[ Put a stop to crime ] Security system and convenience MODEL [ User guide ] 120XV
limited LL45 consumer warranty For a period of five calendar year from the date of purchase of this auto-security device, Directed Electronics, Inc.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OF PATENTS, IN THE UNITED STATES OF AMERICA AND/OR ABROAD.
table of contents limited LL45 consumer warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i 2-way remote control diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 standard remote configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 what is included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 important information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-way remote control diagram 2 3 1 5 4 8 7 6 standard remote configurations 2 1. Arm/Disarm Indicator (Orange) 2. Receive/Transmit Indicator (Green) 3. Auxiliary Indicator (Yellow) 4. Siren Indicator (Red) 5. Arm Button 6. Disarm Button 7. Panic Button 8. Auxiliary Channel Button © 2004 directed electronics, inc.
what is included ➤ One control module ➤ An XHF2 transceiver/antenna ➤ One 4-button 2-way remote ➤ Stinger® Doubleguard® dual-stage shock sensor ➤ Revenger® Soft Chirp® six-tone programmable siren ➤ In-vehicle status LED indicator light ➤ Push-button Valet® switch ➤ Your warranty registration ➤ Failsafe® Starter Kill ready circuitry (may require additional labor) important information Congratulations on the purchase of your state-of-the-art vehicle security system.
➜ system maintenance This system needs no specific maintenance beyond 2-way remote control battery replacement. The 2-way remote is powered by a 1.5V AAA battery. Low Battery Notification If the battery is low (and this feature is programmed On) the 2-way remote will emit 2 long beeps 5-seconds after a transmission is completed. The 2 long beeps will repeat every 25seconds up to 3 times (or until a 2-way remote button is pressed).
➜ fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Directed Electronics, Inc.
2-way remote control functions The 2-way remote control buttons are used to send commands to the system. The descriptions below reflect the standard configuration for this system. The buttons can be custom configured for the user’s specific needs by the installer. ➜ standard button configurations Button The System Arm and Multi-Level Security Arming functions are controlled by pressing this button for one second.
and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. The auxiliary output controls __________________________. remote operation The remote start system operates at 434 MHz and incorporates Directed’s proprietary XHF2 out-board technology transceiver. The high frequency combined with Binary Data communication achieves superior range with twoway communication.
Alarm Page If the alarm system is triggered while armed, an Alarm Page will be sent to the remote control. When the remote receives an Alarm Page, the LED icons will display the alarm system status information and the remote control will generate beeps. An Alarm Page alert is a series of 10 or 4 rapid beeps and the Red LED will illuminate. This will repeat every 100 seconds to alert the user that the alarm system was triggered and will continue until the alarm page is cleared.
➜ out of range notification If a command is issued from the remote, but the remote is beyond the range of the vehicle to receive the command, the remote responds with 2 sets of 3 quick beeps and the Green LED will flash 6-times. programming 2-way remote To enter programming mode Press and hold all four remote control buttons simultaneously until one long beep is heard. Programming mode is now entered. Beeps On/Off Press to select beeps On/Off.
Page notification The remote control can be programmed to notify the user of a page (audibly beeping if the vehicle’s status changes, e.g. door unlocked, engine started, vehicle violation, etc.). Press to select page On/Off. One beep is page On, Two beeps is page Off. When programmed off the remote will not give any notification that a page was received from the vehicle. To exit programming mode The remote control will exit programming mode after 2-seconds of inactivity and will emit 2 long beeps.
the in-vehicle’s status LED is flashing in groups, see the Diagnostics Section of this guide. This extra chirp is called Bypass Notification. The remote responds to active arming with one beep and the Orange LED will flash 3-times to indicate successful arming of the system. If after 2-seconds the remote beeps once and the Orange and Red LEDs flash 3-times, the system has detected an active sensor that should be checked.
NOTE: If any protected entry point (such as a door or a switchprotected trunk or hood) is open, the system will not passively arm (unless forced passive arming is programmed on. See Programming Options section.) Additionally, each time a sensor is triggered during the arming countdown, the 30-second countdown starts over. When armed your vehicle is protected as follows: ➤ Light impacts trigger the Warn Away® signal. When triggered, the siren chirps and the parking lights flash for a few seconds.
➜ multi-level security arming Multi-Level Security Arming allows you to select which of the system's inputs or sensors will be active and which will be bypassed when the system is armed. (See Table of Zones section of this guide.) Pressing (only in Standard Configuration) again within five seconds of arming the system will activate the Multi-Level Security feature. Each time is pressed again, a different security level is selected.
