User Guide

ManualsBrandsDish ManualsRemote ControlDish 4

REGULATORY FACTORS

WIRELESS REMOTE CONTROL

This device complies with Part 15 of FCC Rules. Operation is subject to the following two

conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Changes or modifications to this device may void your authority to operate this equipment.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the use is encouraged to try to correct

the interference by one or more of the following measures:

• Re-orient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

SAFETY INSTRUCTIONS

You must keep safety in mind while using this device. Keep these

and any other instructions for future reference.

INSTALLATION

Observe Warnings: Carefully follow all warnings on the device

and in the operating instructions.

Heat: DO NOT place the device near heat sources such as radiators, stoves, heat

registers, or other appliances that produce heat.

CARE AND USE

Cleaning: DO NOT use liquid, abrasive, solvent, or aerosol cleaners. Use a damp cloth

for cleaning.

When Not in Use: Remove the batteries if this device is to be

left unattended or unused for a long period of time.

Refer servicing to qualified personnel when a solid object

or liquid has fallen onto or into the device.

DO NOT attempt to service this device. Refer all

servicing to qualified personnel. Opening covers other

than the battery cover will void the warranty.

inside_front_cover_dishnondvr.fm Page 0 Friday, November 4, 2005 2:12 PM

Summary of content (46 pages)

