per shutter motor. The DiO 1.0 wireless roller shutter motor is not compatible with the switch micro-module (Ref 54700). Warning: Do not use more than one control unit at the same time. Do not forget to remove or block off the wired switch to prevent damaging the new shutter motor. Deleting a control unit 5 In certain cases, it may be useful to delete one or more control units to free up memory (maximum 12 control units).
www.getdio.com - If the shutter stops before the required up position, increase the end stop by gradually turning the bottom screw anti-clockwise (towards '+') with the adjustment tool provided. The shutter will gradually go up as you turn the screw. If the adjustment lasts more than two minutes, press the ON ('I') button to start raising the shutter again.
www.getdio.com Partial opening of the shutter Press the ON ('I') button on the remote control to start opening the shutter. Press the same button again to stop the shutter at the required position. Add control points You can add DiO 1.0 accessories to control your shutter with other control units (switch, remote control, smartphone, etc.; maximum 12 control units) - see III.4. Installing the remote control unit.
www.getdio.com 4) Check the condition of the remote control battery. 5) Check that there is distance of one metre between each radio antenna to avoid any interference. I cannot link my wireless motor with a control unit (remote control unit, switch, …) 1) Check the condition of the remote control battery. 2) Make sure that your motor is not already connected to 12 control units. If it is, partially empty the memory of the motor concerned and reconnect it to the new control unit (See III.4.
www.getdio.com Specifications Roller Shutter Motor Frequency: 433.92MHz Radio protocol: DiO 1.0 (433MHz by DiO) Transmission range: 50m (free field) Power supply: 230V - 50Hz Operating temperature: -10 to 40° C Internal use: IP44 Product Torque 10 Nm MVR-40-10RF X MVR-60-10RF X MVR-60-20RF 20 Nm Tubing axis Max power Rotation speed 40 mm 150W / 0.65 A 16 rpm 60 mm 115W / 0.55 A 16 rpm 60 mm 165W / 0.75 A 16 rpm 60 mm 260 W / 1.
