Model 410 Owner's Guide
Limited Lifetime Consumer Warranty Directed Electronics, Inc.
THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DEI OR ITS SUBSIDIARY, THE PROPER VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DEI SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DEI DEALER'S PURCHASE PRICE OF THE UNIT.
Table of Contents Limited Lifetime Consumer Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i Standard Configuration Transmitter Diagram . . . . . . . . . . . . . . . . . . . . . . . . . 2 What Is Included . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FCC/ID Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 © 1999 Directed Electronics, Inc.
What is Included ■ The control module ■ A pair of four-button transmitters ■ The red status LED indicator light ■ A push-button Valet® switch ■ Your warranty card ■ Failsafe® Starter Kill ready circuitry (may require additional labor) Important Information This system has been designed to provide years of trouble-free operation. Due to the complexity of this system, it must only be installed by an authorized dealer.
FCC/ID Notice This device complies with Part 15 of FCC rules. Operation is subject to the following conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. System Maintenance The system requires no specific maintenance.
Transmitter Functions Your vehicle keyless entry system is programmable, making it possible to assign any transmitter button to any specific receiver function. The transmitter initially comes programmed with Standard Configuration, but may also be customized by an authorized dealer. The buttons in all of the instructions in this manual correspond to a Standard Configuration transmitter. Button The arming/locking function is controlled by pressing .
and Buttons An optional auxiliary convenience or expansion function that you have added to your system can be activated by pressing these buttons simultaneously. The auxiliary output controls _____________________________. Using Your System Arming/Locking Pressing for one second arms the system and locks the doors. The red LED will begin to flash once per second. The Failsafe® Starter Kill will prevent the vehicle’s starter from cranking if it has been installed.
grammed for passive mode, it will automatically activate the Failsafe® Starter Kill relay 30 seconds after the ignition is turned off. Passive mode is indicated by rapid flashing of the LED after the ignition is turned off. NOTE: For passive mode to be effective, the Failsafe® Starter Kill relay must be installed. If passive mode is programmed on, it is also possible to program the system to lock the doors automatically. This is called passive locking.
This feature allows you to override the Starter Kill without the transmitter should it be lost, damaged or disabled. To do this, you must have the vehicle's ignition key and know where the Valet® switch is located. Check with the installer for the location of the Valet® switch. Turn the ignition to the "run" position. Press and release the Valet® switch, within 10 seconds. The LED will stop DRW-35 flashing and the vehicle should start. If it does not, you may have waited too long.
To enter or exit Valet® Mode with the Valet switch: Turn the ignition on and then off. Press and release the Valet switch within 10 seconds. The status LED will light steady if you have entered Valet Mode. To exit Valet Mode, repeat the steps above. The LED will turn off when exiting Valet Mode. If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter! Just press and you will enter Panic Mode.
Programming Options Programming options control what your system does during normal operation, and require little or no additional parts. However, some may require additional installation labor. The following is a list of program settings, with the factory settings in Bold: ■ Passive mode or active mode. In passive mode the Failsafe Starter Kill relay will be automatically activated 30 seconds after the ignition key is turned off.
Owner Recognition Owner Recognition is a feature available exclusively from DEI®. Using a DEI® Bitwriter hand-held programming tool, your dealer can program many of the system settings. The programmer makes it possible to program different settings for each transmitter that is used with the system. Then, whenever a specific transmitter is used, the system will recall the settings assigned to that transmitter.
Valet® Start System: For the ultimate in convenience, the Valet® Start System can start your vehicle, monitor engine functions, and power your climate control system with a push of a button! Overrev protection, open-hood lockout, brake-pedal shutoff, and automatic timer shutoff are all included. This option is available only for automatic-transmission, fuel-injected gasoline vehicles. Power Window Control: Power window control is provided with the 529T or 530T systems.
Glossary of Terms Control Unit: The “brain” of your system. Usually hidden underneath the dash area. It houses the microprocessor which monitors your vehicle and controls all of the alarm’s functions. Failsafe® Starter Kill: An automatic switch controlled by the security system that prevents the starter from cranking whenever the system is armed. The vehicle is never prevented from cranking when the system is disarmed, in Valet® mode, or should the starter kill switch itself fail.
■ Pressing for one second will arm the system and lock the doors. The red LED will begin to flash once per second. The Failsafe® Starter Kill will prevent the vehicle’s starter from cranking if it has been installed. The vehicle’s horn (if connected) will honk and the parking lights will flash once to confirm arming of the system. To disarm/unlock using your remote ■ To disarm the system and unlock the doors, press for one second.
The company behind this system is Directed Electronics, Inc. Since its inception, DEI® has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology, DEI is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world. Call (800) 274-0200 for more information about our products and services.
