Intelliguard 950 Owner’s Guide
limited lifetime consumer warranty Directed Electronics, Inc.
THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights and you may also have other rights that vary from State to State or Country to Country.
contents limited lifetime consumer . . . . . . . diagnostics . . . . . . . . . . . . . . . . . .16 warranty . . . . . . . . . . . . . . . . . . . . .i arming diagnostics . . . . . . . . .16 what is included . . . . . . . . . . . . .3 important information . . . . . . . . .3 system maintenance . . . . . . . .4 your warranty . . . . . . . . . . . . .4 transmitter configurations . . . . . .5 transmitter functions . . . . . . . . . .6 standard configuration for 5-but- disarming diagnostics . . . . . . .
blackjax* off warning indicator . glossary of terms . . . . . . . . . . . . .36 . . . . . . . . . . . . . . . . . . . . . . .35 security & convenience expansions system sensors and adjustments . . . . . . . . . . . . . . . . . . . . . . .35 2 . . . . . . . . . . . . . . . . . . . . . . . . . . .38 health check . . . . . . . . . . . . . . . .
what is included z Intelliguard 950 Security System z One 5-button transmitter and one 4-button transmitter z Presentation envelope and quick reference card z Two window decals z XHF antenna/receiver z Blue status LED z PlainView 2 Valet switch z 515C Smart Self-powered siren z Tilt/Motion sensor z One of the following sensor options Digital Dual-Zone proximity sensor Ultrasonic sensor Glass Tamper sensor important information Congratulations on the purchase of your state-of-t
note: Your system MUST be installed by an Authorised dealer in accordance with the instructions we supply them. The Clifford Intelliguard 950 system is designed to be installed in any petrol or common rail diesel vehicle with a 12-volt battery. note: The Installation Certificate must be completed by your installer at the authorised dealer. Other than the remote controls, this system has no user-serviceable parts.
transmitter configurations Your Intelliguard 950 system has a 5-button and 4-button remote control. Your system can accept up to 2 additional remotes. Each remote can be used to control the various standard features and options of your system as shown in the following pages.
transmitter functions This system uses computer-based code learning to learn the transmitter buttons. This makes it possible to assign any transmitter button to any system function. The transmitter initially comes programmed with standard configuration, but may also be customised using the CliffNet Wizard PC program. The buttons in all of the instructions in this manual correspond to a standard configuration transmitter.
Button, then Button These buttons activate the optional SmartWindows. Button, then Button Accessory C output is controlled by these buttons. Button twice, then Button These buttons activate remote valet. Button twice, then Button These buttons disable the sensors. Button twice, then Button These buttons enter safe start mode for manual transmission vehicles and activate Autostart mode. (Requires optional Intellistart* accessory.
Button Remote start is controlled by this button. (Requires optional Intellistart* accessory.) and Buttons Silent arm/disarm is controlled by these buttons. and Buttons These buttons activate the optional SmartWindows. and Buttons These buttons activate remote valet. and Buttons These buttons activate Accessory output C. and Buttons These buttons disable the sensors. and Buttons These buttons enter safe start mode for manual transmission vehicles and activate Autostart mode.
using your system The buttons used in the instructions in this manual correspond to the standard transmitter configuration. If your transmitter has been custom configured, the icons on your transmitter buttons may not correspond to the indicated functions. arming You can activate, or arm, the system by pressing on your trans- mitter for one second. When the system arms, you will hear two short siren sounds, or chirps, and see the indicator lights flash twice. The LED will begin to flash steadily.
not chirp. The early chirps provide you with a 25-second warning prior to arming. note: If any protected entry point (a door or a switch-protected boot or bonnet) is open, the system will not passively arm. Additionally, each time a protected entry is triggered during the arming countdown, the 30-second countdown starts from the beginning. When armed, your vehicle is protected as follows: z The LED will flash as a visible theft deterrent.
disarming without a transmitter This feature allows you to disarm the system without the transmitter should it be lost, damaged, or disabled. In order to disarm without a transmitter, you must have the vehicle’s ignition key, know where the PlainView 2 Valet switch is located, and have the PIN code. Be sure to check with the installer for the location of the PlainView 2 Valet switch. Please refer to the Disarm/Valet Mode section of this guide for instructions to enter the pin code.
transmitter sensor disable To temporarily disable a sensor input, arm the system, press twice and then . The lights will flash four times and all warn away trigger zones one, two, three, and eight are bypassed. Press the buttons again; the lights flash four times and both warn away and full trigger zones one, two, three, and eight are bypassed until the system is disarmed. This can be performed anytime the system is armed. 1. Arm the system. 2. Press 3.
auxiliary channel bypass Alarm sensor input zones one, two, three, and eight will be bypassed while a pulsed or timed auxiliary Output is active. disarm/valet mode Entering your pin code using the PlainView 2 Valet switch allows you to disarm the system or enter valet mode without using the transmitter. In valet mode, the security system will not arm, even with the transmitter, but all convenience functions (door locks, boot release, etc.) will continue to work normally. To disarm or enter Valet Mode: 1.
