5.3 Cover.
5.3 Replacement.book Page 1 Friday, November 24, 2006 12:00 PM Table of Contents SETUP AND REFERENCE Quick setup Insert the Batteries ..............................................................S-1 Making the Remote Work with Your Receiver...................S-1 Program the Remote to Control Your TV...........................S-2 Placing Your Remote in Limited Mode...............................S-3 Operation If You Lose Your Picture......................................................S-3 SAT Mode........
5.3 Page S-1.pdf 12/1/2006 11:21:23 AM Quick Setup 1 1 Insert the Batteries 2 3 A Battery A Battery B Battery A B B Battery C Pull the remote battery cover off. Insert 4 AAA batteries making sure to match the plus (+) ends with the plus markings on the battery case. Replace the remote battery cover. M 2 Y CM MY CY CMY Making the Remote Work With Your Receiver 2 1 K Turn your receiver and TV on, and press SYSTEM INFO on the front of the receiver.
5.3 Page S-2.pdf 11/24/2006 11:48:35 AM Quick Setup Program the Remote to Control Your TV 1 2 TV C Turn your TV on. Press & hold the TV Mode button until all Mode buttons light up. 3 4 Press POWER. Press the UP ARROW repeatedly (about 1 M Y CM MY CY CMY press per second) until your TV turns off. K 5 6 # Press POUND. Press the POWER button to turn the TV on and try other buttons to make sure the code works. If you want to try another code, start over from step 1.
.3 Page S-3.pdf 12/1/2006 11:22:45 AM Quick Setup/Operation Placing Your Remote in Limited Mode Limited Mode locks out all the TV mode operations except for TV power, Mute, and Volume. This prevents you from accidentally tuning away from satellite programming. 1 2 PAGE TV Press & hold the TV Mode button until all Mode buttons light up. Press the PAGE UP button. 3 # Press POUND. To take the remote out of Limited Mode, use the PAGE DOWN button instead of the PAGE UP button in step 2.
5.3 Page S-4.pdf 11/24/2006 11:50:06 AM Operation Remote Operation SAT Mode To use the features described in this section, make sure you are in SAT mode by pressing the SAT Mode button. SAT Note: Some features may not be available depending on your receiver model.
5.3 Page S-5.pdf 11/24/2006 11:45:08 AM Operation Remote Operation TV Mode To use the features described in this section, make sure you are in TV mode by pressing the TV Mode button. Remote programming is required. See S-2 for instructions.
5.3 Page S-6.pdf 11/24/2006 11:46:16 AM Operation Remote Operation VCR Mode VCR To use the features described in this section, make sure you are in VCR mode by pressing the VCR Mode button. You can use this mode to operate your DVD player instead of a VCR. Remote programming is required. See page 2 for instructions.
5.3 Replacement.book Page 1 Friday, November 24, 2006 12:00 PM REMOTE CONTROL OVERVIEW Use this full-function remote to control your High Definition DISH Network receiver. Also, you can program the remote to control most of the popular brands of audio/video equipment like a TV, VCR, DVD player, or a second DISH Network satellite receiver. See Programming for Other Equipment on page 2. Note: This remote control may have features not used by your receiver.
5.3 Replacement.book Page 2 Friday, November 24, 2006 12:00 PM If you program the remote to control other equipment, refer to the following for remote control operation instructions: • TVs, page S-5. • VCRs and DVD players, page S-6. • DISH Network satellite receivers, page S-4. • Stereo equipment use only these buttons: SELECT (change inputs), MUTE, VOLUME, and POWER. HOW THE REMOTE COMMUNICATES This remote uses IR signals to control the receiver and other equipment.
5.3 Replacement.book Page 3 Friday, November 24, 2006 12:00 PM you will only be able to use the POWER and VCR function buttons. The section Programming Using the Equipment Code Tables has a step that tells the remote control to go into Limited Mode. Also, a quick way to put the remote in Limited Mode is on page S-3. Note: Limited Mode cannot be used with audio amplifiers.
5.3 Replacement.book Page 4 Friday, November 24, 2006 12:00 PM Instructions Additional Information 7 Press POUND (#). If you entered the code correctly, the mode button flashes three times. 8 Press POWER to turn off the equipment. If the equipment does not turn off, go to step 10. If the code works, the equipment should turn off. 9 Turn the equipment back on and try some other buttons to make sure they work. If the code works for other buttons, stop here.
5.3 Replacement.book Page 5 Friday, November 24, 2006 12:00 PM Instructions Additional Information 3 For AUX mode only. Press 0 for a second TV, or 1 for a second VCR, or 2 for a tuner, or amplifier. Then press the STAR (*) button. This step is for programming which kind of equipment that should be programmed in AUX mode. If you’re not programming in AUX mode, skip to step 4. 4 Press POWER. This puts your remote in the scan mode.
5.3 Replacement.book Page 6 Friday, November 24, 2006 12:00 PM SWITCHING BETWEEN TV AND AMPLIFIER VOLUME CONTROL When you set up the remote to control a TV, the MUTE and VOLUME buttons control the TV volume, even if your remote control is in SAT mode. However, if you want to use the AUX mode to control a tuner or amplifier that has a volume setting, you can set up the remote to control the equipment’s volume instead of the TV volume while your remote control is in SAT mode.
