inside_front_cover.fm Page 1 Friday, February 11, 2005 4:17 PM WARNING AND ATTENTION SYMBOLS You must be aware of safety when you install and use this system. This User Guide provides various procedures. If you do some of these procedures carelessly, you could injure or kill yourself or damage equipment or property. Some other procedures require special attention. The WARNING! symbol means that if you are not careful: You could injure or kill yourself, or You could damage equipment or property.
Pyramid.book Page 1 Wednesday, February 16, 2005 4:00 PM TABLE OF CONTENTS Safety Instructions .............................................. 2 Introduction ......................................................... 3 Setting Up the Kit ................................................ 5 Setting Up the Signal Converter.......................... 5 Setting Up the Remote Control ........................... 9 Remote Control Operation ...............................
Pyramid.book Page 2 Wednesday, February 16, 2005 4:00 PM SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with a dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Pyramid.book Page 3 Wednesday, February 16, 2005 4:00 PM INTRODUCTION The IR-to-UHF Pro Upgrade Kit lets you use an ultra-high frequency (UHF) remote to control an infrared (IR) DISH Network satellite TV receiver from much farther away than with an IR remote control, even through walls that block IR signals. Note: The remote control/converter combination included in this kit works only with compatible DIS H Network receivers, and is not for any other devices.
Pyramid.book Page 4 Wednesday, February 16, 2005 4:00 PM The converter gets the UHF signal, changes it to IR, and sends the IR signal to the receiver. The best way to get the IR signal to the receiver is with the IR extender cable because the signal doesn’t have to go through the air, but you can also use just the converter to send the signal to the receiver (see the example in Figure 3). Figure 3.
Pyramid.book Page 5 Wednesday, February 16, 2005 4:00 PM SETTING UP THE KIT The kit includes a UHF Pro remote control, batteries, an IR extender cable, an IR clip, an AC adapter, a converter, and a UHF antenna. Figure 4. Parts of the IR-to-UHF Pro Upgrade Kit SETTING UP THE SIGNAL CONVERTER 1. Make sure you fully install the satellite TV system. See the satellite receiver’s User Guide. 2.
Pyramid.book Page 6 Wednesday, February 16, 2005 4:00 PM Tighten the connection only by hand. If you use a wrench, you may over-tighten the connection and damage your equipment. Such damage is not covered by the Limited Warranty. b. Make sure the REMOTE KEY switch matches the UHF Pro key at the bottom of the remote. If the switch setting does not match the key or if you'd like to change these settings, see Changing Frequencies on page 31. c.
Pyramid.book Page 7 Wednesday, February 16, 2005 4:00 PM Figure 7. IR Sensor behind a lens 5. To secure the IR head, peel the paper off the strip of tape on the head (the IR signal goes through the tape), and stick the head into place. 6. For DISH Player-DVR 522 and DISH Player-DVR 625, place the IR head about ¼” from the left side of the front panel lens. Figure 8. DISH Player-DVR 522 IR sensor 7. For DISH 301, DISH 311, DISH 322 receivers, you can use the IR head clip to set up the IR extender cable.
Pyramid.book Page 8 Wednesday, February 16, 2005 4:00 PM a. Attach the IR head clip to the receiver’s bottom panel, on the grate directly behind the front panel’s IR sensor. You must center the clip on the second slot from the left. There is a CLIP label on the bottom panel of some DISH 301, DISH 311, and DISH 322 receivers. b. Fit the IR head into the IR head clip, and route the IR extender cable out through the clip’s slot. 8. Route the IR extender cable under the back of the receiver, to the converter.
Pyramid.book Page 9 Wednesday, February 16, 2005 4:00 PM SETTING UP THE REMOTE CONTROL INSTALLING BATTERIES The remote control requires AAA batteries. When you replace old batteries, you should replace all of the batteries. Use batteries of the same kind, for example, alkaline or carbon zinc, and don’t mix batteries of different kinds. Alkaline batteries last longer. 1. Press down on the battery cover and slide the cover off. 2. If you are replacing batteries, take out all of the old batteries. 3.
Pyramid.book Page 10 Wednesday, February 16, 2005 4:00 PM 4. On the UHF Pro remote control that came with the kit, press and hold the SAT mode button for three seconds until all mode buttons light. Then, let go. 5. Use the NUMBER PAD buttons to enter the number you wrote in step 3. 6. Press the POUND (#) button. If you entered the address correctly, the SAT mode button will flash three times.
