Responder LE Model 5301 Remote Start Keyless Entry Owner’s Guide © 2008 Directed Electronics, Vista, CA G4202V 2008-05
Contents Government regulations......................................................................................5 Warning! Safety first..........................................................................................6 What’s included.................................................................................................9 Important information.........................................................................................9 Your warranty.........................................
Government regulations This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
This device complies with the Industry Canada Radio Standards Specification RSS 210. Its use is authorized only on a no-interference, no-protection basis; in other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device must accept any radio interference that may be received, even if this interference could affect the operation of the device.
Before remote starting a manual transmission vehicle, be sure to: • Leave the vehicle in neutral and be sure no one is standing in front or behind the vehicle. • Only remote start on a flat surface • Have the parking brake fully engaged Warning! It is the responsibility of the owner to ensure the parking/ emergency brake properly functions. Failure to do so can result in personal injury or property damage.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS.
What’s included • • • • • • • One five-button/2-way Supercode Responder LE remote control One five-button/ 1-way Supercode remote The control module (installed out-of-sight) Control center with integrated status LED and Valet override switch A remote start defeat toggle switch Window decals Your warranty registration Important information Congratulations on the purchase of your state-of-the-art remote start and keyless entry system.
Responder LE 2-way remote 6 8 1 2 9 7 3 4 AUX 5 Feature Description 1 Lock button Press for one second to lock. 2 Unlock button Press for one second to unlock. 3 Remote start button Press for one second to activate remote start. 4 Auxiliary button Press and hold for 1.5 second to activate optional trunk release. 5 Function button Allows access to programming and modifies operation of the other buttons. 6 Label Back of remote has label to identify the remote as 2-way or 1-way.
1-way companion remote 6 8 1 2 7 3 4 5 AUX Note: See call-out table for 2-way ➤ Transmitter configuration AUX Level Direct Access x1 AUX AUX x2 AUX x3 x4 Button Lock Silent Lock Unlock Silent Unlock Valet Mode Car Finder Remote Start Reset Timer Mode Smart Start AUX Runtime Rear Defogger AUX AUX AAUUXX Trunk Release AUX 1 AUX 2 AUX 3 Function Shift* Cabin Lock Status* Runtime Temperature (2-way only) Check* request* (2-way only) (2-way only) * button must be pr
Button Lock Unlock AUX AUX Remote Start AUX AUX AUX Command: Feedback: Notes: Press one time to Lock Command: Feedback: Notes: Press one time to Lock Command: Feedback: Notes: Press one time to activate Remote Start Command: Press and hold for 1.5 seconds to activate the Trunk Release. Feedback: The AUX LED turns on for 3-secs and AUX activation tone Lock LED flashes for 1-sec with 1 beep. Press/hold for 1.
Feature List: Silent lock AUX Command: Press one- time and then press Feedback: Lock LED flashes for 1-sec Notes: Locks the system without horn honks* Silent unlock AUX AUX Command: Press one- time and then press . Feedback: Unlock LED flashes for 1-sec Notes: Unlocks the system without horn honks* AUX Runtime reset AUX Command: Press one-time and then . Feedback: Remote start On tones sound. Notes: Re-starts the remote start runtime counter if remote start is active.
Valet mode AUX Command: Press two-times and then . Feedback: Remote beeps 1 to 2 times when entering Valet mode. Notes: To enter or exit Valet mode, even if Locked. When entering Valet Mode the remote beeps one-time. When exiting Valet Mode the remote beeps two-times. AUX Timer mode AUX Command: Press two-times and then . Feedback: Remote start LED turns on. Notes: Enables or disables the remote start timer mode. Aux 2 AUX Command: Press two times and then press .
Aux 3 AUX Command: Press three times and then press . Feedback: The AUX LED turns on for 3-secs, AUX activation tone sounds. Notes: This is an optional feature. See your sales rep/installer for details. AUX Runtime check AUX Command: Press three-times, and then Hold for 1.5 seconds. Feedback: Remote start On tones sound. Notes: Runtime remaining is displayed as per the LED on the remote. (See page 23). If the remote start is not active the 2-way responds with an error tone.
➤ Out of range notification If a command is issued from the remote, but the remote is beyond the range of the vehicle to receive the command, the remote will respond with an out-of range notification. If this occurs, the transmit indicator on the remote flashes rapidly, the key LED turns on, and the remote emits the error tone sounds. Since conditions will vary in different areas (i.e.