3. After the last digit of the pin code is entered: a. To disarm the system: press and release b. To enter valet mode: Press and hold . for three seconds. The LED status indicator will illuminate continuously if you are entering Valet Mode and will turn off if you are exiting Valet Mode. To exit Valet Mode: 1. Turn the ignition on. The system will then automatically exit Valet mode. transmitter valet mode The operations described in this section refer to transmitter buttons.
one-time auto-arming bypass This will bypass the auto arm feature once only. 1. With the key, turn the ignition on, then off within two seconds. 2. The siren will chirp once to confirm auto arming bypass. 3. The system will not auto arm. note: The system will revert to normal auto arming when the system sees the ignition on for at least three seconds.
multiple event total recall This will report the last eight system triggers. 1. Press and hold of the PlainView 2 Valet switch. 2. While still holding release the button. 3. The LED will start to blink to indicate the most recent trigger and proceed down to the eighth trigger. If fewer than eight triggers are stored in memory, the LED will flash continuously until the system is armed/disarmed using the transmitter or the ignition is turned on.
The security system will ignore the input that was active when the system was armed, until the input goes away. Three seconds later the system will monitor that input normally. For example, if your vehicle has the boot open, and you arm the system, you will hear Bypass Notification chirps. Once you shut the boot, however, it is then monitored normally. disarming diagnostics Extra disarm chirps are the Tamper Alert warning. If you hear three chirps when disarming, the system was triggered in your absence.
table of zones The zone number is the number of LED flashes used by the system to identify a specific input. The standard input assignments are listed below, along with spaces to write in any optional sensors or switches you have had installed. If the Warning Zone response is triggered, the LED will not report it.
high frequency Your system transmits and receives at 433 MHz. This provides a cleaner spectrum with less interference and a more stable signal. smart power up II This security system will store its current state to non-volatile memory. If power is lost and then reconnected the system will recall the stored state from memory. This means if the unit is in Valet Mode and the battery is disconnected for any reason, such as servicing the car, when the battery is reconnected the unit will still be in Valet Mode.
z Power Saver in Valet Mode: When the system enters Valet Mode the LED illuminates steadily. If the vehicle is not used (ignition is not turned on) for a period of one hour while the system is in Valet Mode, the LED will shut off. If the system remains in Valet Mode, the LED will come back on the next time the ignition is turned on and then back off. programming options Programming options control what your system does during normal operation, and require few or no additional parts.
system passively arms (after the 30 second countdown). This feature only works if passive arming has been programmed. z Reset the system to all factory defaults z Entry delay feature on/off z Add or remove remote controls. z BlackJax* feature on or off. z Change PIN code. z Custom configure the remote control. z Remote valet on or off. z Autostart** with low battery voltage or cold temperature.
manual programming instructions It is a good idea to document changes by taking note of all feature changes made in programming mode. To enter the User Selectable Features programming: 1. Ignition on - Turn the ignition to the run position or start the engine. 2. Enter PIN - Enter the factory preset PIN code. note: If the factory preset PIN has been changed, the new PIN must be entered. 3.
note: Refer to the Feature Descriptions sections of this guide for important notes and descriptions of the system features and programming. 7. Exit programming - To exit programming mode turn the ignition off or wait 60 seconds without pressing the PlainView 2 Valet switch. The siren will chirp three times to indicate programming mode has been exited.
user selectable features descriptions - column one add new remote (auto learn) Auto-learn new five-button Radar2 remote controls to the system in the standard button configuration. Once you have entered the feature, press on the transmitter until you hear a confirmation chirp. Press again until you hear two chirps indicating the new remote is learned.
auto unlock - ignition/off z Ignition: The doors will automatically unlock as soon as the ignition is turned off. z Off: The doors will not automatically unlock when the ignition is turned off auto (passive) arm and lock - on/off z On: The doors will lock when the system passively arms. This feature only applies when passive arming is programmed on. z Off: The doors will not lock when the system passively arms.
entry delay on/off z On: If the system has passively armed, it will not trigger for 15 seconds after a door is opened allowing the user to enter the vehicle and disarm the system via the PlainView 2 Valet switch. z Off: There is no entry delay when armed. The system will trigger instantly when a door is opened.
blackjax* on/off z On: The system will enter BlackJax mode when triggered. z Off: The system cannot enter BlackJax mode. user selectable features descriptions - column three The features in this column pertain to programming individual transmitter channels in custom configurations. Following is an explanation of the features. The 4-button remote must be programmed using this column as it cannot be autolearned.
