OWNER ’S GUIDE INSTALLATION GUIDE LCD Video Monitor MODEL RVM560, RVM680, RVM700
Table of Contents Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 When Cleaning the Vehicle...........................................................................................................5 While Driving ...............................
Limited Three-Year Warranty For a period of THREE YEARS from the date of purchase, troubleshooting or reinstallation of the unit. For service on Directed Electronics, Inc. ("DIRECTED") promises to the an out-of-warranty product a flat fate fee by model is original purchaser to repair or replace, free of cost, with a charged. Contact your authorized dealer to obtain the serv- comparable reconditioned model any VIDEO MONITOR ice charge for your unit.
Safety Instructions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE INCLUDED HARDWARE. THIS MONITOR IS ONLY DESIGNED FOR REAR SEAT PASSENGER VIEWING AND IS NOT INTENDED FOR VIEWING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION. SUCH USE MAY DISTRACT THE DRIVER OR INTERFERE WITH THE SAFE OPERATION OF THE VEHICLE, AND MAY ALSO VIOLATE STATE LAW.
PROPER USE REPAIRS Do not touch the screen unless cleaning with a If the monitor stops working for any reason, dis- soft dry cloth. Do not pull or hang from the fold continue use immediately and consult with your down monitor door. retailer about any necessary repairs Important Information FCC NOTICE YOUR WARRANTY This device complies with Part 15 of FCC rules.
Basic Operation 2 1 4 5 6 4 3 MONITOR DESCRIPTION MAINTENANCE 1. Screen - TFT active matrix LCD screen. Keep the monitor clean and free of dust and 2. Power/Source button - Press to turn the monitor on/off or change video source. moisture and it will provide years of trouble free ■ Press to turn the monitor on. ■ Press for more than three seconds to turn the monitor off. ■ Press for less than three seconds when on to change the source. IR remote input - For remote control operation.
On-Screen Menus The Setup Menu is a list of programming selec- Basic Operation section of this guide. tions that control system operation and screen settings. Each selection has a list of settings that can be changed to optimize system operation. Some settings may have additional settings. 1. Press MODE to enter the Setup Menu. 2. Press UP or DOWN to highlight the selection. 3. Press MODE to enter that selection Menu. 4. Press UP or DOWN to highlight the setting. 5.
SETUP MENU DESCRIPTIONS AND OPERATION Following are explanations of the many settings that can be changed to customize the operation of your Rear Seat Entertainment system. To change the settings described, follow the directions in the on-screen menus section or the special instructions in each menu. SELECTION DESCRIPTION AND OPERATION CHANNEL (TVM300 ONLY) ■ ■ DIMMER ■ ■ ■ ■ PICTURE ■ Note: To adjust use the monitor’s UP/DOWN buttons or the remotes (+)/(-) buttons.
SECURITY (ESP/ESP2 ONLY) ■ NOTE: This menu contains selections that have additional settings. ■ ■ SETUP (MCB1000 ONLY) NOTE: This menu contains selections that have additional settings. This menu is used for initial system setup only. ■ ■ ■ ■ IMPORTANT! ESP/ESP2 programming and zone information. TRIGGER INFORMATION - Displays ESP/ESP2 zone information. (Always displays the last zone triggered only.) See the Assign Trigger Names menu. SYSTEM SETTINGS - Displays the System Settings menu.
WRITE TO SYSTEM ■ ■ ■ ■ Highlight WRITE TO SYSTEM, press the monitor’s MODE button or the remotes MENU button to enter the system changes. WRITING TO SYSTEM will be displayed. WRITE SUCCESSFUL - Information entered successfully. WRITE FAILED - Information not entered successfully. HARDWARE OPTIONS MENU SELECTION DESCRIPTION AND OPERATION POWER AUTO OFF ■ ■ ■ FM MODULATOR ■ ■ ■ ■ ANTENNA TV ■ ■ ■ Select to choose POWER AUTO OFF or POWER LAST STATE.
ASSIGN SOURCE NAMES MENU NOTE: In this menu use the monitor’s MODE button or the remote’s MENU button to toggle through the available choices for source names. SELECTION DESCRIPTION AND OPERATION SOURCE 1: AV1 Select to change the name of source 1 from the source names list at the end of this section. SOURCE 2: AV2 Select to change the name of source 2 from the source names list at the end of this section.
ZONE 8 Select to change the name of zone 8 from the zone names list at the end of this section. WRITE TO SYSTEM ■ ■ ■ ■ Highlight WRITE TO SYSTEM, press the monitor’s MODE button or the remotes MENU button to enter the system changes. WRITING TO SYSTEM will be displayed. WRITE SUCCESSFUL - Information entered successfully. WRITE FAILED - Information not entered successfully.
Installation MONITOR SPECIFICATIONS RVM 560 Screen size 5.6" Resolution 74,880 pixels View angle Top 10 degrees Bottom 30 degrees Left 45 degrees Right 45 degrees Video system ntsc/pal Osd language English Power requirements 10 - 15 vdc Operating temp. 35 - 115 degrees fahrenheit 6.8" Resolution 89,856 pixels View angle Top 10 degrees Bottom 30 degrees Left 45 degrees Right 45 degrees Video system ntsc/pal Osd language English Power requirements 10 - 15 vdc Operating temp.
Monitor Connector Monitor Mounts © 2001 Directed Electronics, Inc.
The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide consumers with the finest vehicle security, car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology, Directed is ISO 9001 registered. Quality Directed Electronics products are sold and serviced throughout North America and around the world.