➤ Remote control programming The Responder LE 2-way remote control has menus for programming the remote to the system control module and for configuring the remote control user features. Before you start make sure the keypad is unlocked. (See page 11) AUX To program the remote user features: 1. Press and hold the button on the remote for 12 seconds. (ignore the car indicator at 3 seconds). The remote emits one long beep, and the transmit LED turns on to indicate the Main Menu. 2.
1 2 Off. If the keypad lock is On, press , and then press to unlock the keypad. Note: If the auto keypad lock feature is programmed On, the remote unlocks when the vehicle ignition is turned Off. The remote stays unlocked to allow time to exit and unload the vehicle, and then lock the doors with the remote. When the button is pressed, the keypad auto lock feature resumes normally. 2 3 Press the • • • AUX button to access and change the Remote Beeps feature.
the optional factory alarm trigger pages. Note: If a remote button is not pressed for more than 72 hours, the remote automatically goes into sleep mode to extend battery life. It wakes up and resets each time a button is pressed. ➤ Multi-car control capability You can use the Responder LE 2-way and 1-way companion remote control system for two cars, with full command capability for both vehicles.
➤ Locking the vehicle To lock the vehicle, press the button on the remote control. The horn in the vehicle “honks” one-time, and the parking lights flash one-time. If the power door locks have been connected, the doors lock. The system automatically checks for errors when it locks. The 2-way remote honks one-time and then flashes the LED indicator to confirm locking. If no lock confirmation is received, the remote emits the out-of-range signal.
out-of-range signal. ➤ Overriding the optional starter kill To bypass the optional starter kill without a remote control: Use your override switch located on the control center (see diagram below) to bypass the system. This switch bypasses the system only if you have the vehicle key. To check proper operation: 1. 2. While the vehicle is locked, open the door. Immediately insert the key into the ignition and turn it to the Run or On position.
Using the remote start Read this user guide, including the warnings on page 6, before using the remote start. Ensure that the vehicle is parked in an open area, not in a garage. To use your remote start to pre-warm or pre-cool your vehicle, remember to set the climate controls to the desired settings before shutting Off the engine. ➤ Remote starting your vehicle • • Press the button on the remote control. The vehicle parking lights flash.
➤ Runtime check Your system has a feature (if programmed on) that automatically notifies you when the run time is getting low. The default runtime is 12 minutes. To check the amount of runtime remaining: After the vehicle is remote started, press the button three-times and then hold until the remote beeps, and then release. The LEDs light up to indicate how much time is remaining.
➤ Manual transmission vehicles If the vehicle has manual transmission the proper steps must be followed before leaving the parked vehicle, or the remote start feature is disabled. This process is called MTS, manual transmission start. 1. 2. 3. 4. 5. 6. 7. 8. 9. While the vehicle is running, put the transmission in neutral. Press the vehicle’s foot brake. Apply the emergency brake. Release the vehicle’s foot brake. Note: Pressing the brake again after this step will disable the remote start feature.
➤ Timer mode This unit can be programmed to start and run the engine every three hours, for a maximum of six cycles. The engine will run for the programmed run time and then shut down. After three hours, the system will restart the engine. Important: Timer Mode should be used in open areas only. Never start and run the vehicle in an enclosed space such as a garage or carport. To activate timer mode with an automatic transmission: 1. Remote start the vehicle by pressing twice and then press . 2.
To exit timer mode without the transmitter: 1. 2. Make sure the remote start system is not operating the engine. Turn the ignition on. Timer Mode is exited and the parking lights flash slowly four times. Note: The Bitwriter can change the amount of times the remote start activates and, it can change the intervals between activations in timer mode. ➤ Turbo timer mode To activate turbo timer mode: 1. 2. 3. Make sure turbo timer is turned on. Open the vehicle door.
To enter turbo timer mode with a manual transmission: Perform the manual transmission procedure with the door open. Transmit the timer mode feature with the remote by pressing two-times, and then press . AUX After exiting the vehicle, lock the system and the vehicle remains running for the programmed runtime. (The remote start feature is still enabled). You can still remote start the vehicle after the turbo timer has timed out and shut Off the vehicle.
