0DT848 • Rev. 01-12-2021 Ditec Sector Reset Handleiding voor installatie, onderhoud, gebruik NL Installation manual, maintenance, use. EN (Vertaling) (Translation) www.ditecdoor.
INHOUDSOPGAVE VAN DE ONDERWERPEN Hoofdst. Onderwerp ............................................................................................................................ Pag. 1. 2. 3. 4. 5. 6. 7. 8. 9. ALGEMENE WAARSCHUWINGEN M.B.T. DE VEILIGHEID ..................................................... 2 TECHNISCHE KENMERKEN ..................................................................................................... 3 MECHANISCHE INSTALLATIE 3.1 Controles doorgangsruimte....................
NL 12 1 2 4 3 13 16 17 15 14 5 18 19 8 9 10 23 6 21 22 20 11 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 7 Beschrijving Bak Motor K10 Aandrijfketting Oprolas Manuele ontgrendelgreep Geleider in polizene bovenste deel Geleider in polizene onderste deel Steun voor bevestiging van geleider SLE (lineaire encoder) Steunveer van geleider Bevestigingsschroef van geleider Riem tegenwicht Ref.
3. MECHANISCHE INSTALLATIE Zie de tekeningen van de mechanische installatie op pagina 26 - 27 (uit te nemen blad in het midden) 3.1 Controles doorgangsruimte (fig.1). • Controleer of de afmetingen van de ruimte overeenkomen met de maten van de geleverde deur, rekening houdend met eventuele noodzakelijke tolerantie indien de installatie binnen de spanwijdte plaats moet vinden. • Controleer of er geen obstakels zijn die de montage van de structuur belemmeren.
NL 4. ELEKTRISCHE AANSLUITINGEN 4.1 Schakelbord • Steek de kabels met de voorbedrade klemmenborden in de behuizing (fig. 14); en sluit ze aan op de kaarten (volgens de aanwijzingen in hfdstk. 5). Plaats de kabels in de kabelgoot en sluit de connectoren op de motor aan (fig.15). De aansluiting van de bedrading moet uitgevoerd worden wanneer de regeleenheid sinds minstens 30 sec. niet onder spanning staat. 4.
49E 5.1 ELEKTRONISCH BEDIENINGSPANEEL 49E - AANSLUITINGEN INGANGEN Commando Functie Beschrijving 1 2 N.O Automatische sluiting De permanente sluiting van het contact maakt de automatische sluiting mogelijk. 1 3 N.O Opening Geleidelijk Met DIP1=ON activeert de sluiting van het contact de openingsmanoeuvre. Met DIP1=OFF activeert de sluiting van het contact een manoeuvre van opening of sluiting in volgorde: opent-stop-sluit-opent. NB.
49E SO NL T T EO EL07L SE 00000000000 FU LS M LK EL07PW1 00000000000 F4 COM LK PRG U W V M B 1 3 9 4 LDV LDR 20 J7 A C LS EO SO RP TC ON ON 1 2 3 4 5 6 - LK + 11 12 17 IN SA POWER NIO 17 14 12 11 0 0 0 1 1 2 3 4 6 8 9 20 41 Rood Wit Bruin Oranje Zwart Blauw A933A L3 L1 Bruin Wit Oranje Blauw Rood Zwart Wit Rosé Rood Bruin Blauw Grijs Geel Groen 9055 L2 1-9 Sluit: Werking met pulscommando 7825A T PWR SA SLE Blauw Zwart Bruin Blauw Bruin 0 1 1 2 3 4 5FB Tx E5
SIGNALEN EN INSTELLINGEN 49E Trimmer TC RP Beschrijving 0s 30 s 0s 30 s Instelling automatische sluitingstijd. Van 0 tot 30 s. NB.: na de activering van het stopcommando, bij het opnieuw sluiten van het contact 1-9, wordt de automatische sluiting alleen in werking gesteld na een commando van volledige, gedeeltelijke of geleidelijke opening. Instelling motor gedeeltelijke opening. Van 0 tot 30 s.