Pyramid.book Page 11 Wednesday, February 16, 2005 4:00 PM 5. Press the RECORD button. 6. Make sure the System Information screen shows the address number you entered in step 3. 7. Close the System Information screen. On most receivers, this is done by selecting Done. See your receiver user's guide for more information. CHECKING THE REMOTE CONTROL ADDRESS To check the remote control address setting: 1. Press and hold the SAT mode button for three seconds until all mode buttons light. Then, let go. 2.
Pyramid.book Page 12 Wednesday, February 16, 2005 4:00 PM Also, when you use the remote to control your VCR in Limited Mode, you will only be able to use the POWER and VCR function buttons. The section Setting Up Using Device Codes Tables has a step that tells the remote control to go into Limited Mode. Note: Limited Mode can not be used with audio amplifiers. SETTING UP USING DEVICE CODE TABLES You can set up the remote to control other devices using the device codes listed on page 33. 1.
Pyramid.book Page 13 Wednesday, February 16, 2005 4:00 PM 9. Turn the device back on and try some other buttons to make sure they work. Sometimes, the blank POWER button works when other buttons don’t. If the code works for other buttons, stop here. 10. If the code you entered doesn’t work, do steps 3 through 9 again with another device code from the tables. 11. If you cannot find a code that works, try Setting Up Using Device Code Scan.
Pyramid.book Page 14 Wednesday, February 16, 2005 4:00 PM 7. Press the blank POWER button to turn the device back on. 8. Try some other buttons to make sure they work. Sometimes, the blank POWER button works when other buttons don’t. PROGRAMMING THE REMOTE TO CONTROL A SECOND SATELLITE RECEIVER If you have another DISH Network satellite receiver installed, you can use this remote in AUX mode to control the second receiver.
Pyramid.book Page 15 Wednesday, February 16, 2005 4:00 PM 2. Press the POUND (#) button twice. The mode button flashes the number for each digit of the device code, with a pause between the groups of flashes. A quick flash is for zero. For example, if the code is 570, the mode button flashes five times, pauses, flashes seven times, pauses, and flashes once quickly. For AUX mode, the first group of flashes tells you what the AUX mode controls.
Pyramid.book Page 16 Wednesday, February 16, 2005 4:00 PM 7. Press the plus (+) and minus (-) sides of the VOLUME button. The device’s volume changes and the AUX mode button lights instead of the TV mode button. To set the remote back to control the TV volume: 1. Press and hold the TV mode button for three seconds, and then let go of it. The TV mode button will blink. 2. Press the POUND (#) button. 3. Press the plus (+) side of the VOLUME button. 4. Press the 0 number button. 5. Press the POUND (#) button.
Pyramid.book Page 17 Wednesday, February 16, 2005 4:00 PM OPERATING MODES You can set the remote to four different modes to control the receiver or other devices. You may need to change the remote address to operate the receiver. See Setting Up to Control the Receiver on page 9. You must set up the remote to control a device like a TV, VCR, or DVD player. See Setting Up to Control Other Devices on page 11.
Pyramid.book Page 18 Wednesday, February 16, 2005 4:00 PM POWER BUTTONS Press the blank POWER button to turn the receiver on or off. Press the TV POWER button to turn your TV off and on. Note: You must set up the remote to control the TV for the TV POWER button to work. See Setting Up to Control Other Devices on page 11. VOLUME BUTTON Press this button to raise (+) or lower (-) the TV sound volume. Note: You must set up the remote to control the TV for the VOLUME button to work.
Pyramid.book Page 19 Wednesday, February 16, 2005 4:00 PM GUIDE BUTTON Press this button to open the Program Guide. When you have the Program Guide open, press this button to change between your Favorite Lists. ARROW BUTTONS • Change channels while watching a program- Press the UP or DOWN arrow button. • Open the Browse Banner - Press the RIGHT arrow button. • Show Themes - Press the LEFT arrow button.
Pyramid.book Page 20 Wednesday, February 16, 2005 4:00 PM INFO BUTTON • Program information - Press the INFO button for more information when you watch a program, or when you have the Program Guide, Browse Banner, or Themes list open. • Help - Press the INFO button to see help information when a Help button appears in a menu. VIEW TV BUTTON • When you watch a program, press this button to briefly display the Program Banner.
Pyramid.book Page 21 Wednesday, February 16, 2005 4:00 PM PLAY BUTTON Press the PLAY button to play back a recorded event. Also, press this button to switch from pause, fast forward, or back to normal play back. STOP BUTTON Press the STOP button to stop recording a program or to stop playing a recorded program. PAUSE BUTTON Press the PAUSE button to pause a program. Press this button again to go back to watching the program.
