- Dixon Industrial Lawn Mower User Manual

ManualsBrandsDixon Marking Tools ManualsLawn MowerTECHNICAL DATA BROCHURE ZTR 4422

DIXON INDUSTRIES, INC

A BLOUNT COMPANY

AIRPORT INDUSTRIAL PARK

PO BOX 1569

COFFEYVILLE KS 67337 0945

316 251 2000

FAX 316 251 4117

TECHNICAL DATA BROCHURE

ZTR 4421 & 4422

IMPORTANT: READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS

DELUXE SEAT ADJUSTMENT:

Raise upper body to fully open position by lifting on arm rest and seat back. Loosen seat

adjustment knobs under seat frame. Slide seat to desired setting and fully tighten seat

adjustment knobs.

Caution: DO NOT

Operate mower unless seat adjustment knobs are fully tightened.

Page 1 of 13

REMOVING THE BODY:

Summary of content (13 pages)

PAGE 1
DIXON INDUSTRIES, INC A BLOUNT COMPANY AIRPORT INDUSTRIAL PARK PO BOX 1569 C O F F E Y V I L L E K S 6 7 3 3 7 0945 316 251 2000 FAX 316 251 4117 TECHNICAL DATA BROCHURE ZTR 4421 & 4422 IMPORTANT: READ OPERATOR'S MANUAL BEFORE OPERATING OR MAKING ADJUSTMENTS DELUXE SEAT ADJUSTMENT: Raise upper body to fully open position by lifting on arm rest and seat back. Loosen seat adjustment knobs under seat frame. Slide seat to desired setting and fully tighten seat adjustment knobs.
PAGE 2
1. Both the 4421 & 4422 use a two piece body. The upper body can be raised up and back, and also tilted forward to expose the transaxle. 2. To remove upper body, lift up and fold forward. Disconnect throttle cable P/N 4679 from engine. Disconnect wiring harness by simply pulling plug apart. Then clip wire ties so harness is loose from seat bracket. Next remove cotter key P/N 3052 from upper body mounting pin P/N 1460. Then hold upper body and remove pin P/N 1460. 3. Reverse above procedure to reinstall.
PAGE 3
MOWER BLADE OPERATION: 1. To start mower blades, pull up slightly on blade drive switch handle and move it forward to the "ON" position. 2. To stop mower blades, move switch handle to the "OFF" position. SAFETY CHECKS IMPORTANT - PERFORM SAFETY CHECKS AFTER MAKING ANY REPAIRS OR ADJUSTMENTS 1. After reassembly, while seated on mower, attempt to start engine with mower deck engaged. Engine should not start. If engine does start, return the mower to an Au thorized Dixon dealer for adjustment or repair. 2.
PAGE 4
THE FOLLOWING INSTRUCTIONS REFER TO 42" MOWER DECKS: INSTALLATION: 1. Position mower deck assembly under frame, raise front of mower deck assembly enough to allow cross shaft P/N 1332 to slide through frame guides and mower deck guides. Install (2) washers P/N 3094 and (1) hair pin cotter P/N 3072 on each end of the cross shaft. 2. Attach short L-rod P/N 1355 to lift arm as shown in drawing. 3. Attach long L -rod P/N 1409 to rear lift arms as shown in drawing.
PAGE 5
4. NOTE: It is possible to install the engine to mower deck drive belt P/N 6111 at this time; however, our engine manufacturers have suggested that this belt be installed after the engine has been fully serviced per manufacturers' suggestions and allowed to o perate at 1 /2 to 3/4 throttle settings for approximately (3) minutes. This will place the initial start up of the engine in a no load situation and allow complete engine lubrication. ADJUSTMENT: 1. Install engine to mower deck drive belt P/N 6111. 2.
PAGE 6
4421 BODY ASSEMBLY
PAGE 7
4422 BODY ASSEMBLY
PAGE 8
4421 CHASSIS ASSEMBLY
PAGE 9
4422 CHASSIS ASSEMBLY
PAGE 10
4421 /4422 TRANSAXLE ASSEMBLY
PAGE 11
4421/4422 MOWER DECK ASSEMBLY
PAGE 12
4421 WIRING ASSEMBLY
PAGE 13
4422 WIRING ASSEMBLY