PAGE 1
inside_front_cover_dishnondvr.fm Page 0 Friday, November 4, 2005 2:12 PM REGULATORY FACTORS WIRELESS REMOTE CONTROL This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this device may void your authority to operate this equipment.
PAGE 2
text_dishnondvr.fm Page 1 Monday, November 7, 2005 12:03 PM TABLE OF CONTENTS Remote Control Basics....................................... 2 Models Supported by this Guide ......................... 2 UHF and IR Signals ............................................ 3 Installing Batteries............................................... 3 Converting the 4.0 Remote Control ................... 4 Setting Up to Control the Satellite Receiver ..... 5 Checking the Remote Address ..........................
PAGE 3
text_dishnondvr.fm Page 2 Monday, November 7, 2005 12:03 PM REMOTE CONTROL BASICS This remote control gives you easy access to all the features of a DISH Network satellite TV receiver. You can set up the remote to control the satellite TV receiver and up to three other devices. These devices can be a TV, a VCR or DVD player, and a third device. MODELS SUPPORTED BY THIS GUIDE This user’s guide supports the following remote control models as shown on the label on the back of the remote: • 3.0/3.1/3.
PAGE 4
text_dishnondvr.fm Page 3 Monday, November 7, 2005 12:03 PM INSTALLING BATTERIES The remote control requires AAA batteries. When you replace old batteries, you should replace all of the batteries. Use batteries of the same kind, for example, alkaline or carbon zinc, and don’t mix batteries of different kinds. Alkaline batteries last longer. 1. Press down on the battery cover and slide the cover off. 2. If you are replacing batteries, take out all of the old batteries. 3. Put the new batteries in.
PAGE 5
text_dishnondvr.fm Page 4 Monday, November 7, 2005 12:03 PM CONVERTING THE 4.0 REMOTE CONTROL By replacing the key at the bottom of the 4.0 remote, this remote can be converted to look and work like a 3.0 IR or to operate like a second UHF Pro remote to control the side of the DISH 322 receiver. The instructions below show you how to replace this key. After replacing the key, follow the instructions in Setting Up to Control the Satellite Receiver.
PAGE 6
text_dishnondvr.fm Page 5 Monday, November 7, 2005 12:03 PM 5. If you are converting the remote to operate like a second UHF Pro remote to control the side of the DISH 322 receiver, then get the green 1 UHF Pro key provided separately. Install this key in the remote with the UHF Pro marking showing. Note: Key has the UHF Pro marking. If you set up your DISH 322 to operate the side using UHF Pro, the two UHF Pro remotes for this receiver will interfere with each other when operated at the same time.
PAGE 7
text_dishnondvr.fm Page 6 Monday, November 7, 2005 12:03 PM 1. For DISH 322 receivers only: If you are using a 4.0 Remote control with the green 1 UHF Pro key installed, perform the steps a. through e. below. If not, then go to step 2. a. Open the TV1 UHF Pro Setup screen by pressing MENU-6-1-8 on the remote control. b. Select Enable from the TV1 UHF Pro Setup screen. c. Press the SYS INFO button to open the System Information screen. d.
PAGE 8
text_dishnondvr.fm Page 7 Monday, November 7, 2005 12:03 PM 5. Press the POUND (#) button. If you entered the address correctly, the SAT mode button will flash three times. 6. Press the RECORD button. If you are using the 4.0 remote with the green 1 key (no UHF Pro marking), point the remote control at the receiver when you press the RECORD button. 7.
PAGE 9
text_dishnondvr.fm Page 8 Monday, November 7, 2005 12:03 PM SETTING UP TO CONTROL OTHER DEVICES To use the remote to control other devices (such as a TV, VCR, DVD player, tuner, or amplifier), you must first program it to control these other devices. You can do this by either following the instructions in Setting Up Using Device Code Tables on page 8, or the Setting Up Using Device Codes Scan procedure described on page 9.
PAGE 10
text_dishnondvr.fm Page 9 Monday, November 7, 2005 12:03 PM For example, hold the TV mode button for a TV until all of the other mode buttons light. When you let go, the TV mode light will flash. 4. Only for the AUX mode, Use a number button to enter 0 for a second TV, or 1 for a second VCR or DVD player, or 2 for a tuner or amplifier. 5. Use the number buttons to enter one of the device codes from the table. 6. Only for limited mode, Press 1.
PAGE 11
text_dishnondvr.fm Page 10 Monday, November 7, 2005 12:03 PM 3. Only for the AUX mode, use the number buttons to enter 0 for a second TV, 1 for a second VCR or DVD player, or 2 for a tuner or amplifier. Then press the STAR (*) button. 4. Press the blank POWER button. 5. Press the up or down arrow button until the device turns off. You will have to do this repeatedly to scan through all codes.
PAGE 12
text_dishnondvr.fm Page 11 Monday, November 7, 2005 12:03 PM For AUX mode, the first group of flashes tells you what the AUX mode controls. A quick flash (zero) before the three-digit code is for a TV; one regular flash is for a VCR or DVD player; and two flashes is for a tuner or amplifier. For example, if the TV code is 570, the AUX mode button flashes once quickly, pauses, flashes five times, pauses, flashes seven times, pauses, and flashes once quickly.
