Installation guide

ManualsBrandsDirected ManualsAutomotive1-button series

InstallatIon GuIde

1100 Series Key Fob Transmitters

Description

The DMP 1100 Series Wireless Key Fob transmitters are available in a Four-Button (1145-4), Two-Button (1145-2),

One-Button (1145-1), or One-Button with Prox Patch™ (1145-1-BP) arrangement and are designed to be clipped to a

key ring or lanyard. Key Fob features include a durable water resistant housing, ergonomic button design for ease of

use, and a status feedback LED for visual conrmation. The button status LED responds with specic color-coded LED

displays to indicate system status.

The One-Button with Prox Patch (1145-1-BP) Key Fob includes a built-in 1306P proximity credential for access

control. This accessory allows controlling the system for such functions as arming, disarming or access control via

the access control credential.

Each button can be individually programmed for one of nine different actions. Key fob programming defaults to the

typical use of the key fob such as Arming, Disarming, and Panic operations. Figure 1 shows the three key fob button

congurations and the table below identies the default programming for each button. Unique labels are available

to identify the use of each button. See Figure 2.

Connect

Key Ring or

Lanyard Here

LED

Front View

Side View All Key Fob

Left

Button

Top Button

Right

Button

Bottom

Button

Front

Back

Slot Location

1145-2

2-Button Layout

1145-1

1-Button Layout

Top

Button

Bottom

Button

1145-4

4-Button Layout

One

(Top)

Button

Figure 1: 1100 Series Key Fob Transmitters

Compatibility

• 1100 Series Wireless Receivers and Repeater. See Compatibility Chart on back page.

What is Included

The 1100 Series Key Fob includes the following items:

• One key fob transmitter (1145-1-BP, 1145-1, 1145-2, or 1145-4)

• One 1306P Prox Patch™ credential (1145-1-BP only)

• One 3.0V lithium coin cell battery

• Peel-off button ID labels

• Serial number label

Key Fob Model

Button

Position

Default

Programming

1145-4 (Four-Button)

To p Arm

Bottom Disarm

Left Panic

Right

Arm Area 1 or

Perimeter

1145-2 (Two-Button)

To p Arm

Bottom Disarm

1145-1 (One-Button) Top Panic

1145-1-BP (One-Button) Top Panic

Summary of content (4 pages)

PAGE 1
Installation Guide 1100 Series Key Fob Transmitters Description The DMP 1100 Series Wireless Key Fob transmitters are available in a Four-Button (1145-4), Two-Button (1145-2), One‑Button (1145-1), or One‑Button with Prox Patch™ (1145-1-BP) arrangement and are designed to be clipped to a key ring or lanyard. Key Fob features include a durable water resistant housing, ergonomic button design for ease of use, and a status feedback LED for visual confirmation.
PAGE 2
Transmitter Serial Number For your convenience, an additional pre-printed serial number label is included. Prior to programming the device, record the serial number or place the pre-printed serial number label on the 1100 Series Key Fob Programming Sheet (LT‑0706) included with the wireless receiver. This number is required during programming. Programming the Key Fob in the Panel Refer to the panel programming guide and 1100 Series Key Fob Programming Sheet (LT-0706) as needed.
PAGE 3
Replacing the Battery The 1145 Series Key Fob reports a low battery condition by automatically testing for a low battery on a daily basis. When replacement of the key fob battery is necessary, a LOBAT message will display on the keypad and require a Sensor Reset. Observe polarity when installing the battery. Use only 3.0V coin cell batteries, DMP Model CR2032, or the equivalent CR2032 battery from a local retail outlet. 1.
PAGE 4
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.