Pyramid.book Page 22 Wednesday, February 16, 2005 4:00 PM BACK BUTTON Press the BACK button to: • Move back through a program four times as fast as normal play. Press this button a second time to move back at 15 times, a third time to move back at 60 times, and a fourth time to move back at 300 times as fast as normal play. • Move back through the program in slow motion. To use this feature, press the PAUSE button and then press the BACK button.
Pyramid.book Page 23 Wednesday, February 16, 2005 4:00 PM POSITION BUTTON Press the POSITION button to move the PIP window to different positions on the TV screen. Each time you press this button, the PIP window moves to a different position. See your receiver user’s guide for more information on using the PIP feature. SWAP BUTTON Press the SWAP button to swap the video in the main display with the video in the PIP window. See your receiver user’s guide for more information on using the PIP feature.
Pyramid.book Page 24 Wednesday, February 16, 2005 4:00 PM 3. If you see the System Info screen, press the SELECT button to close the screen. You have recovered your satellite video. 4. If you do not see the System Info screen, repeat steps 2 and 3 until you have recovered your satellite video. Note: Press any remote control button other than the RECOVER button to end this procedure. DISH BUTTON Press the dish button to go to dish home Interactive TV for receivers that support this feature.
Pyramid.book Page 25 Wednesday, February 16, 2005 4:00 PM STAR BUTTON Press the STAR button to back space while using the search function of your receiver. A high definition satellite receiver may use this button to toggle through the available display modes (Normal, Zoom) for widescreen displays. See your receiver user’s guide for more information. POUND (#) BUTTON Press the POUND button to display the Search screen. Also, you use this button in several procedures in this user guide.
Pyramid.book Page 26 Wednesday, February 16, 2005 4:00 PM POWER BUTTONS Press either POWER button to turn the TV on or off. Note: If you set up the remote to control one TV in TV mode and an additional TV in AUX mode, pressing the TV POWER button controls only the TV you set up in TV mode. MUTE BUTTON Press this button to turn the TV sound on or off. VOLUME BUTTON Press this button to raise (+) or lower (-) the TV sound volume. UP/DOWN ARROW BUTTONS Use these buttons to change channels on the TV.
Pyramid.book Page 27 Wednesday, February 16, 2005 4:00 PM RECALL BUTTON Press this button to go back to the last TV channel you watched. Press it again to switch between the last two TV channels you watched. Note: These buttons do not change the channels on the TV if the remote control is in Limited Mode. NUMBER BUTTONS Use these buttons to directly enter a different channel. Note: These buttons do not change the channels on the TV if the remote control is in Limited Mode.
Pyramid.book Page 28 Wednesday, February 16, 2005 4:00 PM VCR MODE BUTTON You must first set up the remote to control the VCR or DVD player. See Setting Up to Control Other Devices on page 11. Then press the VCR mode button to set the remote to VCR mode. The VCR mode button will stay lit for two seconds to show you’ve set the remote to VCR mode. Make sure you keep the remote in VCR mode to use the buttons we tell you about here. You must put the remote in VCR mode to set it up to control a DVD player.
Pyramid.book Page 29 Wednesday, February 16, 2005 4:00 PM VCR BUTTONS Press the PLAY button to play a videotape or DVD. Press the STOP button to stop playing or recording on a videotape. Press the STOP button to stop playing a DVD. Press the PAUSE button to pause a videotape or DVD. Press this button or the PLAY button to play the tape or DVD. Press the FWD (“forward”) button to forward a videotape or DVD. Press the BACK button to rewind a videotape or reverse a DVD.
Pyramid.book Page 30 Wednesday, February 16, 2005 4:00 PM POWER BUTTON Press the blank POWER button to turn the tuner or amplifier on or off. Press the TV POWER button to turn the TV on or off. MUTE BUTTON Press this button to turn on or off the sound. Note: Program the remote to control the device’s volume by following the instructions on page 15. VOLUME BUTTON Press this button to raise (+) or lower (-) the sound volume.
Pyramid.book Page 31 Wednesday, February 16, 2005 4:00 PM CHANGING FREQUENCIES If you have more than one IR-to-UHF Pro Converter kit in your house, or if you think you are experiencing interference from another source (for example, another remote control), you can change the frequency of the kit. The remote control included with your kit has a switchable key at the bottom that matches the switch on the back of the converter.
Pyramid.book Page 32 Wednesday, February 16, 2005 4:00 PM 5. Turn the key over to match the setting of the switch. 6. Reinstall the key in the remote control. 7. If you have not already installed batteries, install them now. See Installing Batteries for further details. 8. Slide the battery cover back into place.
