Responder One Remote Start Owner's Guide © 2008 Directed Electronics, Vista, CA G4203X 2008-09
Contents Government Regulations.....................................................................................5 Warning! Safety first..........................................................................................7 What is Included ............................................................................................9 Important Information.........................................................................................9 System Maintenance........................................
Government Regulations This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules.
Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control transmitter. Therefore, never operate the system in an enclosed area or partially enclosed area without ventilation (such as a garage).
After the remote start module has been installed, contact your authorized dealer to have him or her test the remote start module by performing the Safety Check outlined in the product installation guide. If the vehicle starts when performing the Neutral Safety Shutdown Circuit test, the remote start unit has not been properly installed. The remote start module must be removed or the installer must properly reinstall the remote start system so that the vehicle does not start in gear.
What is Included • • • • • The control module Two 1-button transmitters (P/N 7211X) A push-button programming switch Your warranty card A shut-down toggle switch Important Information Congratulations on the purchase of your remote start keyless entry system. This system has been designed to provide years of trouble-free operation. By carefully reading this owner’s guide prior to using your system, you can maximize the use of this system and its features.
Front Elastomer contact Front Front Circuit Board ➢ Battery Replacement Elastomer Elastomer contact Front Front Note: Make sure that the small elas- Circuit Board Front Elastomer contact Elastomer contact 1. Using acontact small slotted screwdriver, insert into slot located on the side of the unit as shown and carefully pry the front of the unit up, working your way around the edge until the front is completely separated from the housing.
Using Your System ➢ Unlocking Only after the vehicle is remotely started via the transmitter, press and release the transmitter button for 1 second to unlock the vehicle’s doors. The remote responds with 2 short beeps and the green LED on the remote flashes once. The vehicle responds by flashing the parking lights twice and honking the horn twice to confirm unlocking. Note: horn honk is an optional feature.
Note: In order for the ignition controlled door locks to work, the feature must be turned on in programming. Note: If the ignition is turned on while the vehicle is remote started the doors do not lock until the remote start shuts off. To avoid being locked out of the vehicle, do not turn the ignition on until you are ready to drive the vehicle. ➢ Remote Start This feature allows you to remotely start and run your vehicle for a programmable period of time.
To shut off the remote start: While the vehicle is remote started press and hold the button on the remote for 3 seconds. The remote plays the remote start shut off tones and the orange LED flashes 1 time. The vehicle shuts down from the remote start mode. Once the remote start is on, when you are ready to drive the vehicle: 1. 2. Insert the ignition key and turn it to the ON (not the START) position. Press the brake pedal. The vehicle stays running and is ready to drive.
➢ Valet Take-Over The Valet Take-Over feature allows the vehicle to remain running after the key has been removed from the ignition. This feature is useful for occasions when you wish to exit and lock the vehicle for short periods of time, but would like to leave the motor running and the climate controls on. To perform Valet Take-Over: 1. 2. 3. Before turning off the engine, press and release the single button once.
Programming options Programming options control your system's normal operational set-up. Most options do not require additional parts, but some may require installation labor. The following is a list of the programmable options, with the factory settings in bold. • 12, 24, or 60 minute run time. Your system can be programmed to allow the vehicle to run for 12, 24, or 60 minutes when remote started. Can be set up to minute increments by your installer. • Parking lights flashing or constant.
To remote start the vehicle • Press and release the transmitter button for 1-second. The remote responds with the remote start ON tones and the green LED on the remote flashes once. The parking lights turn on constant to confirm remote start operation. To shut down remote start • Press and hold the transmitter button for 3 seconds. The remote will play the remote start shut off tones and the orange LED will flash 1 time The parking lights will turn off.
Limited lifetime consumer warranty Directed Electronics.
WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND. IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY, THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA. CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN THE DISPUTE.
The company behind this system is Directed Electronics Since its inception, Directed Electronics has had one purpose, to provide consumers with the finest vehicle security and car stereo products and accessories available. The recipient of nearly 100 patents and Innovations Awards in the field of advanced electronic technology. Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.
