EN User Manual Dishwasher DSF6206W DSF6206X DSF6216X
Contents Safety information Safety instructions Control panel Programs Settings Before first use 2 3 4 5 6 7 Daily use Hints and tips Care and cleaning Troubleshooting Technical information Warranty 7 10 11 12 13 14 Subject to change without notice. Safety information Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible for any injuries or damages that are the result of incorrect installation or usage.
by clients in hotels, motels, bed & breakfast and other residential type environments. Do not change the specification of this appliance. The operating water pressure (minimum and maximum) must be between 0.5 (0.05) / 8 (0.8) bar (kPa) Obey the maximum number of 13 place settings. If the supply cord is damaged, it must be replaced by the manufacturer, its Authorised Service Centre or a similarly qualified persons in order to avoid a hazard.
• • Connect the mains plug to the mains socket only at the end of the installation. Make sure that there is access to the mains plug after the installation. Do not pull the mains cable to disconnect the appliance. Always pull the mains plug. Water connection • • • • Do not cause damage to the water hoses. Before connection to new pipes, pipes not used for a long time, where repair work has been carried out or new devices fitted (water meters, etc.), let the water flow until it is clean and clear.
Indicators Indicator Description End indicator. Multitab indicator. Rinse aid indicator. It is always off while the program operates. Programs Program Degree of soil Type of load Program phases Consumption values 1) Duration (min) Energy (kWh) Water (l) Normal soil Crockery and cutlery • • • • Prewash Wash 50 °C Rinses Dry 129 0.77 11.6 Medium soil Mixed load • • • • Prewash Wash 65 °C Rinses Dry 100 - 120 1.2 - 1.
Settings Program selection mode The appliance is in Program selection mode when all the program indicators come on and the display shows 2 horizontal status bars. When the appliance is in Program selection mode it is possible to set a program. If the control panel does not show this condition, use the Reset function. Reset With Reset you can cancel the running program or the delay start. Press and hold goes back to the Program selection mode.
1. Make sure that the appliance is in Program selection mode. 2. Press and hold at the same time 3. Press . rinse aid dispenser. • • 4. 5. and and go off. until the indicators , and start to flash. continues to flash. The display shows the current setting of the = rinse aid dispenser deactivated. = rinse aid dispenser activated Press to change the setting. Press on/off button to deactivate the appliance and to confirm the setting. Before first use 1. 2. 3. Fill the rinse aid dispenser.
Adding detergent 1 2 If the program has a prewash phase, put a small quantity of detergent on the inner part of the appliance door. Adding multi-tablets 1 2 The Auto Off function This function decreases energy consumption by deactivating automatically the appliance when it is not operating. The function comes into operation: • 5 minutes after the completion of the program. • After 5 minutes if the program has not started.
1. 2. 3. Press the on/off button to activate the appliance. Make sure that the appliance is in program selection mode. Press the button related to the program you want to start. • The related program indicator starts to flash. • The display shows the program duration. Close the appliance door to start the program. • The running program indicator comes on. • The program duration starts to decrease with steps of 1 minute. Option Delay max. 1. 2. 3. Set the program.
Opening the door while the appliance operates If you open the door while a program is running, the appliance stops. When you close the door, the appliance continues from the point of interruption. If the door is opened for more than 30 seconds during the drying phase, the running program will end. Press on/off button or wait for Auto Off to deactivate the appliance. At the end of the program 5 min Press the on/off button to deactivate the appliance.
What to do if you want to stop using multi-tablets Before starting a programme Before you start to use separately detergent and rinse aid do the following procedure. Make sure that: 1. 2. 3. Make sure that the rinse aid container is full. Start the shortest program with a rinsing phase. Do not add detergent and do not load the baskets. Adjust the released quantity of rinse aid. Loading the baskets • • • • • • • • • • • Only use the appliance to wash items that are dishwasher-safe.
C • • • • Make sure that there are no residues of food or soil in or around the edge of the sump. Put back in place the flat filter (C). Make sure that it is correctly positioned under the 2 guides. Reassemble the filters (A) and (B). Put back the filter (A) in the flat filter (C). Turn it clockwise until it locks. An incorrect position of the filters can cause bad washing results and damage to the appliance Cleaning the spray arms Internal cleaning Do not remove the spray arms.
Problem and alarm code The appliance does not drain the water. The display shows • • Make sure that the sink spigot is not clogged. Make sure that the drain hose has no kinks or bends. • Close the water tap and contact an Authorised Service Centre. . The anti-flood device is on. The display shows Possible solution . Once you have checked the appliance, deactivate and activate the appliance. If the problem occurs again, contact an Authorised Service Centre.
Power consumption Off-mode (W) 0.10 1) Refer to the rating plate for other values. 2) If the hot water comes from alternative source of energy, (e.g. solar panels, aeolian energy), use the hot water supply to decrease energy consumption. Rating Plate Information for test institutes For all the necessary information for test performance, send an email to: Mod. ... ... ... Prod. No. ... ... ... Ser. No. ... info.test@dishwasher-production.
6. 7. 8. 9. In all instances, unless the Appliance is transported by Electrolux or an Electrolux authorised representative, the Appliance is transported at the owner’s cost and risk while in transit to and from Electrolux or its ASC. Proof of purchase is required before you can make a claim under this warranty. You may not make a claim under this warranty unless the defect claimed is due to faulty or defective parts or workmanship.
FOR SERVICE or to find the address of your nearest authorised service centre in New Zealand Free call 0800 10 66 10 SERVICE NEW ZEALAND ELECTROLUX (NZ) Limited www.electrolux.co.nz (New Zealand only) FOR SPARE PARTS or to find the address of your nearest state spare parts centre in New Zealand Free call 0800 10 66 20 (New Zealand only) ENVIRONMENTAL CONCERNS dispose of appliances marked with the symbol with the household waste.
www.dishlex.com.
