Intelliguard 750 Owner’s Guide
limited lifetime consumer warranty Directed Electronics, Inc.
LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State.
contents limited lifetime consumer warranty . . . . . . . . . . . . . . . . . . . . .i trademarks and copyrights . . . . .ii what is included . . . . . . . . . . . . . .2 important information . . . . . . . . .2 system maintenance . . . . . . . .3 your warranty . . . . . . . . . . . . .3 fcc/id notice . . . . . . . . . . . . . . .3 remote configurations . . . . . . . . .4 remote functions . . . . . . . . . . . . .5 standard configuration . . . . . . .5 using your system . . . . . . . . . . . . .6 arming . .
what is included z Intelliguard control module and harness z Two five-button remotes z Presentation envelope and quick reference card z Two window decals z XHF antenna/receiver with harness z Pre-wired blue status LED z PlainView 2 Valet® button z 518C neo-siren z 506T audio sensor z Digital dual-zone omnisensor important information Congratulations on the purchase of your state-of-the-art vehicle security system. It has been designed to provide years of trouble-free operation.
system maintenance The system requires no specific maintenance. Your remote is powered by a miniature 3V lithium battery that will last approximately one year under normal use. When the battery weakens, operating range will be reduced and the system will provide a low battery warning chirp indication when disarming. your warranty Your warranty registration must be completely filled out and returned within 10 days of purchase.
remote configurations Remote Start or Accessory Output Button Silent Arm/Disarm or Accessory Output Button Arm/Disarm and Panic Button Trunk Release or Optional Accessory Channel Button Shift Button note: This manual describes the features and accessories that are included with your system along with information about compatible Clifford accessories that are not included. For a list of included accessories, please refer to the What Is Included section of this manual.
remote functions This system uses computer-based code learning to learn the remote buttons. This makes it possible to assign any remote button to any system function. The remote initially comes programmed with standard configuration, but may also be customized using the CliffNet Wizard PC program. The buttons in all of the instructions in this manual correspond to a standard configuration remote. standard configuration Button The arming, disarming, and panic function are controlled by this button.
Button, then Button Accessory C output is controlled by these buttons. Button twice, then Button These buttons active remote Valet®. Button twice, then Button These buttons disable the sensors. Button twice, then Button These buttons enter safe start mode for manual transmission vehicles and activate Autostart mode. Button three times, then Button These buttons adjust the dual-zone omnisensor. Button three times, then Button These buttons adjust the dual-zone radar sensor.
arming You can activate, or arm, the system by pressing on your remote for one second. When the system arms, you will hear two short siren sounds, or chirps, and see the parking lights flash twice. The LED will begin to flash steadily. If the vehicle’s power door locks have been connected to the system, the doors will lock. While the system is armed, the LED status indicator will flash approximately once per second showing that the system is actively protecting your vehicle.
When armed, your vehicle is protected as follows: z The LED will flash as a visible theft deterrent. z Light impacts will trigger the Warning Zone signal. When triggered, the siren will sound for a few seconds. z Heavy impacts will trigger the system. The triggered sequence is 30, 60, or 90 seconds of constant siren sounding and flashing parking lights. z If a protected entry (door, hood, or trunk) is opened, the system will immediately trigger the siren and flash the parking lights.
the installer for the location of the PlainView 2 Valet® button. Please refer to the Disarm/Valet® Mode section of this guide for instructions to enter the pin code. remote siren silencing This system offers remote siren silencing. Remote siren silencing is a feature that makes it possible to silence and reset the system when it is triggering without disarming the system.
remote sensor disable To temporarily disable a sensor input, arm the system, press twice and then . The lights will flash four times and all warn away trigger zones one, two, three, and eight are bypassed. Press the buttons again; the lights flash four times and both warn away and full trigger zones one, two, three, and eight are bypassed until the system is disarmed. This can be performed anytime the system is armed. 1. Arm the system. 2. Press 3.
auxiliary channel bypass Alarm sensor input zones one, two, three, and eight will be bypassed while a pulsed or timed auxiliary Output is active. panic mode with smart door locking If you are threatened in or near your vehicle, you can attract attention by triggering the system with your remote! Just press for two seconds to enter Panic Mode. The siren will sound and the parking lights will flash for the programmed duration.