5.3 Replacement.book Page 7 Friday, November 24, 2006 12:00 PM PROGRAMMING THE REMOTE TO CONTROL A SECOND RECEIVER IN AUX MODE If you have another DISH Network satellite receiver installed, you can use this remote in AUX mode to control it along with your new receiver. When you program the remote to control the other receiver, the remote will send out IR signals to the receiver.
5.3 Replacement.book Page 8 Friday, November 24, 2006 12:00 PM READING OUT THE REMOTE CONTROL CODES These instructions explain how to check the remote control code you put in the remote control when you set it up. Be sure to write them in the spaces provided on the inside of the back cover. Instructions 8 Additional Information 1 Press and hold the mode button for the equipment you want the remote to control.
5.3 Replacement.book Page 9 Friday, November 24, 2006 12:00 PM DISCRETE CODES FOR LEARNING REMOTES Remote control discrete On and Off IR commands are used by installers when programming macro commands into universal remotes. Using an On-only or Off-only command is more effective than a toggle On/Off command when trying to ensure the satellite receiver is reliably in one state or the other.
5.3 Replacement.book Page 10 Friday, November 24, 2006 12:00 PM EQUIPMENT CODES These tables contain the manufacturer codes for programming the remote to control your TV, a VCR, DVD player, or audio amplifier. Every attempt has been made to include all codes. If your equipment brand is not listed or if the codes do not work, the remote may not control your equipment. In some cases codes may operate some but not all buttons shown in this guide.
5.3 Replacement.book Page 11 Friday, November 24, 2006 12:00 PM TV CODES (CONTINUED) Jensen 556 573 652 654 JVC 508 557 559 642 649 655 676 726 735 736 737 812 817 Kawasho 548 561 573 652 654 Kenwood 506 573 652 654 656 Kloss 561 610 Kloss Novabeam 657 698 723 724 KTV 526 541 573 657 658 662 696 LG 653 766 Lloyds 627 Lloytron 526 Loewe 566 Logik 675 Luxman 523 652 654 LXI 563 566 590 595 617 631 635 645 646 650 654 683 691 701 725 M.
5.3 Replacement.
5.3 Replacement.
5.3 Replacement.book Page 14 Friday, November 24, 2006 12:00 PM VCR CODES (CONTINUED) Totevision 591 675 676 Unitech 675 Vector Research 534 592 600 Victor 561 562 600 Video Concepts 534 568 592 600 Videosonic 591 675 Wards 534 588 595 675 676 678 XR-1000 588 678 Yamaha 581 592 594 600 682 Zenith 500 501 533 779 DVD PLAYER CODES Programming in AUX mode: In most cases use these codes to program in VCR mode; if programming in AUX mode, press 1 before entering the DVD Player code.
5.3 Replacement.
5.3 Replacement.book Page 16 Friday, November 24, 2006 12:00 PM TV/DVD COMBO CODES Programming for combination equipment: Program the remote control in TV mode using the TV code and then in VCR mode (or AUX - press 1 before entering the DVD code) using the DVD code.
5.3 Replacement.
5.3 Replacement.book Page 18 Friday, November 24, 2006 12:00 PM TROUBLESHOOTING What’s Happening What’s Wrong What You Can Do While doing remote control procedure, the remote control stops working. • If you don’t press a button for 20 seconds in a programming sequence, the remote shuts off its programming function. Start over again. When you press a button on the remote control, the equipment doesn’t do what you expect.
5.3 Replacement.book Page 19 Friday, November 24, 2006 12:00 PM What’s Happening What’s Wrong What You Can Do When you press the remote control Mute or Volume button, nothing happens. • Maybe you have not set up the remote control. • See Programming the Remote to Control Your TV on page S-2 and Programming for Other Equipment on page 2. • Maybe you’re trying to control TV volume but you set up the remote to control a tuner or amplifier in AUX mode.
5.3 Replacement.book Page 20 Friday, November 24, 2006 12:00 PM VOID IF ANY FACTORY-APPLIED IDENTIFICATION MARK, INCLUDING BUT NOT LIMITED TO SERIAL OR CONDITIONAL ACCESS NUMBERS, HAS BEEN ALTERED OR REMOVED. THIS WARRANTY SHALL ALSO BE VOID IF THE DEVICE HAS BEEN OPENED BY AN UNAUTHORIZED PERSON (with the exception of opening the battery cover). This warranty gives you specific legal rights which may vary from state to state.
5.3 Replacement.book Page 21 Friday, November 24, 2006 12:00 PM • replacement remote at our expense. If a defective remote is not covered under the warranty, we will tell you. We may assess you a flat rate charge for a replacement remote, including shipping and insurance. REGULATORY FACTORS This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2.
5.3 Replacement.
5.3 Reference Page.pdf 11/24/2006 11:47:57 AM C M Y MY CY CMY K If you enter a “1” as the last number of your code, your remote is in Limited Mode (see page 2 for more details). CM To read out your remote codes, see page 8 for instructions.
5.3 Back Cover.
