Custom Projector Enclosure Installation Manual READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION tel: 303.412.0399 fax: 303.412.9346 www.displaydevices.com tech@displaydevices.com 5880 Sheridan Blvd.
Custom Projector Enclosure Thank you for purchasing this Display Devices product. Our products are designed to be maintenancefree, saving you future service time. If you experience any difficulties, please contact us at 303-4120399. Thank you for your support. It is the responsibility of the dealer installer to ensure this product is properly supported and meets all local building codes. Ensure the ceiling structure is capable of holding at least four times the combined weight of the enclosure (300 lbs.
Custom Projector Enclosure Control Panel There are five parameters to set for your desired operation. Each is set the same way. On the operators panel there are four buttons. The left-most button selects the parameter to adjust (will show current setting). The next button (up arrow) will change the level up, and the next button (down arrow) will change the level down. The last button (most right) will save the level after adjustment. If you do not press the SAVE button, then the changes made will be lost.
Custom Projector Enclosure Installing the Projector NOTE: The projector may be installed into the enclosure prior to hanging the enclosure. It just depends upon the situation you are in. 1. Unlatch door and open to the left (as facing the glass window) 2. To extend the projector cage, loosen the thumbscrew connected to the safety bracket (shown below) and slide the clamp to the left. This will allow you to slide the cage out for easy access. Thumbscrew 3. Use two hands and pull the AVStack cage.
Custom Projector Enclosure Hanging the Enclosure 1. Use the two Unistrut channels on the top of the enclosure to attach to your structural ceiling/truss. We recommend ½” strut hardware. You may attach rated C-Clamps or Cheesboroughs to these structural channels. Structural mounting channel 2. Raise the unit with an equipment lift (or lower truss to enclosure). 3. Tighten all hardware. 4. Bring cabling through the holes on the side of the enclosure – secure both power and signal cables with strain relief.
SHOW POSITION 6. CUSTOMER RESPONSIBLE FOR INSTALLATION TO ANY APPLICABLE CODES/BUILDING REQUIREMENTS. 5. CUSTOMER TO PROVIDE LIQUID/AIR TIGHT FITTINGS AT AC AND VIDEO/CONTROL OPENINGS. 4. POWER REQUIREMENTS: 120VAC, 60HZ, 20A. 3. MAXIMUM ABIENT AIR TEMPERATURE: 100 F. 2. PROJECTOR: SANYO PLC-XF45 (PROVIDED BY CUSTOMER). 1. ESTIMATED UNIT WEIGHT: 280LB (WITHOUT PROJECTOR). NOTES: SERVICE POSITION 6/30/2005, 4:07 PM AX1 REV - ECO 6/30/2005 .XX = .XXX = .
1/2" EMT KNOCK-OUT FOR VIDEO/CONTROL 25.0 1/2" EMT KNOCK-OUT FOR POWER 45.0 21.0 A/C CONDENSATION DRAIN HOLE 20.0 30.0 37.6 FINISH MATERIAL CHECKED DRAWN CRH THE INFORMATION CONTAINED IN THIS DRAWING IS THE PROPERTY OF DISPLAY DEVICES, INC. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF DISPLAY DEVICES, INC IS PROHIBITED 47.0 REAR ACCESS PANEL P1000 UNISTRUT 6/30/2005, 4:07 PM 15.5 SIZE 5880 SHERIDAN BLVD ARVADA, CO 80003 FILE NAME 105-100 105-100.
UNIT EXTENDED FOR SERVICE 85.5 6/30/2005, 4:07 PM CRH THE INFORMATION CONTAINED IN THIS DRAWING IS THE PROPERTY OF DISPLAY DEVICES, INC. ANY REPRODUCTION IN PART OR WHOLE WITHOUT THE WRITTEN PERMISSION OF DISPLAY DEVICES, INC IS PROHIBITED DRAWN CHECKED MATERIAL FINISH UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE IN INCHES. .02 .010 .0050 0.5 6/30/2005 .XX = .XXX = .XXXX = ANGLE = TOLERANCES: DATE DATE TITLE SIZE 5880 SHERIDAN BLVD ARVADA, CO 80003 FILE NAME 105-100 105-100.
Custom Projector Enclosure Temperature Controller with Active AC and Heater RS232 Interface Hardware Standard three pin hookup, 2,3,5, on DB9. Baud rate 9600,N,8,1. No handshaking. Software ASCII letters followed by a delimiter, carriage return (ASCII 13).