NL 49E EL07L SE 00000000000 www.ditec.it EL07PW1 00000000000 FU F4 ON COM U W V PRG 1 3 9 4 LDV LDR 20 EO SO RP TC ON ON 1 2 3 4 5 6 - LK + 11 12 17 IN SA POWER NIO 17 14 12 11 0 0 0 1 1 2 3 4 6 8 9 20 41 L3 L2 F1 L1 F2 F3 ZEKERINGEN ID Waarden Afmetingen Circuit F1 - F2 - F3 8A - 500V 10.3 x 38 Driefasenleiding F4 3.15A - 230V 5 x 20 Transformator F5 3.15A - 230V 5 x 20 Dynamische rem F6 0.630A - 230V 5 x 20 Rem INSTELLING EINDAANSLAG 1.
52E 5.2 ELEKTRONISCH BEDIENINGSPANEEL 52E (INVERTER) - Aansluitingen INGANGEN Bediening Functie Beschrijving 1 2 N.G. STOP Als op het programmeermenu (pag.15 punt 16) het contact 1-2 vrijgegeven is, hoort bij de opening van het contact ook de STOP van de deur 1 3 N.O. Openen De sluiting van het contact activeert het openen. 1 4 N.O. Sluiting De sluiting van het contact activeert het sluiten. 41 40 N.G.
P1 ON P2 P3 P4 2 3 4 5 6 7 OFF 1 2 3 4 5 6 7 8 S3 Blauw DL P5 Zwart NL 52E S4 M6 M5 LK +F -F U V W OPEN M S5 S2 T °C LK EC M DL SAFETY 15 M7 M4 BACK 1 IN NC C NO 8 4 3 2 1 1 M2 0 LAMP GND L N 230 V Wit Geel Groen Bruin 9038 F1 Het loskoppelen van de bedrading van de absolute encoder veroorzaakt de reset van de posities van de eindschakelaars.
52E REGELINGEN EN MELDINGEN Trimmer P1 P2 P3 P4 P5 Beschrijving 0s 30 s 0s 10 s 0 MAX 0 MAX 0 MAX NIET GEBRUIKT NIET GEBRUIKT NIET GEBRUIKT NIET GEBRUIKT Regeling van displaycontrast. Dip - schakelaar Beschrijving OFF ON DIP 1 Later gebruik – – DIP 2 Toegang tot geavanceerd menu Uitgeschakeld. Vrijgegeven. DIP 3 Vrijgave van trimmers Uitgeschakeld. Vrijgegeven. DIP 4 TOT: Aantal bewegingen SVC: Bewegingen niet uitgevoerd tijdens bediening Uitgeschakeld. Vrijgegeven.
DL P5 52E P1 ON P2 P3 NL P4 2 3 4 5 6 7 OFF 1 2 3 4 5 6 7 8 S3 S4 M6 OPEN M5 ON +F -F U V W S5 S2 DL SAFETY 15 J4 M7 M4 BACK 1 IN NC C NO F1 M3 1 11 12 13 41 40 20 9 8 4 3 2 1 1 F2 GND M2 0 LAMP N 230 V L 50/60 Hz M4A ZEKERINGEN ID Waarden Afmetingen Circuit F1 - F2 12A - 500V 10.
6 PROGRAMMEERMENU 6.1 INSTALLATIEMENU Wanneer het schakelbord wordt aangezet, geeft het toestel de meldingen DITEC en VERSIE FW van microprocessor en kaart weer en opent automatisch het installatiemenu met de melding SEL TAAL. Bevestigen met Tijdens de programmering moeten alle kabels losgekoppeld worden die zijn aangesloten op PIN 3 - 4 - 20 STAP Keuzen 1ste niveau 1 Sel.
NL 6.2 GEAVANCEERD MENU Het geavanceerde menu dient om de positie van de eindschakelaars, die eerder ingesteld werden, te wijzigen en om de ingestelde defaultparameters te wijzigen. Om het geavanceerde menu te openen: - ON Zet de deur in STOP Zet DIP 2 op ON 1 2 3 4 5 6 7 8 Op het display wordt “IJK ENCODER”, het eerste trefwoord van het geavanceerde menu, weergegeven.
STAP Keuzen 1ste niveau Scrollen Bevestigen Keuzen 2de niveau 12 Sluitsnelheid in (Hz) WAARDE WIJZIGEN 13 Activering Alarm Service JA Aantekeningen Grotere waarden instellen moet geëvalueerd worden in functie van de deurafmetingen en van de werkingsomstandigheden.
NL 6.4 Bedieningsmenu (een wachtwoord wordt gevraagd) Met het bedieningsmenu kunt u de drempelwaarden van de remweerstand en de drempelwaarde van de overstroom wijzigen en van de anti-windfunctie op de inwerkingtreding van de encoder.