3. After the last digit of the pin code is entered: a. To disarm the system: press and release b. To enter valet® mode: Press and hold . for three seconds. The LED status indicator will light steadily if you are entering Valet® Mode and will turn off if you are exiting Valet® Mode. To exit Valet® Mode: 1. Turn the ignition on. 2. Enter PIN code. 3. After the last digit press for one second. The LED will turn off. remote valet® mode The operations described in this section refer to remote buttons.
one-time auto-arming bypass This will bypass the auto arm feature once only. 1. With the key, turn the ignition on, then off within two seconds. 2. The siren will chirp once to confirm auto arming bypass. 3. The system will not auto arm. note: The system will revert to normal auto arming when the system sees the ignition on for at least three seconds.
the ignition is turned on. For more information, please refer to the Table of Zones section of this guide. false alarm control technology (FACT II) Your system offers FACT II, a feature that prevents annoying repetitive trigger sequences due to a faulty sensor or environmental conditions such as thunder, jackhammers, airport noise, etc. Here’s how it works: The alarm triggers three times.
select siren sounds To customize siren sounds, please refer to the selectable siren sounds feature in the User Selectable Features grid. Once in programming mode, press on the remote to begin playback of the available sounds. Press on the PlainView 2 Valet® button while playing the desired sound to add that sound; press while playing the desired sound to delete that sound.
interior light exit delay, and you arm the system before the interior light goes out, you may hear Bypass Notification chirps. Once the light shuts off, however, the doors are monitored normally. disarming diagnostics Extra disarm chirps are the Tamper Alert. If three chirps are heard when disarming, the system was triggered in your absence. If three chirps are heard, the LED status indicator will indicate which zone was involved when you turn the ignition on (see the Table of Zones section).
table of zones The zone number is the number of LED flashes used by the system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. If the Warning Zone response is triggered, the LED will not report it.
high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory.
z Power Saver when the system is armed: After the system has been armed for 48 hours, the LED will flash at half its normal rate, decreasing the system's current draw. z Power Saver in Valet® Mode: When the system enters Valet® Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet® Mode, the LED will shut off.
allows the vehicle's doors to lock when the security system passively arms (after the 30 second countdown). This feature only works if passive arming has been programmed. z Panic mode enabled/disabled: Some states have laws against siren capability while driving. z Full trigger response 30, 60, or 90 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance.
cliffnet wizard installation software programming Cliffnet Wizard provides access to all available system features and some that are not available when manually programming with the Valet® button. Cliffnet Wizard is compatible with Microsoft Windows 95/98/2000/ME/XP/NT so most programming operations can be accomplished by pointing and clicking with a mouse. This eliminates the need for programming grids and lengthy programming sequences.
5. Feature select - Press the same number of times as the desired feature. The siren will chirp with each press. The feature can now be changed using the remote control. 6. Feature change - Press on the remote. If the system chirps once, the feature has just turned off; if the system chips twice, the feature has just turned on. If the feature has more than two settings, continue pressing on the remote to toggle through the settings.
user selectable features The factory default settings are shown in bold.
user selectable features descriptions - column one add new remote (auto learn) Auto-learn new five-button Radar2 remote controls to the system in the standard button configuration. Once you have entered the feature, press on the remote until you hear a confirmation chirp. Press again until you hear two chirps indicating the new remote is learned. auto (passive) arm - off/on z Off: The remote must be used to arm the system.
auto unlock - off/ignition z Off: The doors will not automatically unlock when the ignition is turned off. z Ignition: The doors will automatically unlock as soon as the ignition is turned off. auto (passive) arm and lock - off/on z Off: The doors will not lock when the system passively arms. z On: The doors will lock when the system passively arms. This feature only applies when passive arming is programmed on.
user selectable features descriptions - column two set pin code This feature allows the setting of the user's personal PIN code. For more information, please refer to the PIN Programming section of this guide. select siren sounds The individual sounds the siren produces during an full trigger alarm can be customized for owner recognition of an alarm trigger. For more information, please refer to the Select Siren Sounds section of this guide.
reset to default settings All system settings (except PIN and remote programming) in the User Programming grid will be reset to their default factory setting as indicated in bold lettering. z Press the arm/disarm button of the TX; the siren will chirp twice as confirmation. panic off/on z Off: The panic feature is not available. z On: The panic feature is available. auto start setting - off/battery only/temp only/battery and temp note: This feature is only available with the IntelliStart option.
user selectable features descriptions - column three The features in this column pertain to programming individual remote channels in custom configurations. Following is an explanation of the features. arm/disarm only The remote control channel programmed into this feature will arm/disarm the system only. note: When programming a new remote control to custom configuration a channel must first be programmed to this feature before programming the remaining channels.
remote start z This feature is only available with IntelliStart connected. z The remote channel programmed into this feature will activate or shut down the Intellistart remote start system. window control z This feature is only available with SmartWindows connected. z The remote channel programmed into this feature will activate the vent or roll down feature of the SmartWindows system. accessory c output The remote channel programmed into this feature will activate the accessory output.
pin programming A PIN code can have one to four digits; each digit can be from 0-9. note: A PIN code cannot begin with a zero. Programming Procedure 1. Enter the feature location in the installer programming grid. 2. Immediately press and release 3. Select each digit by pressing of the PlainView 2 Valet button. 1-9 times, and then press to enter the number into the system. To enter a zero, press only. 4.
PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set. 1. Turn on the ignition. 2. Enter the new PIN code. 3. Press and hold for three seconds. z LED turns on: New PIN code is learned and programming is complete. z LED stays off: New PIN code is not learned and the system reverts to the old PIN code. Redo the programming sequence.
Disarming auto-immobilization To disarm auto-immobilization when active, follow any of the sequences listed below. z Turn ignition on and press the arm/disarm button. z Arm the alarm and then disarm the alarm. z Turn the ignition on and enter the system valet®/PIN code. one-time valet feature This feature allows the system to be put in valet mode only until the next time the ignition is turned on. ON: Valet mode will be exited every time the ignition is turned on.
the engine, stranding the thief and vehicle. At this time your remote will not operate the system, only you can turn off the BlackJax by entering your secret PIN through the PlainView 2 valet button. blackjax activation sequence When BlackJax is programmed ON, BlackJax sequence will begin every time the ignition is turned on and must be turned off by entering your PIN code. It will then activate again while driving when triggered as described below.
5. If PIN code is NOT entered within 20 seconds: z System sounds siren and begins flashing parking lights. z Brake lights continue to flash. z The system will now immobilize as described in steps 6-7. 6. If system sees the engine speed return to 1 ½ times idle or lower, the system will immobilize the vehicle as described in step 7. 7. Vehicle Immobilization: z Immobilizer will engage the starter and ignition circuits.
Bypass BlackJax temporarily 1. Turn ignition on. 2. Enter PIN code. Do not enter valet or programming mode. 3. Within 10 seconds press 4. Siren chirps 1 time as confirmation of BlackJax bypassed. 5. Turn Ignition Off, siren chirps 3 times as confirmation of exiting programming. . note: If ignition remains on after entering PIN code and no action for 10 seconds, unit will automatically exit programming mode without chirps. To return to normal BlackJax Operation 1. Turn ignition on. 2.
audio sensor The 506T Audio Sensor is a low-current device that provides an added level of protection to an existing security system by detecting sounds that have the acoustic signature of breaking glass or metal-to-glass impacts. adjusting the omnisensor The Omnisensor is designed for ease of adjustment by the user and to give the ultimate in impact detection without the possibility of false triggers that are common with less sophisticated sensor.
4. 5. 6. 7. 8. Adjust Primary zone z Press z Siren chirps 2 times. z Sensor adjustment mode is entered. z Hit vehicle at the desired level of impact. z Sensor adjusts itself to the force of Hit. z Siren chirps 1 time as confirmation of adjustment. z Press of the remote control. of the remote control to lock adjustment. To enter Warn-away zone adjustment z Press z Siren chirps 1 time. z Warn-away zone adjustment is entered. .
z Primary zone can now be re-adjusted as described in step 4. z Or press z The siren will chirp 3 times when sensor adjustment mode has been exited. again to exit programming mode. note: You must wait 15-seconds for the Omnisensor to become active after arming. glossary of terms Control Unit: The "brain" of your system. Usually hidden underneath the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all of the system's functions.
Omnisensor: A dual-zone learning impact sensor. PlainView 2 Valet Button: A small two-button switch mounted some- where inside the vehicle. It is used to override the alarm when a remote is lost or damaged, or to enter or exit Valet mode. Siren: Noise generating device usually installed in the engine compart- ment of the vehicle. It is responsible for generating the "chirps" you hear, as well as the six tones you hear while the alarm is triggered.
security & convenience expansions Here we have listed only some of the many expansion options available. Please contact your dealer for a complete list of all the options available to you. Backup Battery: The 520T keeps the system armed, triggers the alarm and keeps the immobilization circuits active if main battery power is disconnected. Power Trunk Release: The button can operate a factory power release for the vehicle’s trunk or hatch. (An optional relay may be required.
health check Directed Electronics recommends you return to your installing Clifford dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. note: There may be a small charge incurred for this service. © 2 0 0 4 d i re c t e d e l e c t ro n i c s , i n c .
The company behind this system is Directed Electronics, Inc. Since its inception, Directed® has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, Directed® is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.
