VISUAL PRESENTER HV-110XG INSTRUCTION MANUAL Please read this instruction manual carefully before using this Visual Presenter and keep it for future reference.
IMPORTANT SAFEGUARDS recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer's instructions, and should use a mounting accessory recommended by the manufacturer. Read Instructions – All the safety and operating instructions should be read before the appliance is operated. Retain Instructions – The safety and operating instructions should be retained for future reference.
Grounding or Polarization – This product may be equipped with either a polarized 2-wire AC line plug (a plug having one blade wider than the other) or a 3-wire grounding type plug, a plug having a third (grounding) pin. The 2-wire polarized plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet.
Damage Requiring Service – Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. When the power-supply cord or plug is damaged.
SA 1965 SA 1966 The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. INFORMATION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
BEFORE YOU USE Use the Visual Presenter under the rated electrical conditions. Do not leave the Presenter under direct sunlight or by heaters, or the Presenter may be discolored, deformed, or damaged. Do not place the Presenter in any humid, dusty, windy or vibrating location. Use the Presenter in the following environmental conditions: Temperature: 0°C~40°C (32°F~104°F) Humidity: 30%~85% (No condensation) Use a soft, dry cloth for cleaning. Do not use any volatile solvent, such as thinner or benzine.
CONTENTS IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 BEFORE YOU USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 2. SETTING UP AND STORING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2-1 SETTING UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2-2 STORING . . . . . .
1.
No. 1 Function Name Camera Head Moving up/down the camera head can change the size of an object in display on the monitor screen smoothly. The shooting area can be moved by tilting the camera head upward, to shoot the image of the lower part of a large document for example. The max. tilting angle is 4 degrees. Note: - The image is distorted to a trapezoid form by tilting the camera head. It is advised that the camera head not be tilted for ordinary use. Max.
13 Zoom Lamp 12 Digital Zoom Button [DIGITAL ZOOM] 14 Gain Button [GAIN] 15 Auto White Balance Switch [AWB] -Normally ON 16 Auto Electronic Shutter Switch [AES] -Normally ON 17 Gamma Value Selection Switch [ -[NORM.] is standard.
No. Name 12 Digital Zoom Button [DIGITAL ZOOM] 13 Zoom Lamp 14 Gain Button [GAIN] 15 Auto White Balance Switch [AWB] 16 Auto Electronic Shutter Switch [AES] 17 Gamma Value Selection Switch [ ] 18 RGB-in Terminal [RGB INPUT] 19 RGB-out Terminal [RGB OUTPUT] Function To operate digital zoom. Use the Digital zoom after moving the camera head to the lowest horizontal position (the minimum shooting area), and the image is expanded even more.
2. SETTING UP AND STORING 2-1 SETTING UP Gently release the clipped area (as marked with arrow) of the right and left stages as illustrated. Note:- It may be damaged by unlatching the stages putting hands on other position not shown by arrows. - When the accessory case is housed inside, be careful not to drop it. Connect the RGB-out terminal [RGB OUTPUT] of the Presenter to the monitor/ projector with the RGB cable (supplied). Note: - Before starting connection, turn OFF the power supply to each unit.
2-3 ZOOMING By moving up/down the camera head, the object in display on the monitor screen can be zoomed-in or zoomed-out. And use the Digital zoom after moving the camera head to the lowest horizontal position (minimum shooting area), and the image is expanded even. But the digital zoom will degrade the image quality. In zoom operation by moving up/down the camera head, focus adjustment is not required (FOCUSFREE).
Belt Pinch the longer end of the belt in the inner part The supplied belt is for preventing the stages from opening unexpectedly. Have it around the presenter folded as shown blow. Unite a piece of Velcro part Belt 3. TROUBLESHOOTING HINTS Symptom No image is on the monitor or project.
4. SPECIFICATIONS General Power voltage Power consumption Outside dimensions Mass Optical Lens Shooting area 12VDC 10.8W 361mm(W)x282mm(D)x161-284mm(H) (14.2in.(W)x11.1in.(D)x6.3-11.2in.(H) (When camera head tilted: 290mm(H)(11.4in.)) 59mm(W)x282mm(D)x161mm(H) (2.3in.(W)x11.1in.(D)x6.3in.(H)) 1.5kg (3.3lbs) F: 2.9, f= 3mm 364mmx271mm (14.3in.x10.7in.) 179mmx135mm (7.1in.x5.3in.
WARNING: Unauthorized recording of copyrighted slide films, materials, photographs, etc. may infringe on the rights of copyright owners and be contrary to copyright laws. ELMO CO., LTD. 6-14, Meizen-cho, Mizuho-ku, Nagoya, 467-8567, Japan OVERSEAS SUBSIDIARY COMPANIES U.S.A. ELMO Mfg. Corp. 1478 Old Country Road, Plainview, NY 11803-5034 Tel : (516)501-1400 Fax : (516)501-0429 E-mail : elmo@elmousa.com Web : http://www.elmousa.com/ Canada ELMO Canada Mfg. Corp.