PAGE 13
text_dishnondvr.fm Page 12 Monday, November 7, 2005 12:03 PM 2. Press the POUND (#) button. 3. Press the plus (+) side of the VOLUME button. 4. Press the 0 number button. 5. Press the POUND (#) button. The TV mode button flashes three times. 6. Press the SAT mode button. 7. Press the plus (+) and minus (-) sides of the VOLUME button. The TV’s volume changes and the TV mode button lights instead of the AUX mode button.
PAGE 14
text_dishnondvr.fm Page 13 Monday, November 7, 2005 12:03 PM CONTROLLING THE SATELLITE RECEIVER SAT MODE BUTTON Press this button to set the remote to SAT (“satellite”) mode to control the receiver. The SAT mode button’s back light stays lit for about two seconds to show you’ve set the remote to SAT mode. Make sure you keep the remote in SAT mode to use the buttons following buttons. Note: Your satellite receiver may not provide all of the functions described below.
PAGE 15
text_dishnondvr.fm Page 14 Monday, November 7, 2005 12:03 PM MUTE BUTTON Press this button to turn the TV sound on or off. Note: You must set up the remote to control the TV for the MUTE button to work. See Setting Up to Control Other Devices on page 8. MENU BUTTON Press this button to open the Main Menu.
PAGE 16
text_dishnondvr.fm Page 15 Monday, November 7, 2005 12:03 PM ARROW BUTTONS • Change channels - Press the UP or DOWN arrow button to change channels. • Open the Browse Banner - Press the RIGHT arrow button. • Show Themes - Press the LEFT arrow button. • Move around within the Program Guide, menus, and Browse Banner - Press the UP, DOWN, LEFT, and RIGHT arrow buttons. SELECT BUTTON Press this button to select the option you highlight in a menu.
PAGE 17
text_dishnondvr.fm Page 16 Monday, November 7, 2005 12:03 PM VIEW TV BUTTON • When you watch a program, press this button to briefly display the Program Banner. • When you use a menu, press this button to cancel and go back to watch a program. CANCEL BUTTON Press this button to cancel and go back to the previous menu or to watch a program. DISH BUTTON Press the dish button to go to Dish Home for receivers that support Dish Home.
PAGE 18
text_dishnondvr.fm Page 17 Monday, November 7, 2005 12:03 PM Enter menu options - For an option with a number, you can press the number for that option instead of highlighting and selecting the option. • Enter numbers in a blank - Highlight the place where you need to enter the number. Press a number button(s) (or, you can use the UP/DOWN arrow buttons to enter the number). • Search - Use the letters above the NUMBER buttons while in the Search menu.
PAGE 19
text_dishnondvr.fm Page 18 Monday, November 7, 2005 12:03 PM USING THE RECOVER BUTTON Use this procedure works only if you have accidentally changed the TV channel or video input. It does not recover lost satellite signal. Note: RECOVER will first try to tune your TV to channel 3, then channel 4, and then other video inputs with each press of the RECOVER button. You may need to press the RECOVER button up to 30 times to recover your satellite TV video. 1.
PAGE 20
text_dishnondvr.fm Page 19 Monday, November 7, 2005 12:03 PM CONTROLLING A TV (OR A SECOND TV) Only the buttons described here control a TV. Some of the buttons described heremay not control your TV. See your TV user’s manual for information about the TV’s features. You can set up the remote to control a second TV in AUX mode, the same way it controls the first TV in TV mode. See Setting Up to Control Other Devices on page 8. TV MODE BUTTON You must first set up the remote to control the TV.
PAGE 21
text_dishnondvr.fm Page 20 Monday, November 7, 2005 12:03 PM VOLUME BUTTON Press this button to raise (+) or lower (-) the TV sound volume. UP/DOWN ARROW BUTTONS Use these buttons to change channels on the TV. Note: These buttons do not change the channels on the TV if the remote control is in limited mode. SELECT BUTTON The SELECT button works as the ENTER button for a TV. RECALL BUTTON Press this button to go back to the last TV channel you watched.
PAGE 22
text_dishnondvr.fm Page 21 Monday, November 7, 2005 12:03 PM CONTROLLING A VCR (OR A SECOND VCR OR A DVD PLAYER) Only the buttons described here control a VCR or DVD player. Some of the buttons we tell you about here may not control your VCR. See your VCR or DVD player user’s manual for information about the features. You can set up the remote to control a second VCR or DVD player in AUX mode, the same way it controls the first VCR or DVD player in VCR mode.
PAGE 23
text_dishnondvr.fm Page 22 Monday, November 7, 2005 12:03 PM PAGE UP/DOWN ARROW BUTTONS Use these buttons to change channels on the VCR. Note: If you are using the remote control in Limited Mode, the VCR will not change channels. VIEW TV BUTTON For VCR/DVD combinations only: Press the VIEW TV button to switch between VCR and DVD functions. VCR BUTTONS • Press the BACK button to rewind a videotape or reverse a DVD. • Press the PAUSE button to pause a videotape or DVD.
