WOOD PELLET GRILLS ZPG - 7002E OWNER’S MANUAL 1-833-947-4557 EMAIL:support@zgrills.com WEBSITE:www.zgrills.
CONTENTS WARNINGS 3 COMPOENT LIST 4 ASSEMBLY INSTRUCTIONS 5 INITIAL FIRING INSTRUCTIONS 13 SUBSEQUENT START-UP 14 OPERATING TIPS 16 MAINTENANCE & CLEANING 17 TROUBLESHOOTING 19 DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM 21 Z GRILLS SUPPORT 22 3-Y LIMITED WARRANTY 23 1
WARNINGS! This grill is for outdoor use only. Do not use it in any enclosed area. Do not store or use combustible materials or liquids near this appliance. Keep young children away while it is in use. Maintain a long safe distance between your grill and any combustible. Do not move your grill while operating or while it is hot until the grill is completely cold. If a grease fire occurs, turn “off” and leave lid closed until the fire extinguished. Do not unplug the power cord. Do not throw water on it.
ASSEMBLY INSTRUCTIONS COMPONENT LIST ITEM Qty Description ITEM Qty Description 61 Ⅰ mm Φ 17 1 Grease Bucket 48 4 Φ 5 Hexagon Bolt (1/4-20*12mm) Φ Φ Hexagon Nut (1/4-20) Gasket( Φ42 . *Φ12 * 10 . mm ) S/S Bolt (5/32-32*5mm) (Φ13*Φ25*2mm) 4 (Φ6.5*Φ15*1mm) 57 16 58 4 Bolt (5/32-32*6 mm) 59 4 Hexagon Kep Nut 60 16 Spring Washer (Φ6.5*Φ10*1.
Lid Assembly: 1.)Using a screwdriver to remove the screws and gaskets that have been assembled in the Chamber. 2).Using the screws and gaskets to assemble the Lid as shown in the original position. Adjust the Lid in the middle position of the Chamber and tighten the screws. 1.Mounting the Body Frame to the Chamber 1.)With the help of another person, put the Chamber on carboard, then attach 2 Left Legs(38) to Chamber(1) with1/4-20*12mm Bolt(46), Φ6.5*Φ10*1.2mm Spring Washer (60) and Φ6.5*Φ10*1.
2.Assembling of Hopper 4. Attaching the Hopper Handle to Hopper Lid Insert Hopper Assembly II(61) into Hopper Assembly I(3), align the holes as shown in FIG 5. Insert the 5 / 32 - 32 * 6 mm Bolts(58) through the holes in the Hopper and 5 / 32 - 32 Hexagon Kep Nuts(59), then open the Hopper Lid and tighten it from inside. The four sides are installed in the same way. Using 5/32-32*5mm S/S Bolt(54) through Φ42* . Φ12 * 10 . mm Gasket(53), and install Hopper Handle to Hopper lid. As Shown.
6. Attaching the Smokestack and Chimney Cap 8.Attaching the Grease Drain Pan Using 1/4-20×12mm Bolt(48) through the holes of Smokestack(15) and the hole of Smoke Stack Gasket(16), Align the hole of Grill body, attaching Φ65 . *Φ18*20. mm Gasket(50) and 1/4-20 Hexagon Nut(52), then using wrench to tighten them, as shown. Attaching the Grease Drain Pan (6) over the Heat Baffle (5) as per direction of below Figure, so that the grease can flow into the Grease Drain Tube, as shown. 13 11 7.
10.Hang on the Grease Basket Hang the Grease Basket(17) on the Grease Drain Tube. As Shown INITIAL FIRING INSTRUCTIONS Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 15 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill. 2.Open the Pellet Hopper Lid, make sure there are no foreign objects in the Auger and Hopper. 3.
SUBSEQUENT START-UP Please take attention: If the grill fails to light or the fire in the Firepot goes out while cooking, it is vital to follow these steps when sufficient pellets are still in the Pellet Hopper. Failure to follow the steps may cause a hazardous “over-firing” of your grill due to an excess of unburned pellets in the Firepot. 1.Turn OFF the appliance and unplug the Power Cord. After the grill cool down, remove all food, the Porcelain Grills, Grease Drain Pan and the Heat Baffle. 2.
OPERATING TIPS 1.Just like other barbecues, the actual temperature of this grill or the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets and so on. 2.It is better to shelter your grill from the wind, this will aid in temperature output, heat retention and heat recovery time when opening the lid. 3.Do not open the lid frequently, it will increase your cooking time. But you can open the lid when you want the grill to cool down quickly. 4.
TROUBLESHOOTING cleaning brush to give the Porcelain-coated Grill Grates a quick brushing when you finish the barbecue. It takes only a minute and it will be ready the next time you want to use the grill. Clean the inner temperature probe after each time use. Ash Clean the ash from the interior of the grill periodically, otherwise excess ash in the firepot may cause your fire to go out, especially in the SMOKE setting. A shop vac is an excellent tool to handle the ash.
DIGTAL THERMOSTAT CONTROL WIRING DIAGRAM Unexpected grill temperature is displayed External Factor Grill temperature is influenced by environmental factors such as high temperature, wind and direct sun. Place unit in shaded area. Open the lid to reduce inside temperature. Excess or discolored smoke Pellets Replace moist pellets with fresh dry pellets.
Z GRILLS SUPPORT Thank you for shopping with us! If you have any question, feel free to contact us or your dealer. Z GRILLS INC. will offer the best technical and sales support in the industry. Please be prepared to provide the following information: Dealer's name, date of purchase Purchaser's name, phone number, address, Z Grills model number, serial number and part identification number from the COMPONENT LIST Please describe your problem accurately so that we can help you figure out.