7. INSTELLING 7.1 Regeling van de veiligheidsinrichting SLE (lineaire encoder) Trimmer Beschrijving R1 MAX MIN LED Acceso / Lampeggiante Er is voeding PWR Dip schakelaar ON 1 2 3 4 0DT848 01-12-2021 Voor 52E positioneer de DIP-schakelaars als volgt: ON Uit Er is geen voeding • Initialisatie • Inwerkingtreding door obstakel Normale activiteit • Test in uitvoering geen obstakel.
NL 8. PROBLEMEN OPSPOREN GEVAAR Alvorens werkzaamheden en werk binnenin de elektronische apparaten uit te voeren, dient u te controleren of de stroomtoevoerleiding losgekoppeld is LET OP De instructies die volgens zijn alleen bedoeld voor gekwalificeerd en bevoegd personeel. Specifieke wetten en bepalingen dienen altijd in acht genomen te worden, ook als dat niet uitdrukkelijk vermeld wordt. Gebruik voor reparaties en vervangingen altijd en alleen originele reservedelen van Ditec.
9. ONDERHOUDSSCHEMA ELKE 6 MAANDEN Er moeten regelmatig inspecties worden uitgevoerd, met inachtneming van de geldende landelijke voorschriften en van de productdocumentatie, door gekwalificeerde en door Ditec opgeleide technici. De frequentie van de onderhoudswerkzaamheden moet voldoen aan de geldende landelijke voorschriften en aan de productdocumentatie.
NL AANWIJZINGEN VOOR GEBRUIK EN ONDERHOUD LOSMAKEN EN ONVERHANDIGEN AAN DE GEBRUIKER ALGEMENE WAARSCHUWINGEN M.B.T. DE VEILIGHEID Deze handleiding maakt integraal en essentieel onderdeel uit van het product en moet overhandigd worden aan de gebruiker van het product. Dit document moet bewaard worden en overhandigd worden aan eventuele volgende gebruikers van het systeem.
9. ONDERHOUDSSCHEMA ELKE 6 MAANDEN Er moeten regelmatig inspecties worden uitgevoerd, met inachtneming van de geldende landelijke voorschriften en van de productdocumentatie, door gekwalificeerde en door Ditec opgeleide technici. De frequentie van de onderhoudswerkzaamheden moet voldoen aan de geldende landelijke voorschriften en aan de productdocumentatie.
NL GEBRUIKSAANWIJZINGEN Bedieningscategorie 5 (minimum 5 jaren van bedrijf met 600 cycli per dag) Gebruik: ZEER INTENS (voor industriële en commerciële ingangen met zeer intens gebruik) • De bedieningscategorie, de gebruikstijden en het aantal opeenvolgende cycli geven alleen een algemeen idee. Ze werden op statistische wijze gemeten in gemiddelde gebruiksvoorwaarden en zijn niet zeker voor elk afzonderlijk geval.
INSTRUCTIES VOOR HERSTEL VAN DOEK MET NOODUITGANG 1 4 5 2 6 STOP A 3 C 1m 0DT848 01-12-2021 - 24 - B
NL LIJST VAN BESTANDDELEN Referentie Beschrijving Hoeveelheid A Linkerstijl 1 B Rechterstijl 1 C Oprolas 1 D Tegenwicht 1 E Schakelbord 1 F Doos met hulpstukken 1 D B A E C F - 25 - 0DT848 01-12-2021
TEKENINGEN VAN MECHANISCHE INSTALLATIE 1 475 200 300 400 15 50 200 1800 PH HT H R standard (Top) 115 PL 25 LT 185 25 190 300 140 L PL PH min 900 1700 max 6000 5000 515 3 4 Ø 8 mm 8 9 Ø 8 x 20 Ø 4,5 13 ≥ 1,8 m 6 39 27 Ø 4,5 10
MECHANICAL INSTALLATION DRAWINGS 2 A B C C X C H A Y 1/2H LT 6 5 7 200 12 11 13 E X F D ~ 0,5 m
EN PACKING LIST Reference Description Quantity A Left column 1 B Right column 1 C Transom with rolled curtain 1 D Counterweight 1 E Control unit 1 F Hardware box 1 D B A E C F 0DT848 01-12-2021 - 28 -
EN EMERGENCY EXIT – RESTORE CURTAIN INSTRUCTION 1 4 5 2 6 STOP A 3 C 1m - 29 - B 0DT848 01-12-2021
CONTENTS Chap. Topic ..................................................................................................................................... Page 1. 2. 3. GENERAL SAFETY PRECAUTIONS ....................................................................................... 30 TECHNICAL CHARACTERISTICS ........................................................................................... 31 MECHANICAL INSTALLATION 3.1 Checking the opening ....................................................
