Manual

TOOLREQUIRED:FLATHEABANDPHILLIPSSCREWDRIVER
WARNING:TO REDUCETHERISKOFELECTRICSHOCK- UNPLUGCLEANERBEFOREREMOVINGOR
REPLACINGLIGHTBULB.
This cleanerusesa commonautomotive lamp #906, 13.0 volts, Forbulb replacement call 1-800-321-1134
or your local auto parts store,
Lean cleaner handle
back. Removethe one
(1)screw.
Using the end of
Flathead screwdriver,
gently pop open the
lens. Removelens.
Pull bulb of of socket.
Do NOT twist. Gently
pushbulb intosocketto
replace.
Snap lens back into
place.Securethe head-
light lens by replacing
the onescrew.
WARNING:TO REDUCETHERISKOFINJURYFROMMOVINGPARTS- UNPLUGBEFORESERVICING.
DEBRIS DEBRISREMOVAL/
REMOVAL/HOSE NOZZLEGUARD
DEBRISREMOVAL!POWERBRUSHTOOL
1. Check to see if dirt container is full; empty
if needed.
2. Plug cleaner in and check to see if there is
any suctionat end of hose.Ifthere is suction
at end of hose,moveon to Diagram4. If there
isno suction atthe end of hose, follow these
steps: 1. Unwrap hose from caddy. Remove
obstruction. Check access door on back of
cleaner (near hosewand). Removethree (3)
screws and checkfor obstruction(Diagram1).
2. Removedirt container(Pg.B)andcheckdirt
container inlet locatedon cleaner (Diagram2).
3. Remove nozzle guard (see Diagram 3) by
removing the three (3) screws. Remove
obstruction.
LOCKINGRiNG
Rotatelocking ring 180° and
turn PowerBrushTool over.
Pivot lower housing and
removeclog.
To reassemble, be sure tabs
are engaged. Pivot the lower
housingclosed.
WARNING:TO REDUCERISKOFPERSONALINJURY- UNPLUGCLEANERBEFORESERVICING
PROBLEM POSSIBLE REASON
Cleaner WOn't run
2. Blown fuse or tripped breaker.
POSSIBLE SOLUTION
2. Check fuse or breaker in home. Replace
fuse/reset breaker.
Cleaner won't
pick-up or low
suction
4. Thermal Protector activated. 4. Allow cleaner to cool - Pg. 3.
2.
4.
Dirtcontainerfull.
Brokenorwornbelt.
2. Empty dirt container- Pg. 8.
4, Replace belt - Pg, 10.
Dust escaping
from cleaner
Cleanertools won't
pick-up
Headlightnot
working
Cleaner is difficult
to push or won't
move forward
1. Dirt container full.
3. Hose not installed correctly.
1. Hose clogged.
1. Empty dirt container- Pg. 8.
3. Review hose installation - Pg. 6.
1. Remove hoseand tools; remove obstruction -
Pg, 6&11.
3. Oneor bothfiltersareclogged. 3. Removebothfilters andclean- Pg.8 & 9.
2. Loose electrical wires.
2. Taketo servicecenter.Tofind nearestlocation,
visitourwebsiteat www.dirtdevil.comorcall
1-800-321-1134.
ANY OTHER SERViCiNG SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE
CUSTOMERSERVICE (1-800-321=1134)
In the eventthat further assistance is required, see your Yellow Pagesfor an authorized Royal®Dealer or visit
ourwebsite at www.dirtdevil.com. Costsof anytransportationto and from any placeof repair areto be paidby the
owner. Theservicepartsusedinthis unitareeasilyreplacedandreadilyavailablefroman authorizedRoyal®Dealeror
retailer. Alwaysidentifyyour cleanerby the modelnumberand manufacturingcodewhen requestinginformationor
orderingreplacementparts. (Themodelnumberappearson the bottomof the cleaner.)
11 12