➜ arming while driving Your security system can be armed while driving the vehicle! Simply press on the 2-way remote for two seconds while the vehicle is running. The siren will chirp once to indicate that the security system is armed, and then once more to indicate that the ignition is on. The system will not respond to any input except the door triggers, and the starter kill relay (if installed) will not be activated.
1. If a sensor triggered the system, the remote will beep 4-times and the Orange and Red LEDs flash 3 times. 2. If a switch (Zone 1, 3, 5, or 6) triggered the system, the remote will beep 4-times, the Orange LED will flash 6-times and Red LED will illuminate for 3 seconds. 3. If the system was triggered so many times that NPC is active the remote will emit the above notifications with 5 beeps instead of 4. ➜ high security disarm This system includes High Security Disarm feature.
NOTES: The first press of the remote button, while the remote is beeping, only clears the alarm page (no command is sent to the vehicle). The transceiver transmits immediately upon system trigger and does not allow disarm during the first 6 seconds after trigger. The 2-way remote will respond with a number of beeps and LED flashes according to whether a pinswitch, sensor, activated the alarm (and also if NPC is active).
important! The unit can be programmed to respond to one to five pulses of the Valet® button for the disarm function. Be sure to check with the installer for the desired programming. The remote will indicate disarm notification with 2 beeps and 3 flashes of the Orange LED. ➜ silent mode To temporarily turn off the arm or disarm chirps, use Silent Mode™. Simply press for less than one second before arming or disarming, and the confirmation chirp(s) will be eliminated for that one operation only.
➜ panic mode If you are threatened in or near your vehicle, you can attract attention by triggering the system with your 2-way remote. Just press for two seconds, and you will enter Panic Mode. The siren will sound and the parking lights will flash for the programmed siren duration. To stop Panic Mode at any time, press on the 2-way remote again. The remote responds with one flash of the Red LED upon entering Panic Mode and two flashes of the Red LED upon exiting Panic Mode.
To enter or exit Valet® Mode using the 2-way remote: 1. Open any vehicle door. 2. Press . 3. Press . 4. Press again. The in-vehicle status LED will light solidly if you are entering Valet® Mode, and it will go out if you are exiting Valet® Mode. The remote responds with the normal arm/disarm notifications with each remote button press. ➜ nuisance prevention® circuitry Your system has Directed’s Nuisance Prevention® Circuitry (NPC®).
NOTE: Arming and disarming the system does not reset this function.The only ways to reset a bypassed zone are for it to not trigger for 60 minutes, or to turn on the ignition. If testing your system, it is important to remember that the NPC® programming can cause zones to be bypassed and appear to stop working. If five chirps are heard when disarming, NPC® has been engaged. If you wish to clear the NPC® memory, turn the ignition key on. NPC® is programmable. See Programming Options section of this guide.
diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. It detects any faulty switches and sensors and prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during your absence. Refer to the System Status Chirps and Table of Zones charts for diagnostic information.
Circuitry has bypassed that zone. The in-vehicle status LED will indicate which zone was involved. (See Table of Zones section of this guide.) The system will retain this information in its memory, and continue to chirp four or five times each time it is disarmed, until the next time the ignition key is turned on. ➜ system status chirps The siren will chirp when arming/disarming the system. The pattern of chirps will audibly report the system’s status as described below.
Zone - Number of LED Flashes Description 1 Instant trigger - often used for hood/trunk pinswitches 2 A heavier impact detected by the shock sensor 3 Door switch trigger 4 For optional sensors 5 Ignition trigger Dealer-Installed Options ➜ interpreting zone diagnostics Warn Away responses are not reported by arming or disarming diagnostics. If you receive a Bypass notification when arming or a Tamper Alert notification when disarming, look at the in-vehicle status LED.
code hopping The receiver and 2-way remotes each use mathematical formulas called algorithms to change their codes each time the 2-way remote is used. This technology has been developed to increase the security of the unit. The control unit knows what the next codes should be. This helps to keep the 2-way remote "in sync" with the control unit even if you use the 2-way remote out of range of the vehicle.
owner recognition Owner Recognition is a feature available exclusively from Directed. Using the Directed Bitwriter, a hand-held programming tool, your dealer can program many of the system settings. The programmer makes it possible to program different settings for each 2-way remote that is used with the system. Then, whenever a specific 2-way remote is used, the system will recall the settings assigned to that 2-way remote.
power saver mode Your system will automatically enter Power Saver Mode while armed or in Valet® Mode, after a period of time in which no operation has been performed. This lowers the current draw to the vehicle’s battery. Power Saver Mode takes over under the following conditions: ➤ Power Saver when the system is armed: After the system has been armed for 24 hours, the in-vehicle LED will flash at half its normal rate, decreasing the system's current draw.