Pyramid.book Page 33 Wednesday, February 16, 2005 4:00 PM DEVICE CODES These tables contain the manufacturer codes for programming the remote to control a TV, VCR, DVD player, or audio amplifier. Every attempt has been made to include all codes. If your device brand is not listed or if the codes do not work, the remote may not control your device. In some cases codes may operate some but not all buttons. TV CODES TV Programming in AUX mode: Press 0 before entering the TV code.
Pyramid.
Pyramid.
Pyramid.
Pyramid.book Page 37 Wednesday, February 16, 2005 4:00 PM VCR CODES VCR CODES Programming in AUX mode: Finlux 549, 556, 588 Press 1 before entering the VCR code.
Pyramid.
Pyramid.book Page 39 Wednesday, February 16, 2005 4:00 PM VCR CODES STS 678 Sylvania 554, 556, 567, 588, 678, 679 Symphonic 588, 594, 683, 688 Tandy 581, 588 Tashiko 588, 676 Tatung 594, 682 Zenith TV Codes 747 VCR Codes 747 DVD PLAYER CODES Programming in AUX mode: Press 1 before entering the DVD code.
Pyramid.book Page 40 Wednesday, February 16, 2005 4:00 PM DVD Players Panasonic Codes 639, 662, 663, 714, 715, 716, 717, 734 Philips 640, 641 Pioneer 665, 718, 719 Proscan 720 Qwestar 721, 723 RCA 627, 650, 666, 690, 742, 749 TUNER/AMPLIFIER CODES Programming in AUX mode: Press 2 before entering the tuner/ amplifier code.
Pyramid.
Pyramid.book Page 42 Wednesday, February 16, 2005 4:00 PM TROUBLESHOOTING THE KIT What’s Happening What’s Wrong What You Can Do The kit doesn’t work well. That is, when you press a remote control button, either nothing happens or the action you want is repeated. Or, the red light flashes or flickers (maybe very dimly) inside the converter, even though you don’t press any remote button. The converter may be picking up stray UHF signals from other devices nearby.
Pyramid.book Page 43 Wednesday, February 16, 2005 4:00 PM What’s Happening When you press a button on the remote control, the red light flashes inside the converter (but doesn’t stay on) and the receiver doesn’t do what you expect. When you press a button on the remote control, the red light inside the converter doesn’t flash and the receiver doesn’t do what you expect. What’s Wrong What You Can Do • The converter may not be facing the satellite receiver’s front panel.
Pyramid.book Page 44 Wednesday, February 16, 2005 4:00 PM What’s Happening The receiver does things even though you don’t press any remote control buttons. What’s Wrong • The converter may be picking up UHF signals from a neighbor’s remote control or from another UHF Pro remote control in the residence, which may be controlling your receiver. The receiver may be picking up stray IR signals from another DISH Network remote control being used nearby.
Pyramid.book Page 45 Wednesday, February 16, 2005 4:00 PM LIMITED WARRANTY This warranty extends only to the original user (“you,” “your”) of the DISH Network IR-to-UHF Pro Upgrade Kit (“the Kit”) and is limited to the purchase price of the Kit. EchoStar Technologies Corporation and its affiliated companies (“we,” “our,” “us”) warrant the Kit against defects in materials or workmanship as follows.
Pyramid.book Page 46 Wednesday, February 16, 2005 4:00 PM This warranty gives you specific legal rights which may vary from state to state. Some states do not allow the exclusion or limitations of incidental or consequential damages, or allow limitations on the duration of an implied warranty, so those limitations may not apply to you.
Pyramid.book Page 47 Wednesday, February 16, 2005 4:00 PM IF YOU NEED HELP 1. Please review these Instructions. 2. Please see Troubleshoot the Kit on page 42. 3. Call the Customer Service Center at 1-800-333-DISH (3474). Please have the date of purchase and your customer account number ready. 4. A representative will help you. 5. If the rep finds that you should return the Kit, you’ll get a telephone number to call for a Return Authorization (RA) number.
Pyramid.book Page 48 Wednesday, February 16, 2005 4:00 PM REGULATORY FACTORS EchoStar Technologies Corporation, 94 Inverness Terrace East, Englewood CO., (303) 706-4000, declares that: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Pyramid.
Pyramid.
Pyramid.
Pyramid.
inside_back_cover.fm Page 0 Friday, February 11, 2005 4:18 PM Copyright © 2005 EchoStar Technologies Corporation Englewood, Colorado 80112 All rights reserved. The information in these instructions may change without notice. We may issue revisions to tell you about such changes.