[ Put a stop to crime ] Security system and convenience MODEL [ User guide ] 110XV
Limited Consumer Warranty For a period of five calendar year from the date of purchase of this device, Directed Electronics, Inc. promises to the ORIGINAL PURCHASER to repair or replace (with a comparable reconditioned model), free of cost, any electronic control module which proves to be defective in workmanship or material under normal use, SO LONG AS THE SYSTEM WAS SOLD, INSTALLED, AND SERVICED BY A PROFESSIONAL AUTO INSTALLER, AND REMAINS IN THE CAR IN WHICH THE SYSTEM WAS ORIGINALLY INSTALLED.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR ABROAD.
table of contents limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . i standard transmitter configuration . . . . . . . . . . . . . . . . . . . . . . . . . 3 what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 system maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 your warranty . . . . . . . . . . . . . . . . .
rapid resume logic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 power saver mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 programming options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 security & convenience expansions . . . . . . . . . . . . . . . . . . . . . . . 33 glossary of terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 quick reference guide . . . . . . . . . . . . . . . . . . .
standard transmitter configuration controls the Arm and Panic On/Off function. controls the Disarm and Panic Off function. controls Silent Mode™ and Auxiliary channel 2 output. controls the Remote Start function. and pressed together control the Timer mode. and pressed together control Turbo/Short Run. and pressed together control channel 4 output. and pressed together control channel 5 output © 2004 directed electronics, inc.
what is included ➤ A control module ➤ An XHF receiver/antenna ➤ Two four-button transmitters ➤ A Stinger™ DoubleGuard® two-stage shock sensor ➤ A Revenger™ Soft Chirp™ six-tone programmable siren ➤ A status LED indicator light ➤ A push-button Valet® switch ➤ Your warranty registration ➤ A shut-down toggle switch important information Congratulations on the purchase of your combination remote start alarm system.
➜ system maintenance The system requires no specific maintenance. Your remote is powered by a small, lightweight 3-volt lithium battery that will last approximately one year under normal use. When the battery begins to weaken, operating range will be reduced and the LED on the remote will dim. ➜ your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase. Your product warranty will not be validated if your warranty registration is not returned.
➜ caution This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehicle is dangerous and contrary the product's intended use. transmitter functions The receiver uses a computer-based Learn Routine to learn the transmitter buttons. This makes it possible to assign any remote transmitter button to any receiver function.
less than one second before arming or disarming. An optional auxiliary function, such as trunk release, can be controlled by pressing this button for 1.5 seconds.) The auxiliary output controls __________________________. Button The remote start function of your system is controlled by pressing this button twice within 3 seconds. and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously.
using your system ➜ warning! safety first The following safety warnings must be observed at all times: ➤ Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. ➤ When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage).
mode of operation may result in property damage, personal injury, or death. (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user must also have the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear.
UNIT AND SEEK THE ASSISTANCE OF AN AUTHO RIZED DIRECTED D E A L E R T O R E P A I R O R DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. ➜ active arming You can arm the system by pressing of your transmitter for one second. When the system arms, you will hear a short siren sound, or chirp, and see the parking lights flash once. If the power door locks are controlled by the system, the doors will also lock.
down, the siren will chirp to indicate that the system is about to arm. At the 30-second point, the parking lights will flash to indicate that the system is armed. note: If any protected entry point (such as a door or a switch-protected trunk or hood) is open, the system will not passively arm (unless forced passive arming is programmed on. See Programming Options section.) Additionally, each time a sensor is triggered during the arming countdown, the 30-second countdown starts over.
➜ multi-level security arming Multi-Level Security Arming allows you to select which of the system's inputs or sensors will be active and which will be bypassed when the system is armed. (See Table of Zones section of this guide.) Pressing (only in Standard Configuration) again within five seconds of arming the system will activate the Multi-Level Security feature. Each time is pressed again, a different security level is selected.
note: Multi-Level Security Arming only applies to a single arming cycle. Once the system is disarmed and then re-armed, all the zones will be active again. ➜ arming while driving Your security system can be armed while driving the vehicle! Simply press on the transmitter for two seconds while the vehicle is running. The siren will chirp once to indicate that the security system is armed, and then once more to indicate that the ignition is on.
