Arrow 5 Owner’s Guide
limited lifetime consumer warranty Directed Electronics, Inc.
LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State.
table of contents limited lifetime consumer false alarm control technology warranty . . . . . . . . . . . . . . . . . . . . .i (FACT II) . . . . . . . . . . . . . . . . .13 trademarks and copyrights . . . . .ii select siren sounds . . . . . . . . . . .14 table of contents . . . . . . . . . . . . .1 diagnostics . . . . . . . . . . . . . . . . . .15 what is included . . . . . . . . . . . . . .2 important information . . . . . . . . .3 your warranty . . . . . . . . . . . . .3 fcc/id notice . . . . . .
transmitter configurations Arm/Disarm Button Accessory Output Button Optional Accessory Channel Button what is included 2 z Arrow 5 control module and harness z Two three-button transmitters z XHF antenna/receiver with harness z Pre-wired blue status LED z PlainView 2 Valet switch z 504C dual-stage shock sensor with harness z 514C neo-siren z Presentation pack z Quick reference card z Two window decal's
important information Congratulations on the purchase of your state-of-the-art vehicle security system. It has been designed to provide years of trouble-free operation. This system must be installed by an authorized dealer. Installation of this product by anyone other than an authorized dealer voids the warranty. As verification of authorization, all authorized dealers are provided with preprinted dealer certificates.
fcc/id notice This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this device. Directed Electronics, Inc.
transmitter functions This system uses computer-based code learning to learn the transmitter buttons. This makes it possible to assign any transmitter button to any system function. The transmitter initially comes programmed with standard configuration, but may also be customized using the CliffNet Wizard PC program. The buttons in all of the instructions in this manual correspond to a standard configuration transmitter.
using your system The buttons used in the instructions in this manual correspond to the standard transmitter configuration. If your transmitter has been custom configured, the icons on your transmitter buttons may not correspond to the indicated functions. arming You can activate, or arm, the system by pressing on your trans- mitter for one second. When the system arms, you will hear two short siren sounds, or chirps, and see the parking lights flash twice. The LED will begin to flash steadily.
and programmed for passive locking) at 30 seconds, but the siren will not chirp. The early chirps provide you with a 25-second warning prior to arming. When armed, your vehicle is protected as follows: z The LED will flash as a visible theft deterrent. z Light impacts will trigger the Warning Zone signal. When triggered, the siren will chirp for a few seconds. z Heavy impacts will trigger the system.
disarming without a transmitter This feature allows you to disarm the system without the transmitter should it be lost, damaged, or disabled. In order to disarm without a transmitter, you must have the vehicle’s ignition key, know where the PlainView 2 Valet switch is located, and have the PIN code. Be sure to check with the installer for the location of the PlainView 2 Valet switch and instructions for entering the PIN code.
transmitter sensor disable To temporarily disable a sensor input, arm the system, press the and simultaneously. The lights will flash four times and all warn away trigger zones three and eight are bypassed. Press the buttons again; the lights flash four times and both warn away and full trigger zones three and eight are bypassed until the system is disarmed. This can be performed anytime the system is armed. 1. Arm the system. 2. Using the transmitter, bypass the sensor. 3.
auxiliary channel bypass Alarm sensor input zones three and eight will be bypassed while a pulsed or timed auxiliary Output is active. panic mode with smart door locking If you are threatened in or near your vehicle, you can attract attention by triggering the system with your transmitter! Just press for two seconds to enter Panic Mode. The siren will sound and the parking lights will flash for the programmed duration.
3. After the last digit continue to hold three seconds. for The LED status indicator will light steadily if you are entering Valet Mode and will turn off if you are exiting Valet Mode. To exit Valet Mode: 1. Turn the ignition on. 2. Within 10-seconds press once. note: The pin code can be entered after turning the ignition On and the press and hold the blank key on the PlainView 2 Valet switch for one second. transmitter valet mode The operations described in this section refer to transmitter buttons.
battery saver mode After 48 hours in the armed state, the LED will decrease the flash rate to /2 the normal rate; after 96 hours it will decrease to 1/4 the normal rate. 1 low battery warning When the transmitter battery is low, the system will generate five quick chirps when disarmed. note: The optional self-powered smart siren will generate a low-pitched tone. instant auto-arming bypass This will bypass the auto arm feature once only. 1. With the key, turn the ignition on, then off within two seconds.
multiple event total recall This will report the last eight system triggers. 1. Press and hold of the PlainView 2 Valet switch. 2. While still holding release the button. 3. The LED will start to blink to indicate the most recent trigger and proceed down to the eighth trigger. If fewer than eight triggers are stored in memory, the LED will blink continuously until the system is armed/disarmed using the transmitter after recalling the final trigger.
Doors are covered by FACT II differently; if the alarm is triggered by an open door for three full cycles, the doors will be bypassed until the trigger ceases. FACT II is programmable. See the Programming Options section of this guide. note: Arming and disarming the system does not reset this function! The only way to reset a bypassed zone is for 60 minutes or to turn on the ignition.
Press on the PlainView 2 Valet switch while playing the desired sound to add that sound; press while playing the desired sound to delete that sound. diagnostics The microprocessor at the heart of your security system is constantly monitoring all of the switches and sensors that are connected to it. It detects any faulty switches and sensors and prevents them from disabling the entire system. The microprocessor will also record and report any triggers that occurred during your absence.
disarming diagnostics Extra disarm chirps are the Tamper Alert. If three chirps are heard when disarming, the system was triggered in your absence. If three chirps are heard, the LED status indicator will indicate which zone was involved (see the Table of Zones section). The system will retain this information in its memory. Refer to the Multiple Event Total Recall section of this guide.
