Page 1 of 51 Safety Test Report Report No.: AGC04298180501ES01 PRODUCT DESIGNATION : 4G Wireless Router BRAND NAME : Tuoshi MODEL NAME : LT15, LT210 CLIENT : DATE OF ISSUE : Jun. 06, 2018 STANDARD(S) : EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 REPORT VERSION : V1.0 SHENZHEN TUOSHI NETWORK COMMUNICATIONS CO., LIMITED Attestation of Global Compliance (Shenzhen) Co., Ltd.
Report No.: AGC04298180501ES01 Page 2 of 51 TEST REPORT EN 60950-1 Information technology equipment-SafetyPart 1: General requirements Report Reference No. ...................... : AGC04298180501ES01 Tested by (+ signature) ......................: Johnson Ye Reviewed by (+ signature) ................: Jenny Li Matte He Approved by (+signature) ..................: (Authorized Officer) Date of issue .......................................: Jun. 06, 2018 Contents ...........................................
Report No.: AGC04298180501ES01 Page 3 of 51 Test item Product designation ...........................: 4G Wireless Router Brand name ........................................: Tuoshi Test model ..........................................: LT15 Series model .......................................: LT210(All models are identical except for model name and color) Rating(s)..............................................: 12V , 1A Particulars Equipment mobility .....................................................
Report No.: AGC04298180501ES01 Page 4 of 51 Attachment Attachment A................................................................. : Photos of product General remarks This report shall not be reproduced except in full without the written approval of the testing laboratory. The test results presented in this report relate only to the item tested. “(See remark #)” refers to a remark appended to the report. “(See appended table)” refers to a table appended to the report.
Report No.: AGC04298180501ES01 Page 5 of 51 Copy of marking plates The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks. Remark: 1) The CE marking and WEEE symbol (if any) should be at least 5mm and 7mm respectively in height. 2) The markings and instructions are the minimum requirements required by safety standard.
Report No.: AGC04298180501ES01 Page 6 of 51 EN 60950-1 Clause Requirement – Test Result – Remark 1 GENERAL P 1.5 Components P 1.5.1 General P Verdict Comply with IEC 60950 or relevant component standard Components which were found to affect safety aspects comply with the requirements of this standard or with the safety aspects of the relevant IEC/EN component standards. (see appended table 1.5.1) P 1.5.
Report No.: AGC04298180501ES01 Page 7 of 51 EN 60950-1 Clause Requirement – Test Result – Remark 1.6.2 Input current (See appended table 1.6.2) 1.6.3 Voltage limit of hand-held equipment 1.6.4 Neutral conductor 1.7 Marking and instructions 1.7.1 Power rating Verdict P N Class Ⅲ equipment, no neutral conductor. N P See below P Rated voltage(s) or voltage range(s) (V) ............. : 12V -- Symbol for nature of supply, for d.c. only .............
Report No.: AGC04298180501ES01 Page 8 of 51 EN 60950-1 Clause Requirement – Test 1.7.7.3 Terminals for d.c. mains supply conductors N 1.7.8 Controls and indicators P 1.7.8.1 Identification, location and marking ..................... : It is obviously unnecessary. N 1.7.8.2 Colours ............................................................... : The colours used for LED are indicating function. No safety consideration. P 1.7.8.3 Symbols according to IEC 60417 .........................
Report No.: AGC04298180501ES01 Page 9 of 51 EN 60950-1 Clause Requirement – Test Result – Remark 2.1.1.8 Energy hazards – d.c. mains supply Not directly connect to mains supply Verdict N a)Capacitor connected to the d.c. mains supply .. : N b)Internal battery connected to the d.c. mains supply ................................................................... : N 2.1.1.9 Audio amplifiers .................................................... : No any amplifiers N 2.1.
Report No.: AGC04298180501ES01 Page 10 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict Measured current (mA)......................................... : N Measured voltage (V) ........................................... : N Measured capacitance (nF or F) ........................ : N 2.4.3 Connection of limited current circuits to other circuits N 2.
Report No.: AGC04298180501ES01 Page 11 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict N Rated current (A), type and nominal thread diameter (mm) ...................................................... : 2.6.4.3 Separation of the protective earthing conductor from protective bonding conductors N 2.6.5 Integrity of protective earthing N 2.6.5.1 Interconnection of equipment N 2.6.5.2 Components in protective earthing conductors and protective bonding conductors N 2.6.5.
Report No.: AGC04298180501ES01 Page 12 of 51 EN 60950-1 Clause Requirement – Test Result – Remark 2.8.7.3 Endurance test N 2.8.7.4 Electric strength test N 2.8.8 Mechanical actuators N 2.9 Electrical insulation N 2.9.1 Properties of insulating materials 2.9.2 Humidity conditioning N Humidity (%),temperature (°C) ........................... : N 2.9.3 Grade of insulation N 2.9.4 Separation from hazardous voltages N Method(s) used ...................................................