➜ high security disarm This security system offers High Security Disarm. High Security Disarm is a feature that makes it possible to silence and reset the system while it is triggering, without disarming the system. If the system is triggered and the siren has been sounding for longer than six seconds, pressing on the remote transmitter will stop the trigger and return the unit to the armed state. The system will not disarm, but rather reset.
To disarm the security system, turn the ignition to the ON position. Press the Valet button the preset number of times (one to DRW-35 five times) within 15 seconds. After five seconds, the system will disarm. If the system does not disarm, you may have waited too long; turn the ignition off and on and try again.
➜ panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter. Just press for two seconds, and you will enter Panic Mode. The siren will sound and the parking lights will flash for the programmed siren duration. To stop Panic Mode at any time, press on the remote transmitter again. ➜ valet mode You can prevent your security system from automatically arming and triggering by using Valet Mode.
3. Press . 4. Press again. The status LED will light solidly if you are entering Valet Mode, and it will go out if you are exiting Valet Mode. ➜ remote start This feature allows you to remotely start and run your vehicle for a programmable period of time. This makes it possible to warm up the engine, as well as adjust the interior temperature of the vehicle with the climate control system.
med period of time (either 12, 24, or 60 minutes - see Programming Options section of this guide) or until a shutdown input is triggered. important! It is unsafe to operate a vehicle’s motor in a garage or other closed off area. Breathing the exhaust from the vehicle is hazardous to your health. Never activate the remote start in an enclosed space. When you are ready to drive the vehicle: 1. Insert the ignition key and turn it to the ON (not START) position. 2. Press the brake pedal.
➜ valet take-over The Valet® Take-Over feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on. To perform Valet® Take-Over: 1. Before turning off the engine, press and release twice within 3 seconds on the transmitter (or press and release the optional momentary switch).
➜ short-run/turbo Short run turbo mode keeps the engine running after arriving at you destination for a programmable period of 1, 3, 5 or 10 minutes. This allows the system’s timer to conveniently cool down the turbo after you have left the vehicle. To activate: 1. Park the vehicle and set parking brake. 2. Remove your foot from the brake pedal and leave the engine running. 3. Press and release the and buttons at the same time. 4.
active the timer mode will cancel. 1. Press Timer mode buttons. 2. The vehicle will confirm with 4 parking light flashes. 3. A 1-second delay will start. 4. The system will start the car and will run for the specified duration, unless shut down by the remote start button shut down with the remote start button . If the system will remain in timer mode. 5. The system will start every 3 hours until canceled by the brake, hood, or neutral safety shut-down wires.
safety features This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components. ➜ starter anti-grind circuitry Whenever the vehicle is remote started, advanced anti-grind circuitry prevents the starter from engaging, even if the key is turned to the start position. This prevents damage to the starter motor if the key is turned to the start position during remote start operation.
programmed levels. This feature prevents damage to the motor due to fuel delivery system failures or other problems which may cause the engine to race. note: The system uses a wire connected to the vehicle to sense engine speed. This wire must be connected in order for over and under rev protection to work. ➜ shut down inputs This security system uses several inputs to shut down the remote start operation of the motor or prevent remote start if certain inputs are active.
NPC™ ignores, or bypasses, that sensor or switch (along with any other sensors or switches sharing the same zone) for 60 minutes. If the bypassed sensor tries to trigger the security system while it is being bypassed, the 60-minute bypass period will start over. This ensures that a sensor that is continually being triggered will remain bypassed. The vehicle doors are protected by NPC™ differently.
➜ arming diagnostics If the security system is armed at the same time that an input is active (such as a door opening or sensor triggering), you will hear one siren chirp to indicate arming and a second siren chirp to indicate Bypass Notification. A Bypass Notification chirp means that the security system ignores the input that was active when the system was armed, until that input ceases. Three seconds after that input ceases, the security system will resume normal monitoring.