Zone - Number of LED Flashes Description 3 Instant trigger - a heavier impact detected by the shock sensor 4 Door switch trigger 5 Instant trigger - often used for hood/trunk pinswitches 7 Ignition trigger 8 Instant trigger - for optional sensors 10 System Power Reset Dealer-Installed Options anti-code grabbing (ACG) This unit features Anti-Code Grabbing (ACG) with Random Code Encryption.
high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode.
z Power Saver in Valet Mode: When the system enters Valet Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet Mode, the LED will shut off. If the system remains in Valet Mode, the LED will come back on the next time the ignition is turned on and then back off. programming options Programming options control what your system does during normal operation, and require few or no additional parts.
locking allows the vehicle's doors to lock when the security system passively arms (after the 30 second countdown). This feature only works if passive arming has been programmed. z Panic mode enabled/disabled: Some states have laws against siren capability. z Full trigger response 30, 60, or 90 seconds: This determines how long the full triggered sequence lasts. Some states have laws regulating how long a security system can sound before it is considered a nuisance.
2. Enter PIN - Enter the factory preset PIN code of 2 by pressing on the PlainView 2 Valet switch twice, then once. 3. Hold/Chirp/Release - After entering the PIN code, press and hold until a chirp is heard and the LED turns on, then release the button. You have now entered the feature selection position of the User Selectable Features grid. 4. Column select - Press the same number of times as the desired column.
user selectable features Then Press First Press Add new remote (autolearn) Auto arm on/off Set PIN code Chirps on/off/quiet* FACT II on/off New remote learn silent mode Auto lock ignition/off/rpm** Remote valet on/off New remote learn remote valet Auto unlock ignition/off Entry delay on/off New remote learn remote start** Passive lock on/off Reset to default (except transmitter and valet code) Panic on/off New remote learn window down/vent*** Clear all remotes Not used Not used Siren dura
auto arm - on/off z On: When the system sees the ignition turn off and the last protected entry (door, hood, or trunk) close, it will begin a 30-second countdown before arming itself. After the first five seconds, you will hear two chirps and the lights will flash. The system will arm 25 seconds later. z Off: The transmitter must be used to arm the system. chirps - on/off/quiet z On: Chirps will sound when arming/disarming the system. z Off: Chirps will not sound when arming/disarming the system.
passive lock - on/off z On: The doors will lock when the system passively arms. This feature only applies when passive arming is programmed on. z Off: The doors will not lock when the system passively arms. siren duration - 30/60/90 z The system will sound the alarm for the programmed duration (30/60/90 seconds) during an alarm trigger or when the system is put into panic mode.
select siren sounds z The individual sounds the 515C siren produces during an full trigger alarm can be customized for owner recognition of an alarm trigger. For more information, please refer to the Select Siren Sounds section of this guide. fact II on/off z On: The alarm will bypass for 60 minutes if zones 3, 5, and 8 are triggered three times within a one hour period. z Off: The alarm will respond to zones 3, 5, and 8 inputs indefinitely without bypassing.
panic on/off z On: The panic feature is available. z Off: The panic feature is not available. user selectable features descriptions - column three The features in this column pertain to programming individual transmitter channels in custom configurations. Following is an explanation of the features. To program specific functions to a different button, enter the function you are programming after the chirp confirmation.
remote valet z The transmitter channel programmed into this feature will make the system enter/exit valet mode. remote start z This feature is only available with IntelliStart connected z The transmitter channel programmed into this feature will activate or shut down the Intellistart remote start system.
pin programming A PIN code can have one to four digits; each digit can be from 0-9. note: A PIN code cannot begin with a zero. Programming Procedure 1. Enter the feature location in the installer programming grid. 2. Immediately press and release switch. 3. Select each digit by pressing of the PlainView 2 Valet 1-9 times, and then press to enter the number into the system. To enter a zero, press only. To program a PIN code of 1032: 28 1. Press and release hear one chirp. once and once.
PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set. 1. Turn on the ignition. 2. Enter the new PIN code. 3. Press and hold for three seconds. z LED turns on: New PIN code is learned and programming is complete. z LED stays off: New PIN code is not learned and the system reverts to the old PIN code. Redo the programming sequence. glossary of terms Control Unit: The "brain" of your system.
LED: Blue light mounted somewhere in the vehicle. It is used to indi- cate the status of your system. It is also used to report triggers and faults in the system or sensors. Shock Sensor: This is a sensor mounted in the vehicle that is designed to pick up impacts to the vehicle. Siren: Noise generating device usually installed in the engine compart- ment of the vehicle. It is responsible for generating the "chirps" you hear, as well as the six tones you hear while the alarm is triggered.
security & convenience expansions Here we have listed only some of the many expansion options available. Please contact your dealer for a complete list of all the options available to you. Backup Battery: The 520T keeps the system armed, triggers the alarm and keeps the starter interrupt active if main battery power is disconnected. Field Disturbance Sensor: An invisible dome of coverage is established by installing the 508D "radar" sensor.
32
health check Directed Electronics recommends you return to your installing Clifford dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. © 2 0 0 4 d i re c t e d e l e c t ro n i c s , i n c .
The company behind this system is Directed Electronics, Inc. Since its inception, Directed® has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology, Directed® is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.
