Quick Start Guide

Dispho
Bluetooth connection
Usage method
Extend the monopod
4
1
2
Open Bluetooth of mobile phone to enter search state and
click “Dispho” in equipment searched; after connection is
nished,Blue light long on。
Mount your phone onto
the sele stick
Charging
5
Non- pan-tilt mode
When the pan-tilt is shut down or out of power, the rotation will
screw tight to the locking direction, the rotation function of the
pan-tilt disappears, and it will become an ordinary tripod sele
stick. (When the rotation is reset to the holder end, the pan-tilt
mode will be restored.)
1
Holder charging mode
2
Charging Mode of Remote Controller
Press the ll light button (optional)
2
Remote controller: Long press photograph key for 3 s,blue lamp will
icker for 3 times and then be off, which means machine is shut down.
Pan-tilt holder: Long press the "on" button for 3 seconds, and the
green light will be off, indicating it is power off.
Powering off
Tips
Open the bottom tripod, uplift the pull rod and put tripod on
horizontal plane.
3
Usage mode of pan-tilt holder
Connect the Micro USB interface of the pan-tilt holder for charging,
and the red light will be on for a long time during the process of
charging；the redlamp will be off automatically
after charging is
nished。
Connect the Micro USB interface charging, and the red light will
be on for a long time during the process of charging；the redlamp
will be off automatically after charging is nished。
1.When the equipment clamps the platform bracket, try to keep the
equipment in the center, if not in the center, it is recommended to use
the vertical scr
een mode.
2.Sele stick will enter sleep mode automatically if it is idled for 10
min after Bluetooth connection; pr
ess photograph key to recover
connection.
3.When using the Remote contr
ol , when the battery is low, the
Remote control will have a ashing red light for reminder. Charge the
sele stick pr
omptly.
4.If the battery is running low, the indicator on the sele stick will
ash r
ed. Charge the sele stick promptly.
5. For any imbalance of the Product after startup due to sharp
change of temperatur
e or humidity, please handle it as follows:
T
urn off the tripod head holder and dismantle it, and then place
it on desktop horizontally as shown in diagram of and
turn it on;
after this, keep pressing the power key for 5 times, and
the holder
will give out 3 short beep sounds followed by 1 long
beep sound;then it will tur
n off automatically and then start again;
by now, the tripod head is recovered to normal status.
Product description
1
3 4
9
8
7
6
5
If you use an Android phone, before taking photos,ensure
that the volume button of your phone is set to the shutter
button in camera settings.
1
4
Micro USB Charging interface
Micro USB interface
Micro USB interface
3
Rotate locking knob
2
Balcony indicator
1
Pan-tilt switch key
8
Photo key
7
Remote Controller Indicator
Tripod
9
2
5
Rotary lock
Aluminum pull rod
6
After clamping the mobile phone
and keeping the phone in natural
balance, then long press the power
button for 3 seconds to turn on the
mobile phone.
Clicking the power button of the
pan-tilt holder, and it will rotate
90 degrees counterclockwise.
After starting up, it will enter the
stable mode, move the holder,
and the mobile phone will always
maintain a constant direction.
90°
Photograph key
Indicator lamp
Yuntai Rotary Locking button
Silicon rubber case for avoiding empty keys
When using the the mobile phone in horizontal screen status, please
use this accessory when the product cannot work normally due to
touching the keys of the mobile phone.
Quick Start Guide
Winners' Sun Plastic & Electronics (Shenzhen)Co., Ltd.
Building E, Yingtai Industrial Zone, Longhua New District,
Shenzhen,China
One Axis Gimbal
Federal Communication Commission (FCC) Radiation
Exposure Statement
The device has been evaluated to meet general RF exposure
requirement, The device can be used in portable exposure
condition without restriction Federal Communication
Commission (FCC) Radiation Exposure Statement Power
is so low that no RF exposure calculation is needed.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2)this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The manufacturer is not responsible for any radio
or TV interference caused by unauthorized modifications
or changes to this equipment. Such modifications or
changes could void the user’s authority to operate the equipment.