➜ system status chirps The siren will chirp when arming/disarming the system. The pattern of chirps will audibly report the system’s status as described below.
ZONE (Number of LED Flashes) DESCRIPTION 1 Trunk Pin 2 Instant trigger - a heavier impact detected by the shock sensor 3 Door switch trigger 4 Instant trigger - for optional sensors 5 Ignition trigger 6 Hood Pin DEALER-INSTALLED OPTIONS ➜ interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics. If you receive a Bypass notification when arming or a Tamper Alert notification when disarming, look at the LED.
code hopping The receiver and transmitters use a mathematical formula called an algorithm to change their code each time the transmitter is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. This helps to keep the transmitter “in sync” with the control unit even if you use the remote control out of range of the vehicle.
owner recognition Owner Recognition is a revolutionary new feature available only from Directed. Using a Directed Bitwriter, hand-held programming tool, your dealer can program many of the system settings. The programmer makes it possible to program different settings for each transmitter that is used with the system. Then, whenever a specific transmitter is used, the system will recall the settings assigned to that transmitter.
power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet® Mode, after a period of time in which no operation has been performed. This lowers the current draw on the vehicle's battery. Power Saver Mode takes over under the following conditions: ➤ Power Saver when the system is armed: After the system has been armed for 24 hours the LED will flash at half its normal rate, decreasing the system's current draw.
➤ Arming/disarming siren chirps on or off. ➤ The ignition controlled door lock feature on or off: When this feature is programmed on, the doors will lock three seconds after the ignition is turned on, and unlock when the ignition is turned off. If your installer is programming the security system with the Directed Bitwriter, ignition lock and unlock are independent features that can be programmed separately.
➤ Full trigger response 30 or 60 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance. If your installer is programming the security system with the Directed Bitwriter, the full triggered response can be programmed for any duration ranging from 1 to 180 seconds. ➤ Automatic Engine Disable (AED) on or off.
full volume or 6 decibels quieter than the full alarm blast. ➤ The engine can be programmed to run for any duration ranging from 1 to 60 minutes. 12 minutes is the default. After the programmed run time, the engine will shut down and will not restart, unless in Timer Mode. ➤ While the remote start system is running the engine, the parking lights of the vehicle can flash on and off or come on and light steadily.
Field Disturbance Sensor: An invisible dome of coverage is estab- lished by installing the 508D “radar” sensor. Your system can react to any intrusions into this field with the full triggered sequence. Power Locks: This system offers lock outputs that can control some manufacturers' power door lock systems. For other systems, additional parts may be required. Power Trunk Release: The accessory output of the system can op- erate a factory power release for the vehicle’s trunk or hatch.
glossary of terms Control Unit: The “brain” of your system. Usually hidden under- neath the dash area of the vehicle. The control unit houses the microprocessor which monitors your vehicle and controls all system functions. Fault-Proof Starter Interrupt: An automatic switch controlled by your system that prevents the vehicle’s starter from cranking whenever the system is armed.
Trigger or Triggered Sequence: This is what happens when the alarm “goes off ” or “trips.” The triggered sequence of your system consists of the siren sounding and parking lights flashing for the programmed duration. Valet Switch: A small push button mounted at a discretionary location inside the vehicle. It is used to override the starter interrupt when a transmitter is lost or damaged, or to enter or exit Valet Mode.
✂ Arming Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. ■ QUICK REFERENCE GUIDE To arm, press . When the system arms, you will hear a short chirp, and the parking lights will flash once. Arming while driving ■ To arm the system while driving, press on your transmitter while the vehicle is running. The system will chirp once and then once more to indicate that the ignition is on. Disarming ■ To disarm, press flash twice. .
Notes 38 © 2004 directed electronics, inc.
© 2004 directed electronics, inc.
The company behind this system is Directed Electronics, Inc. Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.