EN 12 1 2 4 3 13 16 17 15 14 5 18 19 8 9 10 23 6 21 22 20 11 Ref. 1 2 3 4 5 6 7 8 9 10 11 12 7 Description Transom Motor K10 Transmission chain Rolling shaft Manual release lever Polyzene guide upper section Polyzene guide lower section Fixing plate of the guide Linear Encoder (SLE) Supporting spring Fixing screw Belt counterweight Ref.
3. MECHANICAL INSTALLATION See the relevant drawings of the mechanical installation at page. 26 - 27 (central sheet to be removed). 3.1 Checking the opening (fig.1). • Check the dimensions of the opening, and their correspondence to the overall dimensions of the door supplied, taking into consideration any necessary tolerances in the case of installation in an archway. • Check that no existing structures obstruct the assembly of the door.
EN 4. ELECTRICAL CONNECTIONS 4.1 Electrical panel • Insert the cables with the pre-wired terminal boards in the housing (fig. 14) and connect them to the boards (as shown in chap. 5). Fit the cables in the conduit and connect the connectors on the motor (fig.15). Cabling connection on the board must be done with main power cut off, for at least 30 sec. 4.
49E 5.1 49E ELECTRONIC CONTROL PANEL - CONNECTIONS INPUTS Command Function Description 1 2 N.O Automatic closing Permanently closing the contact enables automatic closing. 1 3 N.O Opening With DIP1=ON the closure of the contact activates an opening operation. Step-by-step With DIP1=OFF the closure of the contact activates an opening or closing operation in the following sequence: open-stop-close-open.
49E SO EN T T EO EL07L SE 00000000000 FU LS M LK EL07PW1 00000000000 F4 COM LK PRG U W V M B 1 3 9 4 LDV LDR 20 J7 A C LS EO SO RP TC ON ON 1 2 3 4 5 6 - LK + 11 12 17 IN SA POWER NIO 17 14 12 11 0 0 0 1 1 2 3 4 6 8 9 20 41 Red White Brown Orange Black Blue A933A L3 L1 Brown White Orange Blue Red Black White Pink Red Brown Blue Gray Yellow Green 9055 L2 1-9 To close: Operation by pulse command 7825A T PWR SA SLE Red Orange Blue Black White Black Brown Blue Grey
SIGNALS AND SETTING 49E Trimmer TC RP Description 0s 30 s 0s 30 s Setting automatic closing time. From 0 to 30 s. Note: after the activation of the stop command, once contact 1-9 has closed again, the automatic closing is only activated after a total, partial or step-by-step opening command. Motor partial opening adjustment. From 0 to 30 s. Dip - switch Ditec Sector Reset Dip-switches setting ON 1 2 3 4 5 6 Jumpers Description OFF ON DIP 1 Control 1-3 function.
EN 49E EL07L SE 00000000000 www.ditec.it EL07PW1 00000000000 FU F4 ON COM U W V PRG 1 3 9 4 LDV LDR 20 EO SO RP TC ON ON 1 2 3 4 5 6 - LK + 11 12 17 IN SA POWER NIO 17 14 12 11 0 0 0 1 1 2 3 4 6 8 9 20 41 L3 L2 F1 L1 F2 F3 FUSES ID Value Dimension Circuit F1 - F2 - F3 8A - 500V 10.3 x 38 Three phase line F4 3.15A - 230V 5 x 20 Transformer ADJUSTMENT LIMIT SWITCH 1.
52E 5.2 52E CONTROL PANEL (INVERTER) - Connections INPUTS Command Function Description 1 2 NC STOP If on the programming menu (page 15 point 16) Contact 1-2 enabled, opening of the contact STOPS the door 1 3 NO Opening The closure of the contact activates the opening operation. 1 4 NO Closure The closure of the contact activates the closing operation.