Report No.: AGC04298180501ES01 Page 13 of 51 EN 60950-1 Clause Requirement – Test 2.10.3.8 Transients from telecommunication networks and cable distribution systems .................................. : N 2.10.3.9 Measurement of transient voltage levels N a)Transients from a mains supply N For a.c. mains supply ......................................... : N For d.c. mains supply ......................................... : N b)Transients from N 2.10.4 Creepage distances N 2.10.4.
Report No.: AGC04298180501ES01 Page 14 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict Electric strength test N Rountine test N Additional insulation in wound components N Working voltage .................................................... : N -basic insulation not under stress ......................... : N -Supplementary, reinforced insulation .................. : N 2.10.6 Construction of printed boards N 2.10.6.1 Uncoated printed boards N 2.10.6.
Report No.: AGC04298180501ES01 Page 15 of 51 EN 60950-1 Clause Requirement – Test Result – Remark The insulation of the individual conductors is suitable for the application and the working voltage. 3.1.4 Insulation of conductors 3.1.5 Beads and ceramic insulators N 3.1.6 Screws for electrical contact pressure N 3.1.7 Insulating materials in electrical connections N 3.1.8 Self-tapping and spaced thread screws N 3.1.
Report No.: AGC04298180501ES01 Page 16 of 51 EN 60950-1 Clause Requirement – Test 3.3.1 Wiring terminals N 3.3.2 Connection of non-detachable power supply cords N 3.3.3 Screw terminals N 3.3.4 Conductor sizes to be connected N Rated current (A), cord/cable type, cross-sectional area (mm2) ............................................................ : -- Wiring terminal sizes N Rated current (A), type and nominal thread diameter (mm) .....................................................
Report No.: AGC04298180501ES01 Page 17 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict Test: force (N) ....................................................... : N 4.2 Mechanical strength P 4.2.1 General See below P Rack-mounted equipment. N 4.2.2 Steady force test, 10 N N 4.2.3 Steady force test, 30 N N 4.2.4 Steady force test, 250 N 4.2.5 Impact test 250N applied to outer enclosure. No energy or other hazards. No hazards P P Fall test P Swing test P 4.2.
Report No.: AGC04298180501ES01 Page 18 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict -Excessive discharging rate for any battery N Oil and grease No Oil and grease. Equipment in intended use not Dust, powders, liquids and gases considered to be exposed to these. Containers for liquids or gases No containers for liquids or gases Flammable liquids ................................................. : The equipment does not contain flammable liquid. Quantity of liquid (l) ............
Report No.: AGC04298180501ES01 Page 19 of 51 EN 60950-1 Clause Requirement – Test Considered to cause injury. 4.4.5.2 Result – Remark c) ............ : Verdict N Protection for users N Use of symbol or warning ..................................... : N Protection for service persons N Use of symbol or warning ..................................... : N 4.5 Thermal requirements P 4.5.1 General P 4.5.2 Temperature tests 4.4.5.3 (see appended table 4.5) Normal load condition per Annex L ...
Report No.: AGC04298180501ES01 Page 20 of 51 EN 60950-1 Clause Requirement – Test Result – Remark N Method 2, application of all of simulated fault condition tests 4.7.2 Conditions for a fire enclosure 4.7.2.1 Parts requiring a fire enclosure Verdict See appended table 1.5.1 P N Supplied by approved AC adaptor complied with LPS 4.7.2.2 Parts not requiring a fire enclosure 4.7.3 Materials P 4.7.3.1 General P 4.7.3.2 Materials for fire enclosures 4.7.3.
Report No.: AGC04298180501ES01 Page 21 of 51 EN 60950-1 Clause Requirement – Test 5.1.8 Touch currents to and from telecommunication networks and cable distribution systems and from telecommunication networks 5.1.8.1 Result – Remark Verdict N Limitation of the touch current to a telecommunication network and a cable distribution system N Test voltage (V) ................................................... : N Measured touch current (mA) .............................. : N Max.
Report No.: AGC04298180501ES01 Page 22 of 51 EN 60950-1 Clause Requirement – Test Result – Remark 6.1.1 Protection from hazardous voltages N 6.1.2 Separation of the telecommunication network from earth N 6.1.2.1 Requirements N Test voltage (V) ................................................... : -- Current in the test circuit (mA) ............................ : -- 6.1.2.2 Exclusions............................................................. : N 6.