accessory b output The transmitter channel programmed into this feature will activate the accessory output. silent mode The transmitter channel programmed into this feature will arm/disarm the system, but the siren will not chirp. remote valet The transmitter channel programmed into this feature will make the system enter/exit valet mode.
ters that have been lost, stolen, or incorrectly programmed into the system. z After entering this feature press any button on the transmitter; the siren will chirp to indicate that all transmitters have been erased from memory. pin programming A PIN code can have one to four digits; each digit can be from 0-9. note: A PIN code cannot begin with a zero. Programming Procedure 1. Enter the feature location in the installer programming grid. 2. Immediately press and release switch. 3.
d. Press and release two times, and then press once. You will hear two chirps. 4. Wait for two siren chirps after a five second pause or five seconds after the last digit has been entered if using less than four digit code number. 5. Turn off the ignition; the siren will chirp three times. 6. The programming mode is now exited. PIN Code Confirmation Procedure Begin this procedure within 15 seconds of finishing the programming sequence or the new code will not be set. 1. Turn on the ignition. 2.
auto-immobilisation sequence 1. Turn ignition off or disarm alarm 2. After 30 seconds the systems Immobilisation circuits activate and engage the starter and ignition interrupt 3. LED flashes at ½ normal speed Disarming auto-immobilisation To disarm auto-immobilisation when active, follow any of the sequences listed below. z Turn ignition on and press the arm/disarm button. z Arm the alarm and then disarm the alarm. z Turn the ignition on and enter the system valet/PIN code.
blackjax* feature Clifford's exclusive BlackJax feature provides a safe and effective means of recovering your vehicle after a carjacking by monitoring the door input, brakes, and engine speed. Simply get out of the vehicle and let the thief drive away. After the vehicle is at a safe distance BlackJax will activate the siren and brake lights to draw attention to the vehicle.
3. 4. 5. Press and release brake pedal. a. System sees the brake pedal pressed. b. System then begins monitoring the engine speed. c. System sees the engine speed at two times idle. BlackJax* begins 20 second countdown. After a 20 second countdown: a. 5 siren chirps as reminder to enter PIN code. b. Brake light output pulses to flash brake lights. c. You then have 20 more seconds to enter PIN to turn off Blackjax.
blackjax* deactivation sequence To deactivate BlackJax turn the key on and then enter the PIN code at any time. bypass blackjax temporarily This feature allows you to easily bypass BlackJax activation when another person drives your vehicle that should not know your PIN code. (IE: valet parking, mechanic) Bypass BlackJax temporarily 1. Turn ignition on. 2. Enter PIN code. Do not enter valet or programming mode. 3. Within 10 seconds press 4. Siren chirps 1 time as confirmation of BlackJax bypassed.
5. Turn ignition off, siren chirps 3 times as confirmation of exiting programming. note: If ignition remains on after entering PIN code and no action for 10 seconds, unit will automatically exit programming mode without chirps. blackjax* off warning indicator Each time the ignition is turned off when BlackJax is bypassed the LED will flash 10 times as warning that the BlackJax has been temporarily bypassed.
Ultrasonic Sensor: The 509U sensor is used to provide coverage of a vehicle’s interior cabin area. The sensor detects movement inside the vehicle by sensing air disturbance. Glass Tamper Sensor: Metal on glass, glass cracking, and breaking glass each produce distinctive acoustic signatures. The 506T glass tamper sensor uses a microphone to pick up sounds, and then analyzes them with proprietary acoustic software to determine if the glass has been struck.
PlainView 2 Valet Switch: A small two-button switch mounted some- where inside the vehicle. It is used to override the alarm when a transmitter is lost or damaged, or to enter or exit Valet mode. Smart Self-Powered Siren: Noise generating device usually installed in the engine compartment of the vehicle. It is responsible for generating the "chirps" you hear, as well as the sound you hear while the alarm is triggered.
security & convenience expansions Here we have listed only some of the many expansion options available. Please contact your dealer for a complete list of all the options available to you. Remote Boot Release: The button can operate a factory electric release for the vehicle’s boot or hatch. (An optional relay may be required.) If the factory release is not electrically activated, the Directed®'s 522T boot release solenoid can often be added.
health check Directed Electronics recommends you return to your installing Clifford dealer to have your system checked for correct operation. The first check is due one year after the installation date and at yearly intervals thereafter. note: There may be a small charge incurred for this service. © 2 0 0 4 d i re c t e d e l e c t ro n i c s , i n c .
Your factory set 4-digit PIN code is noted below. See page 13 for information on using your PIN code. place sticker here The company behind this system is Directed Electronics, Inc. E&OE, specification is subject to change without notice. Some vehicles require optional parts/wiring and a few are incompatible with some features. Directed® is committed to delivering world-class quality products and services that excite and delight our customers.