PAGE 24
text_dishnondvr.fm Page 23 Monday, November 7, 2005 12:03 PM CONTROLLING A TUNER OR AMPLIFIER Only the buttons described here control a tuner or amplifier. Some of the buttons described here may not control your tuner or amplifier. See the device user’s manual for information. AUX MODE BUTTON You must first set up the remote to control the device. See Setting Up to Control Other Devices on page 8. Then press the AUX mode button to set the remote to AUX mode.
PAGE 25
text_dishnondvr.fm Page 24 Monday, November 7, 2005 12:03 PM UP/DOWN ARROW BUTTONS Use these buttons to change channels on the tuner or amplifier. SELECT BUTTON This button works as the INPUT SELECT button for the tuner or amplifier.
PAGE 26
text_dishnondvr.fm Page 25 Monday, November 7, 2005 12:03 PM DEVICE CODES These tables contain the manufacturer codes for programming the remote to control your TV, a VCR, DVD player, or audio amplifier. Every attempt has been made to include all codes. If your device brand is not listed or if the codes do not work, the remote may not control your device. In some cases codes may operate some but not all buttons shown in this guide. TV Codes.
PAGE 27
text_dishnondvr.
PAGE 28
text_dishnondvr.
PAGE 29
text_dishnondvr.
PAGE 30
text_dishnondvr.fm Page 29 Monday, November 7, 2005 12:03 PM VCR CODES VCR Programming in AUX mode: In most cases use these codes to program in VCR mode; however, if programming in AUX mode, press 1 before entering the VCR code.
PAGE 31
text_dishnondvr.
PAGE 32
text_dishnondvr.fm Page 31 Monday, November 7, 2005 12:03 PM VCR CODES DVD PLAYER CODES Sylvania 554, 556, 567, 588, 678, 679 Programming in AUX mode: In most cases use these Symphonic 588, 594, 683 Tandy 581, 588 Tashiko 588, 676 Tatung 594, 682, codes to program in VCR mode; however, if programming in AUX mode, press 1 before entering the VCR code.
PAGE 33
text_dishnondvr.
PAGE 34
text_dishnondvr.fm Page 33 Monday, November 7, 2005 12:03 PM Tuner/ Amplifier Codes Yamaha 663, 730, 731, 732, 733, 745, 747 DVD/VCR COMBO CODES Programming for combination equipment: Use VCR mode to control VCR and DVD functions; however, if programming in AUX mode, press 1 before entering the DVD/ VCR code.
PAGE 35
text_dishnondvr.fm Page 34 Monday, November 7, 2005 12:03 PM TROUBLESHOOTING What’s Happening What’s Wrong What You Can Do While you do a remote procedure, the remote control “times out.” • If you don’t press any button for 20 seconds in a programming sequence, the remote “times out.” • If you hold a button longer than two minutes, the remote control stops transmitting to save battery life. Start over again.
PAGE 36
text_dishnondvr.fm Page 35 Monday, November 7, 2005 12:03 PM What’s Happening What’s Wrong What You Can Do When you press a button on the remote control, the device doesn’t do what you expect. • Maybe you’re trying to control a device and you’re not pointing the remote control right at it. • Remember, the remote control uses IR signals to control all devices except for the receiver (when using the UHF antenna). IR signals travel only 40 feet or less, and can’t go through walls or other solid objects.
PAGE 37
text_dishnondvr.fm Page 36 Monday, November 7, 2005 12:03 PM What’s Happening Your UHF Pro remote control does not work well from far away What’s Wrong What You Can Do • You may be experiencing interference from objects near your receiver antenna. • Make sure the UHF antenna is connected to the receiver and not touching anything else. • Vary the tilt angle of the receiver's UHF antenna.
PAGE 38
text_dishnondvr.
PAGE 39
text_dishnondvr.fm Page 38 Monday, November 7, 2005 12:03 PM The shipping charge, for receiving replacement equipment and returning the defective equipment, is a one time fee based on EchoStar's competitive bulk shipping rates (additional charges may apply outside of the continental US). This fee will be charged to your billing account or your valid credit card.
PAGE 40
text_dishnondvr.fm Page 39 Monday, November 7, 2005 12:03 PM IF YOU NEED HELP 1. Review this User Guide. 2. See Troubleshoot the Remote on page 34. 3. Call the Customer Service Center at 1-800-333-DISH (3474). Have the date of purchase and your customer account number ready. 4. A Representative will help you. 5. If the representative finds you should return the remote control, you’ll get a telephone number to call for a Return Authorization (RA) number.
PAGE 41
text_dishnondvr.
PAGE 42
text_dishnondvr.
PAGE 43
text_dishnondvr.
PAGE 44
text_dishnondvr.
PAGE 45
text_dishnondvr.
PAGE 46
inside_back_cover_dishnondvr.fm Page 0 Friday, November 4, 2005 2:13 PM Copyright © 2005 EchoStar Technologies Corporation Englewood, Colorado 80112 All rights reserved. The information in this Guide may change without notice. We may issue revisions to tell you about such changes. Send any comments or questions to: EchoStar Technologies Corporation, Technical Publications, 94 Inverness Terrace East, Englewood, Colorado 80112 Part Number: 142926 Printed in the United States of America.