Report No.: AGC04298180501ES01 Page 23 of 51 EN 60950-1 Clause Requirement – Test A ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE N A.1 Flammability test for fire enclosures of movable equipment having a total mass exceeding 18 kg, and of stationary equipment (see 4.7.3.2) N A.1.1 Samples ................................................................ : -- Wall thickness (mm) ............................................. : -- A.1.2 Conditioning of samples; temperature (°C) ..........
Report No.: AGC04298180501ES01 Page 24 of 51 EN 60950-1 Clause Requirement – Test A.3.2 Test procedure N A.3.3 Compliance criterion N B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and 5.3.2) N B.1 General requirements N Position ................................................................ : -- Manufacturer ....................................................... : -- Type ..................................................................... : -- Rated values ..........
Report No.: AGC04298180501ES01 Page 25 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict Method of protection ............................................. : -- C.1 Overload test N C.2 Insulation N Protection from displacement of windings ............ : N D ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS (see 5.1.4) N D.1 Measuring instrument N D.2 Alternative measuring instrument N E ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.
Report No.: AGC04298180501ES01 Page 26 of 51 EN 60950-1 Clause Requirement – Test Result – Remark G.6 Determination of minimum clearances ................. : N H ANNEX H, IONIZING RADIATION (see 4.3.13) N J ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6) N Metal used ........................................................... : -- K ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.7) N K.1 Making and breaking capacity N K.2 Thermostat reliability; operating voltage (V) .........
Report No.: AGC04298180501ES01 Page 27 of 51 EN 60950-1 Clause Requirement – Test Result – Remark M.3.2 Tripping device and monitoring voltage................ : N M.3.2.1 Conditions for use of a tripping device or a monitoring voltage N M.3.2.2 Tripping device N M.3.2.3 Monitoring voltage (V) .......................................... : N N ANNEX N, IMPULSE TEST GENERATORS (see 2.10.3.4, 6.2.2.1, 7.3.2 and clause G.5) N N.1 ITU-T impulse test generators N N.
Report No.: AGC04298180501ES01 Page 28 of 51 EN 60950-1 Clause Requirement – Test Result – Remark V ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1) N V.1 Introduction N V.2 TN power distribution systems N W ANNEX W, SUMMATION OF TOUCH CURRENTS N W.1 Touch current from electronic circuits N W.1.2 Earthed circuits N W.2 Interconnection of several equipments N W.2.1 Isolation N W.2.2 Common return, isolated from earth N W.2.
Report No.: AGC04298180501ES01 Page 29 of 51 EN 60950-1 Clause Requirement – Test CC.5 Compliance ........................................................... : N DD ANNEX DD, requirements for the mounting means of rack-mounted equipment N DD.1 General N DD.2 Mechanical strength test, variable N .................... : N DD.3 Mechanical strength test, 250N, including end stops ..................................................................... : N DD.4 Compliance ..........................
Report No.
Report No.: AGC04298180501ES01 Page 31 of 51 EN 60950-1 Clause 1.3.Z1 Requirement – Test Result – Remark Add the following subclause: 1.3.Z1 Exposure to excessive sound pressure The apparatus shall be so designed and constructed as to present no danger when used for its intended purpose, either in normal operating conditions or under fault conditions, particularly providing protection against exposure to excessive sound pressures from headphones or earphones.
Report No.: AGC04298180501ES01 Page 32 of 51 EN 60950-1 Clause Requirement – Test NOTE 1 Examples are hand-held or body-worn portable CD players, MP3 audio players, mobile phones with MP3 type features, PDA’s or similar equipment. Result – Remark Verdict N A personal music player and earphones or headphones intended to be used with personal music players shall comply with the requirements of this sub-clause. The requirements in this sub-clause are valid for music or video mode only.
Report No.
Report No.: AGC04298180501ES01 Page 34 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Zx.3 Warning The warning shall be placed on the equipment, or on the packaging, or in the instruction manual and shall consist of the following: - the symbol of Figure 1 with a minimum height of 5 mm; and - the following wording, or similar: Verdict N “To prevent possible hearing damage, do not listen at high volume levels for long periods.
Report No.: AGC04298180501ES01 Page 35 of 51 EN 60950-1 Clause Requirement – Test Zx.4.
Report No.: AGC04298180501ES01 Page 36 of 51 EN 60950-1 Clause 3.2.5.1 3.2.5.1 (A2:2013) 3.3.4 4.3.13.6 (A1:2010) Annex H Requirement – Test Result – Remark Verdict Replace “60245 IEC 53” by “H05 RR-F”; “60227 IEC 52” by “H03 VV-F or H03 VVH2-F”; “60227 IEC 53” by “H05 VV-F or H05 VVH2-F2”.