To activate Smart Start mode: • Press the button on the remote 3 times and then press the button. AUX The 2-way remote beeps once, and flashes the remote start LED once. The parking lights flash 5 times fast to confirm the remote is in Smart Start mode. To activate Smart Start mode with a manual transmission: 1. 2. 3. Enter the MTS procedure. Exit the vehicle and press the button on the remote (the vehicle shuts down when locking). Press the button on the remote 3 times and then press the button.
➤ Cabin temperature Using the Responder LE you have the ability to check the temperature inside the vehicle. Press the button one-time and Hold it until the remote beeps, and then release. The LEDs light up indicating the temperature range of the vehicle. 95˚F and above 76˚F to 95˚F 56˚F to 75˚F 32˚F to 55˚F AUX 32˚F and below ➤ Turning on the rear defogger The rear defogger (if connected) is programmed to automatically activate when remote start is turned on.
➤ Valet take-over The Valet take-over feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you want to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on. To perform Valet take-over: 1. 2. 3. Before turning Off the engine, press and release the button on the transmitter within 3 seconds.
Safety features This system has several important safety features to ensure proper operation of the motor and prevent accidental damage to the engine or its components. ➤ Optional starter anti-grind circuitry Whenever the vehicle is remote started, advanced anti-grind circuitry prevents the starter from engaging, even if the key is turned to the start position. This prevents damage to the starter motor if the key is turned to the start position during remote start operation.
Diagnostics The micorprocessor at the heart of the system is constantly monitoring the switches that are connected to the main unit. ➤ Locking If the system is locked at the same time that the door input is active, you will hear one horn honk to indicate locking, and then a second horn honk to indicate Bypass Notification.
➤ Remote start This system can provide you with information to indicate what the problem is when using the remote start. When the remote start is activated and fails to engage, count the parking light flashes to determine the problem. The parking lights will flash between 5 - 8 times to indicate what caused the no start situation.
Owner recognition Owner recognition lets up to four users of the system have unique settings to meet their specific needs. It is almost like having four separate systems in your vehicle, one for each user. This feature is only available to authorized dealers using the Bitwriter or Bitwriter 2 program tool. Rapid resume logic This Directed system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory.
➤ 2-way remote Your Responder LE 2way remote control has a feature called remote power save mode. When programmed On under remote options, the remote conserves power by disabling the paging function if unused for more than 72 hours. Pressing any button on the remote restores the paging function. The default setting is On. See Remote control programming section of this guide or ask your dealer for details on how to program. Programming options Your system has many custom programmable options.
Convenience expansions Listed below are some of the expansion optins available. Please consult your dealer for a complete explanation of all the options avaiable to you. Power Trunk Release: The accessory output of the system can operate a factory power release for the vehicle’s trunk or hatch. Sometimes an optional relay is required. If the factory release is not power-activated, Directed®’s 522T trunk release solenoid can often be added.
Glossary of terms 2-Way Remote: A hand-held, remote control which operates the various functions of your system and receives feedback and pages from the system. Control Center: The control center contains the system’s radio-frequency antenna, the valet and override switch, and the Status LED. For maximum remotecontrol range, the Control Center is usually located at the top of the windshield, centered near the rear-view mirror. Control Module: The “brain” of your system.
© 2008 Directed Electronics. All rights reserved.
✂ Quick reference guide 1 • Locking To lock press The lock LED flashes and the remote beeps one-time. If horn honk is installed, the remote emits a honk sound. Cut along the dotted line and fold to keep in purse or wallet for a quick and easy reference. 2 • Unlocking To unlock press . The unlock LED flashes for one-second, and the remote beeps two-times. • Bypassing the optional starter kill without a remote 3 4 5 AUX Turn on the ignition. Press and release the Valet button within 15 seconds.
• To disable the remote start system Move the shutdown toggle switch to the Off position. 1 Location of Shutdown Toggle Switch___________________ • 2 Valet Mode Press two-times and then . The unlock and funtion LEDs blink and the remote beeps once. When valet mode is Off, the remote beeps two-times. 3 4 • 5 Before turning Off the engine, press and release the 6 within 3 seconds. Then wait a few seconds. Valet take-over 1. button Turn the ignition key to the Off position.
Limited lifetime consumer warranty Directed Electronics.
WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE.
The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology. Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.