P1 ON P2 P3 P4 2 3 4 5 6 7 OFF 1 2 3 4 5 6 7 8 S3 Blue DL P5 Black EN 52E S4 M6 M5 LK OPEN M +F -F U V W S5 S2 T °C LK EC M DL SAFETY 15 M7 M4 BACK 1 IN NC C NO 8 4 3 2 1 1 M2 0 LAMP GND L N 230 V White Yellow Green Brown 9038 F1 When the absolute encoder wiring is disconnected, the positions of the limit switches are reset.
52E ADJUSTMENTS AND SIGNALS Trimmer P1 P2 P3 P4 P5 Description 0s 30 s 0s 10 s 0 MAX 0 MAX 0 MAX NOT USED NOT USED NOT USED NOT USED Adjustment of display contrast. Dip-switches Description OFF ON DIP 1 Future use – – DIP 2 Access to advanced menu Disabled.
DL P5 52E P1 ON P2 P3 EN P4 2 3 4 5 6 7 OFF 1 2 3 4 5 6 7 8 S3 S4 M6 OPEN M5 ON +F -F U V W S5 S2 DL SAFETY 15 J4 M7 M4 BACK 1 IN NC C NO F1 M3 1 11 12 13 41 40 20 9 8 4 3 2 1 1 F2 GND M2 0 LAMP N 230 V L 50/60 Hz M4A FUSES ID Value Size Circuit F1 - F2 12A - 500V 10.
6 PROGRAMMING MENU 6.1 Installation menu When the control panel is switched on, after showing the messages DITEC and microprocessor and card FW VERSION, the device automatically enters the installation menu and displays the message SELECT LANGUAGE.
EN 6.2 Advanced menu The advanced menu allows you to modify the position of the limit switches which have previously been set and modify the set default parameters. To access the Advanced Menu: - STOP the door Set DIP 2 to ON ON “ENCODER CALIB.”, the first item in the advanced menu, will appear on the display.
STEP 1st level options Scrolling Confirm 2nd level options Notes The setting of higher values must be assessed according to door dimensions and operating conditions. 12 Closing speed in (Hz) CHANGE VALUE 13 Enable service alarms YES NO RESET? Restart the service count down Option available only if YES has been selected for point 14). Set value to steps of 1000 cycles Max 200,000 cycles If set to YES, opening of the contact 1-2 STOPS the door.
EN 6.4 Service menu (password required) The Service menu is used to modify the brake resistance thresholds, the overcurrent threshold and the anti-wind function when the encoder intervenes. To access the Service menu: - STOP the door Set DIP5 to ON Enter the PW: button sequence OPEN- OPEN- CLOSE- PARTIAL OPENING ON 1 2 3 4 5 6 7 8 Remove cables from PIN 3, 4, 20 during programming STEP 1st level options Notes 1 MIN BRAKING VOLT.
7. ADJUSTING AND STARTING 7.
EN 8. TROUBLESHOOTING DANGER Before performing and operations and working on the electronic equipment make sure that the power supply has been disconnected WARNING The following instructions are for qualified and authorised personnel only. Specific laws and standards must always be complied with even when not expressly indicated. For repair work or replacements, use only original Ditec spare parts.
9. MAINTENANCE TO BE CARRIED OUT EVERY 6 MONTHS Regular inspections should be made according to national regulations and product documentation by a Ditec trained and qualified technician. The number of service occasions should be in accordance with national requirements and with the product documentation.
EN USE INSTRUCTIONS GENERAL SAFETY PRECAUTIONS This user handbook is an integral and essential part of the product and must be delivered to the users. Keep this document and pass it on to any future users. This automation is a “vertical-roll door”; it must be used for the specific purpose for which it was designed. Any other use is to be considered inappropriate and so dangerous. Assa Abloy Entrance Systems AB declines all responsibility for damage caused by improper, incorrect or unreasonable use.
9. MAINTENANCE TO BE CARRIED OUT EVERY 6 MONTHS Regular inspections should be made according to national regulations and product documentation by a Ditec trained and qualified technician. The number of service occasions should be in accordance with national requirements and with the product documentation.
EN APPLICATIONS Use: 5 (minimum 5 years of working life with 600 cycles a day) Applications: HEAVY DUTY (for industrial and commercial access with heavy duty use). • Service class, running times, and the number of consecutive cycles are to be taken as merely indicative having been statistically determined under average operating conditions, and cannot therefore be applied to each individual case. Reference is to the period when the product functions without the need for any extraordinary maintenance.
0DT848NLEN - 01-12-2021 Ditec C/O Dynaco Europe n.v.