Report No.: AGC04298180501ES01 Page 37 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) 1.2.4.1 In Denmark, certain types of Class I appliances (see 3.2.1.1) may be provided with a plug not establishing earthing conditions when inserted into Danish socket-outlets. N 1.2.13.14 In Norway and Sweden, for requirements see 1.7.2.1 and 7.3 of this annex. N 1.5.7.
Report No.: AGC04298180501ES01 Page 38 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) “Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing – and to a cable distribution system using coaxial cable, may in some circumstances create a fire hazard.
Report No.: AGC04298180501ES01 Page 39 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) 1.7.5 (A2:2013) In Denmark, socket-outlets for providing power to other equipment shall be in accordance with the DS 60884-2D1:2011.
Report No.: AGC04298180501ES01 Page 40 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) 3.2.1.1 3.2.1.1 3.2.1.1 3.2.1.1 3.2.4 3.2.5.1 In Denmark, supply cords of single-phase equipment having a rated current not exceeding13 A shall be provided with a plug according to the Heavy Current Regulations, Section 107-2D1.
Report No.: AGC04298180501ES01 Page 41 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) 3.3.4 4.3.6 4.3.6 5.1.7.1 In the United Kingdom, the range of conductor sizes of flexible cords to be accepted by terminals for equipment with a RATED CURRENT of over 10 A up to and including 13 A is: • 1,25 mm2 to 1,5 mm2 nominal cross-sectional area.
Report No.: AGC04298180501ES01 Page 42 of 51 EN 60950-1 Clause Requirement – Test Result – Remark Verdict ZB ANNEX (normative) SPECIAL NATIONAL CONDITIONS (EN) 6.1.2.2 7.2 7.3 7.3 - passes the tests and inspection criteria of 2.10.11 with an electric strength test of 1,5 kV multiplied by 1,6 (the electric strength test of 2.10.10 shall be performed using 1,5 kV), and - is subject to ROUTINE TESTING for electric strength during manufacturing, using a test voltage of 1,5 kV.
Report No.: AGC04298180501ES01 Page 43 of 51 1.5.1 TABLE: list of critical components Object/part no. Manufacturer/ trademark P Type/model Mark(s) of conformity EN 60950TUVRheinla 1:2006+A11: nd 2009+A1:20 Report No.: 10+A12:201 50080331 1+A2:2013 001 UL UL94, UL796 ZPMV2 UL746 , UL E207780 UL94 Technical data Standard Input: 100-240V~ 50/60Hz, 0.6A Max.; output: 12V , 1A; Class II, LPS, 40°C AC Adapter SHENZHEN RUIDE ELECTRONICS INDUSTRY CO.
Report No.: AGC04298180501ES01 Page 44 of 51 2.5 TABLE: limited power source measurement N Isc (A) Measured Uoc (V) with all load circuits disconnected: VA Meas. Limit Meas. Limit -- -- -- -- -Note(s): -- 2.10.2 TABLE: Working voltage measurement Location N RMS voltage (V) Peak voltage (V) Comments -- -- -- -Note(s): -- 2.10.3 and 2.10.4 TABLE: clearance and creepage distance measurements Clearance cl and creepage distance dcr at/of: -- N Up (V) U r.m.s.
Report No.: AGC04298180501ES01 Page 45 of 51 Test results: Verdict - Chemical leaks -- N - Explosion of the battery -- N - Emission of flame or expulsion of molten metal -- N - Electric strength tests of equipment after completion of tests -- N Note(s):-4.3.8 TABLE: Batteries N Battery category ........................................................... : -Manufacturer ................................................................ : -Type/model ............................................
Report No.: AGC04298180501ES01 Page 46 of 51 4.5.5 TABLE: ball pressure test of thermoplastic parts N allowed impression diameter (mm) ........................ : Part -- -- Test temperature(°C) Impression diameter (mm) -- -- -Note(s): -4.7 TABLE: Resistance to fire P Part Manufacturer of material Type of material Thickness (mm) Flammability class Evidence -- -- -- -- -- -- Note(s): refer to table 1.5.1 TABLE: touch current measurement 5.
Report No.: AGC04298180501ES01 Page 47 of 51 U5, Pin 1-5 S-C 12 10min -- No damage and hazards. antenna S-C 12 10min -- No damage and hazards.
Report No.: AGC04298180501ES01 Page 48 of 51 Attachment A Photos of product Fig.1 – overview Fig.
Report No.: AGC04298180501ES01 Page 49 of 51 Fig.3 –overview Fig.
Report No.: AGC04298180501ES01 Page 50 of 51 Fig.5 –partview Fig.
Report No.: AGC04298180501ES01 Page 51 of 51 Fig.