➤ Active arming (only with the 2-way remote) or passive arming (automatic arming 30-seconds after the last door has been closed). ➤ Arming/disarming confirmation siren chirps on or off. ➤ The ignition controlled door lock feature on or off: With this feature on, the doors will lock three seconds after the ignition is turned on, and unlock when the ignition is turned off. The system will not lock the doors when the ignition is turned on with any door open.
NOTE: When the system passively arms after one hour, the entry point that has been left open, and anything connected to the same zone, is bypassed and cannot trigger the system. However, the remaining inputs to the system are fully operational. ➤ Automatic Engine Disable (AED) on or off: The purpose of this feature is to protect the vehicle from being stolen at all times, regardless of whether or not the alarm is armed.
section of this manual for a complete explanation of how NPC® operates. If NPC® is programmed off, the security system will respond to inputs from any sensor indefinitely. NOTE: Because many states have laws regulating security systems, programming NPC® off may cause your system to violate state laws. ➤ Progressive door trigger on or off: When the system is armed and a door is opened, the system responds with ten chirps prior to beginning the full triggered sequence.
installation options The system has many options that may require extra parts and labor. Some of the possibilities are listed here. ➤ Progressive unlocking: In most cars with electric power door locks, the system can be configured so that when the system is disarmed, only the driver’s door unlocks. A second press of the button unlocks the other doors. ➤ Vehicle Recovery System (VRS®): VRS® is an anti-carjacking device designed to help in the safe recovery of your vehicle in case of a carjacking.
Starter Kill, and the VRS® feature to provide the best combination of personal safety and property protection available. When properly installed, the system can never inadvertently stop your vehicle in traffic or on railroad tracks while the vehicle is in operation. It is unlike other systems that shut down your engine while it is running. This system is designed to perform starter interrupt, or starter kill.
NOTE: If the VRS® system is armed while operating the vehicle and not disarmed prior to leaving the vehicle, it is still armed and will trigger the next time the vehicle is driven. ® ➜ vrs triggered sequence Fifteen seconds after the last door has closed, the in-vehicle LED will begin flashing. This delay is intended to allow you time to distance yourself from your vehicle in the event of a carjacking. Forty-five seconds later, the siren begins chirping and the parking lights begin flashing.
➜ disarming the vrs® Take the time to familiarize yourself with the VRS® triggering sequence and the disarm procedure. It is important to recognize and identify the VRS® trigger sequence and know how to disarm it in case of accidental activation. Once the VRS® is armed, it does not disarm automatically. You must disarm it the next time you operate the vehicle. You must disarm it with one of the following procedures: If the system has not entered the triggered sequence (siren has not started chirping): 1.
NOTE: If the VRS® system has begun its chirping sequence, the ignition must be turned off, then on to disarm. If you are driving the vehicle at the time, pull to a safe place away from traffic and follow the triggered sequence disarm procedure. glossary of terms 2-Way Remote: Hand-held, 2-way transceiver which operates the various functions of your system. Control Unit: The "brain" of your system. Usually hidden under the dash area of the vehicle.
Shock Sensor: This is a sensor mounted in the vehicle that is designed to pick up impacts to the vehicle or glass. Siren: Noise generating device usually installed in the engine compartment of the vehicle. It is responsible for generating the "chirps" you hear, as well as the six tones you hear while the alarm is triggered. Trigger or Triggered Sequence: This is what happens when the alarm "goes off" or "trips".
security & convenience expansions Here we have listed only some of the many expansion options available. Please contact your dealer for a complete explanation of all the options available to you. Audio Sensor: Metal on glass, glass cracking, and breaking glass each produce distinctive acoustic signatures. The 506T audio sensor uses a microphone to pick up sounds, and then analyzes them with proprietary acoustic software to determine if the glass has been struck.
Power Window Control: Automatic power window control is provided with the 529T and 530T systems. Mobile Video: This system is compatible with Directed Video’s MCB1000 Multi-Channel Controller, featuring on-screen security system programming and zone trigger information. Valet® Start System: For the ultimate in convenience, the Valet® start system can start your vehicle, monitor engine functions, and power your climate control system with a push of a button.
✂ QUICK REFERENCE GUIDE To arm using your 2-way remote Cut along dotted line and fold for a quick and easy reference to keep in your purse or wallet. ➤ You can activate, or arm, the system by pressing on your remote for one second. When the system arms, you will hear a short siren sound, or chirp, and the parking lights will flash once. If the vehicle’s power door locks have been connected to the system, the doors will lock. To disarm using your 2-way remote ➤ To disarm the system, press .
The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology, Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.
