Quick start Guide

10
11
12
13
1
3
9
5
7
15
4
7
6
7
5
6
6
8
2
* The maximum flight speed and maximum run time (hovering state) were tested in a lab environment, at zero-level elevation and in windless conditions, and
should be taken as reference only.
7
.1
6 inc
h
6
.
77
in
c
h
4.14 inch
2.80 inch
Return to home
Vision Positioning
Altitude 3 m
●
Calibrating the Compass:
Make sure to calibrate the compass in every new flight location. The compass is very sensitive to electromagnetic interference,
which can cause abnormal compass data leading to poor flight performance or even failure. Regular calibration is required for
optimum performance.
●
DO NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking
structures, and steel reinforcements underground.
●
DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones.
●
DO NOT calibrate beside massive metal objects.
●
If it is blinking red and yellow alternately after placing the aircraft on the ground, the compass has detected magnetic
interference. Change your location.
Always
fly under
400 ft
●
While returning home, its altitude can be adjusted by the user to avoid obstructions. Tall buildings may affect the remote controller signal. The
Failsafe Return to Home procedure will be triggered if the signal is lost. Be sure fly higher than any nearby buildings to avoid crashing.
●
P Mode:
In this mode, the Inspire 1 has a strong GPS signal and can use the
VPS allowing it to hover accurately in position indoors and out. If
outdoors, this mode also means that a Home Point has been
locked so that it can Return to Home if the control signal is lost.
There are three states in P mode.
P-GPS: GPS works best when outdoors in a wide open area, and
your Inspire 1 uses GPS to hover in place when the GPS signal is
strong. P-OPTI: If GPS is not available, the aircraft can use the
VPS to hover accurately. P-ATTI: Neither GPS or VPS available,
aircraft is using only its barometer for positioning, so only altitude
is controlled. Note that the VPS may not work properly when the
Inspire 1 is flying over water, over surfaces without a clear pattern,
or in a low light environment.
If you are not in this mode, toggle the Flight Mode
Switch to P position to enable it.
The Flight Mode Switch is locked in P mode by default.
Refer to the User Manual on how to unlock the switch.
●
Return to Home:
When the GPS signal is strong, the aircraft will be
able to record a Home Point and return to the Home
Point when needed. The GPS location is recorded
when the GPS signal icon in the DJI GO app is either
yellow or green.
The aircraft will return to the Home Point automatically in
the following cases (all require a strong GPS signal).
Smart RTH: When you press the RTH button on the
remote controller or in the App. Low Battery RTH: The
DJI GO app notifies users to take action when the
battery level falls to a specified threshold.
Failsafe RTH: When the remote controller signal is lost.
DO NOT FLY in rain, snow, fog, and wind
speeds exceeding 22 mph or 10 m/s.
It is important to understand basic
flight guidelines, for the safety of
both you and those around you.
Refer to the Safety Guidelines and
Disclaimer for more information.
DO NOT FLY near or above people, near
trees, power lines or buildings.
More information at:
http://flysafe.dji.com/no-fly
No Fly Zones
DO MONITOR YOUR ALTITUDE
and fly under 400 feet
(120 meters).
DO MAINTAIN LINE OF SIGHT
and avoid flying behind buildings
or obstacles that block your view.
DJI encourages you to enjoy flying in a safe, responsible and smart way.
●
Be very careful when flying 14,700 feet (4,500 meters) or more above sea level as the battery and aircraft performance may be reduced.
●
The Inspire 1’s compass and GPS will not work in Polar Regions. The aircraft will auto switch to ATTI Mode and use the VPS for positioning.
GPS Positioning
Fly Safe
11. Gimbal Dial
12. Camera Settings Dial
13. Video Recording Button
14. Flight Mode Switch
15. Shutter Button
16. Playback Button
17. Mini-HDMI Port
18. Micro-USB Port
19. CAN-Bus Port
20. USB Port
21. Back Buttons (Reserved)
10
4
9
9
8
4
5
6
1
3
7
2
21
17 18 19
20
11
14
13
12
1615
Quick Start Guide
INSPIRE 1
The Inspire 1 is a professional aerial filmmaking and photography platform that is ready to fly right out of the box. Featuring
an onboard camera equipped with a 20mm lens and 3-axis stabilized gimbal, it shoots sharp 12mp stills and stable video at
up to 4K. Its retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world
below.
An advanced flight controller makes the Inspire 1 stable, safe and easy to fly indoors or out. The brand new Vision
Positioning System (VPS) gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight
controllers, it is also able to return home if remote controller signal is lost or if the low battery warning is triggered.
The Inspire 1 boasts a maximum flight speed 20m/s* and a maximum flight time of 18.5 minutes* using one fully charged
4500mAh Intelligent Flight Battery.
The maximum transmission distance of the Inspire 1 remote controller is 2km*. The remote controller also allows you to
control the landing gear or activate Return to Home with a tap. Other buttons allow instant photo capture, video recording,
picture review and gimbal control.
