F 275 325 225 180 Smoke Shut Down 375 High Cycle OFF Power ON www.zgrills.com WOOD PELLET GRILLS ZPG - 700D OWNER’S MANUAL 1-833-947-4557 EMAIL:support@zgrills.com WEBSITE:www.zgrills.
CONTENTS WARNINGS 3 COMPOENT LIST 4 ASSEMBLY INSTRUCTIONS 5 INITIAL FIRING INSTRUCTIONS 14 SUBSEQUENT START-UP 15 OPERATING TIPS 17 MAINTENANCE & CLEANING 18 TROUBLESHOOTING 20 DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM 22 Z GRILLS SUPPORT 23 3-Y LIMITED WARRANTY 24 1
WARNINGS! This grill is for outdoor use only. Do not use it in any enclosed area. Do not store or use combustible materials or liquids near this appliance. Keep young children away while it is in use. Maintain a long safe distance between your grill and any combustible. Do not move your grill while operating or while it is hot until the grill is completely cold. If a grease fire occurs, turn “off” and leave lid closed until the fire extinguished. Do not unplug the power cord. Do not throw water on it.
ASSEMBLY INSTRUCTIONS COMPONENT LIST 61 Grease Bucket mm mm mm 4 60 4 61 62 63 1 1 4 Bolt 5/32-32*6 mm Hopper Assembly I Hopper Assembly II Kep Nut 5/32-32 62 5
2.MOUNTING THE BODY FRAME 1.Secure Left Plate(40)on the Platform(50)with1/4-20*12mm Bolt(52). 2.Secure Right Plate(45)on the Platform(50)with1/4-20*12mm Bolt(52). 3.Secure Back Plate(44)on the Platform(50)with1/4-20*12mm Bolt(52) and link with Left Plate(40) and Right Plate(45). 4.Locate the Beam(42) between Left Plate(40)and Right Plate(45) with 1/4-20*12mm Bolt(52). 1.ASSEMBLING OF BOTTOM BASE 1.
3.ASSEMBLING OF HOPPER 5.MOUNTING THE HOPPER TO THE CHAMBER Insert Hopper Assembly I(61) into Hopper Bottom Cover(3), align the holes. Insert the 5/32-32*6mm Bolts(60) through the holes in the Hopper and 5/32-32 Kep Nuts(63), then open the Hopper Lid and tighten it from inside. The four sides are installed in the same way. 1.Remove the Gaskets and Bolts from the Hopper, open the Lid, insert the Hopper into the Chamber, then using these Bolts and Gaskets install it in sequence from inside. 2.
10 7.ATTACHING THE CHAMBER DOOR HANDLE 9.POSITIONING THE DOOR HANDLE Penetrate1/4-20*12mm Hexagon Bolt(53) through Ø18*Ø6.5*2.0mm Gasket(54) and Lid(9) directly to the handle and tighten up. Do not screw over-tight. Align the holes in the Left Door(38) with the holes in the Handle(47). Place a Ø18*Ø6.5*2.0mm Gasket(54) on each 1/4-20*12mm Hexagon Bolt(53) and tight with Wrench. Repeat the former step to assemble the Right Door(46). 8.ATTACHING THE SMOKE STACK AND CHIMNEY CAP 10.
11.POSITIONING THE HEAT BAFFLE 13.POSITIONING THE PORCELAIN GRILL Position The Heat Baffle(5) on the locating brackets which is on the inside walls of the Grill. The notched legs should be facing downward. Position the Porcelain Grill(8)inside the cooking area and locate the Warming Rack(7) on the rack support inside the Chamber. ALLGN WITH SLOTS AND INSERTTO HOLD IN PLACE ALLGN WITH SLOTS AND INSERTTO HOLD IN PLACE 12.POSITIONING THE GREASE DRAIN PAN 14.
INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP Please take attention: If the grill fails to light or the fire in the Firepot goes Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. 2.Open the Pellet Hopper Lid, make sure there are no foreign objects in the Auger and Hopper. 3.
OPERATING TIPS 8.Turn on the grill and turn the Temperature Dial to any setting desired. With the lid closed, preheat the grill for 10 minutes before placing food. 1.Just like other barbecues, the actual temperature of this grill or the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets and so on. 2.Controller Operation 2.
MAINTENANCE & CLEANING Your Z Grills also needs your maintenance. Make sure your grill is OFF and cold completely before performing any maintenance and cleaning. Grease: With long-term use, it caused the accumulation of grease on the Flue Lining, the Grease Drain Tube, the V-shaped Grease Drain and the Grease Drain Pan. Always be sure these grease catch area is clean and free of debris. You should check and clean these area periodically to reduce the risk of fire.
TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Problem Potential Cause Power Fuse Grill does not work properly Hot Rod Control Board Auger Drive Motor Fire goes out How to start 20 Solution Unexpected grill temperature is displayed External Factor Grill temperature is influenced by environmental factors such as high temperature, wind and direct sun. Place unit in shaded area.
DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM RTD SENSOR Z GRILLS SUPPORT Thank you for shopping with us! If you have any question, feel free to contact us or your dealer. Z GRILLS INC. will offer the best technical and sales support in the industry.
Z GRILLS 3 YEARS LIMITED WARRANTY Z Grills Inc guarantees a 3 years warranty of our products from the date of purchase by the original owner against defects in all materials and workman-ship. During the warranty period, Z Grills Inc will at its option repair or replace the defective parts. This limited warranty does not apply to paint, burn pot, grill cover or damage caused from corrosion. Z Grills shall not be liable for transportation charges, labor costs or export duties.