A DJI Lightbridge-based HD video downlink is built-in, letting you see what your camera sees on your mobile device in
real time HD. The app also allows you to change camera settings and activate Master/Slave mode so that one person
can fly while other controls the gimbal independently. The master and slave controllers communicate using a 5.8Ghz
wireless signal, and have a communication range with each other of up to 50 meters.The controller’s LiPo battery has
a maximum run time of approximately four hours and can be charged by plugging directly into the controller.
1. Power Button
2. Transformation Switch
3. Return to Home (RTH) Button
4. Control Sticks
5. Status LED
6. Battery Level LEDs
7. Power Port
8. Mobile Device Holder
9. Antennas
10. Handle Bar
* Please note that the max transmission distance were tested in a lab environment. This statistic is for reference only, as conditions in your area may vary.
INSPIRE 1 Remote Controller
Folded
Appendix
V2.2
●
Aircraft (Model: T600)
Weight 2845 g (Battery and Propellers Included, Zenmuse X3 Excluded)
Weight 3060 g (Battery, Propellers and Zenmuse X3 Included)
Maximum Weight of Payload 3500 g
Max Tilt Angle 35°
Max Ascent Speed 5 m/s
Max Descent Speed 4 m/s
Max Speed 20 m/s (ATTI mode, no wind)
Max Altitude Above Sea Level 14,700 feet (4,500 meters)
Max Flight Time Approximately 18.5 minutes
Operating Temperature Range 14° to 104° F (-10° to 40° C)
●
Gimbal (Model: ZENMUSE X3)
Angular Vibration Range ±0.03°
Controllable Range Pitch: -90° to +30° Pan: ±320°
Max Controllable Speed Pitch: 120°/s Pan: 180°/s
●
Vision Positioning System
Velocity Range <8 m/s @Altitude 6.56 feet (2 m)
Altitude Range 0.16 feet - 16.4 feet (5 cm-500 cm)
Operating Range <9.84 feet (<300 cm)
Operating Environment Surface with clear pattern and adequate lighting (>15 Lux )
●
Camera (Name/Model: X3/FC350)
Sensor Sony Exmor R CMOS (Type 1/2.33), Effective pixels: 12.4M (total pixels: 12.76M)
Lens FOV (Field Of View) 94° 20 mm (35 mm format equivalent) f/2.8
ISO Range 100-3200 (video) 100-1600 (photo)
Electronic Shutter Speed 8 s-1/8000 s
Image Max Size 4000×3000
Still Photography Modes Single shoot; Burst shooting: 3/5/7 frames
Auto Exposure Bracketing (AEB): 3/5 bracketed frames at 0.7EV Bias; Time-lapse
Video Recording Modes UHD: 4K (4096×2160) 24/25p, 4K (3840×2160) 24/25/30p,
FHD: 1920×1080 24/25/30/48/50/60p, HD: 1280×720 24/25/30/48/50/60p
Max Bitrate Of Video Storage 60 Mbps
Supported File Systems FAT32 (≤ 32 GB), exFAT (> 32 GB)
Photo Formats JPEG, DNG
VideoFormats MP4/MOV (MPEG-4 AVC/H.264)
Supported SD Card Types Micro SD, Max capacity: 64GB. Class 10 or UHS-1 rating required
Operating Temperature Range 32° to 104° F (0° to 40° C)
●
Remote Controller (Name: C1)
Operating Frequency 922.7 MHz-927.7 MHz (Japan only) 5.725 GHz-5.825 GHz 2.400 GHz-2.483 GHz
Transmitting Distance Up to 5 km or 3.1 miles (unobstructed, free of interference) when FCC compliant
Up to 3.5 km or 2.1 miles (unobstructed, free of interference) when CE compliant
Video Output Port USB, Mini-HDMI
Operating Temperature Range 14° to 104° F (-10° to 40° C)
Battery 6000 mAh LiPo 2S
●
Charger (Model: A14-100P1A)
Voltage 26.3 V
Rated Power 100 W
●
Intelligent Flight Battery (Model: TB47, Standard)
Capacity 4500 mAh
Voltage 22.2 V
Battery Type LiPo 6S High voltage battery
Energy 99.9 Wh
Net Weight 570 g
Operating Temge 14° to 104° F (-10° to 40° C)
Max Charging Power 180 W
●
Intelligent Flight Battery (Model: TB48, Optional)
Capacity 5700 mAh
Voltage 22.8 V
Battery Type LiPo 6S High voltage battery
Energy 129.96 Wh
Net Weight 670 g
Operating Temge 14° to 104° F (-10° to 40° C)
Max Charging Power 180 W
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
※ This Quick Start Guide is subject to change without prior notice.
Landing Mode
Travel Mode
Flight Mode
Landing Gear Up Landing Gear Down
1. Gimbal and Camera
2. Camera Micro-SD Card Slot
3. Vision Positioning System
4. Transformation Mechanism
5. Front LEDs
6. Motors
7. Propellers
8. Rear LEDs
9. Intelligent Flight Battery
10. Power Button
11. Battery Level Indicators
12. Aircraft Status Indicator
13. Aircraft Micro-USB Port
14. Camera Micro-USB Port
15. Gimbal Lock
Connect to the
mobile device
21
1
7
.2
4
i
nch
11.85 inch
1
7
.
7
6
i
n
c
h
14