Quick start Guide

U
P
D
o
w
n
T
u
r
n
R
i
g
h
t
T
u
r
n
L
e
f
t
F
o
r
w
a
r
d
B
a
c
k
w
a
r
d
R
i
g
h
t
L
e
f
t
Left Stick
Right Stick
●
You can change the stick mode in the DJI GO app.
9. Controls
The stick mode is set to Mode 2 by default (left hand throttle). The left stick controls the aircraft's elevation and heading.
The right stick controls the aircraft's forward, backward and lateral movements. The gimbal dial controls camera tilt.
Gimbal Dial
Downloading Your VideosRemote Controller Status Indicator
Appendix
Return-to-Home (RC)
OR
In the DJI GO App:
10. Flight
slowly
. . .
Safe to fly (GPS working).
RC normal but not connected to aircraft.
RC normal and connected to aircraft.
RC Slave Mode and connected to aircraft.
RC Slave Mode and not connected to aircraft.
Manual Takeoff Manual Landing
Left stick down (slowly)
until you touch the ground.
Hold a few seconds to
stop the motors.
●
The aircraft will not avoid obstacles while it is returning to the
Home Point, and an appropriate RTH altitude must be set before
takeoff. You should also use the control sticks to guide the aircraft.
Refer to the Safety Guidelines and Disclaimer for more details.
If you want to lower the landing gear
but the switch is already in the
'down' position, toggle the switch
up and down again.
LowerRaise
●
Rotating propellers can be dangerous. DO NOT start the motors in narrow spaces or when there are people nearby.
●
Never perform the Combination Stick Command in mid-flight, or else the aircraft will crash.
●
Always keep your hands on the remote controller so long as the motor is still spinning.
●
After landing, power off the aircraft before turning off the remote controller.
●
Take off from a flat surface in a wide open space, with the rear of the aircraft facing towards you.
Same as the RTH button in the DJI GO app.
Brings the aircraft back to the Home Point.
Press and hold to initiate the RTH procedure.
Press again to cancel.
Aircraft Status Indicator
slowly
. . .
P-ATTI or ATTI mode.
slowly
. . .
Low battery level warning.
quickly
.....
Critical low battery level warning.
solid —— Critical error.
. . .
No GPS but VPS working.
● Compressed video and photo files
are automatically stored on your
mobile device while you are
recording. You can view them in the
Library section of the DJI GO app.
● For the best quality, download the
original HD files through the app or
using an SD card reader.
Safe to Fly (GPS)
Before taking off, ensure the Aircraft Status Bar in the DJI GO app
indicates ‘Safe to Fly (GPS)’.
Auto Takeoff
The aircraft will take off and hover at
an altitude of 4 feet (1.2 meters).
Return-to-Home
Brings the aircraft back to the Home
Point. Tap again to stop the procedure.
Auto Landing
The aircraft will land vertically and stop its
motors.
Combination Stick Command
to start/stop the motors
Left stick up (slowly)
to take off
Ensure the landing gear is lowered
before landing.
quickly
.....
Not connected to remote controller.
. . .
compass calibration required.
※ This content is subject to
change without prior notice.
( B
...
) Low battery warning / RC error.
( B—B—
...
) RC idle for 5 minutes.
8. Preparing for Takeoff
Toggle the Flight Mode
Switch to the safest P-Mode.
Connect your mobile
device.
Power on the remote
controller and aircraft.
Launch the DJI GO app
and enter Camera View.
Calibrate the compass.
Tap the Aircraft Status Bar at
the top, select 'Calibrate'
and follow the on-screen
instructions.
DJI GO
App
Pair the propellers and
motors with arrows of the
same color (red or white).
Attach the
propeller onto the
motor.
2
●
Ensure the propellers are mounted securely and correctly.
1
Rotate the
propeller lock until
the arrows are
aligned and you
hear a click.
3
Again, rotate the
propeller lock until
you hear a click.
Rotate the Gimbal
Lock to the
unlocked position.
Align the white lines
and insert the gimbal.
Rotate the Gimbal
Lock to the locked
position.
●
Be sure to remove the gimbal before transforming the aircraft to Travel Mode.
●
Always power off the aircraft before mounting or removing the gimbal.
7. Mount the
Gimbal and Camera
1 3
2
●
DO NOT use other 2.4 GHz devices at the same time to avoid signal interference.
●
DO NOT operate more than 3 aircrafts within in the same area (size equivalent to a soccer field) to prevent transmission interference.
Dual Remote Controllers
You will need to link the Master and Slave
remote controllers.
On the Master RC, launch the DJI GO
app and enter Camera View. Tap on
the top of your screen to bring up the RC
Settings. Set the RC Status as ‘Master’,
and then enter the desired connection
password.
Similarly on the Slave RC, set the RC
Status to ‘Slave’. Then tap Search for
Master RC and connect to the Master RC
with your preset password.
Connect your
mobile device with
a USB cable.
Try to keep the aircraft inside the optimal
transmission range. If the signal is weak,
adjust the antennas or fly the aircraft
closer.
Strong Weak
Unfold the mobile device holder and the antennas.
Unfold
Optimal Transmission Range
Place your mobile
device and adjust
the clamp to
secure.
Press the button to
release the clamp.
1
3
2
Charge Time:
~1 hour 18 minutes*
A
A
B
B
5. Preparing the Remote Controller
Using INSPIRE 1
●
For the best user experience, please use mobile devices with iOS 8.0 (or higher) and Android 4.1.2 (or higher).
●
Read the Inspire 1 User Manual in the DJI GO app or official DJI website for more details.
1. Download the DJI GO App
Search ‘DJI GO’ on the App Store or Google Play and
download the app to your mobile device.
Watch the tutorial videos at www.dji.com or in
the DJI GO app.
2. Watch the Tutorial Videos
The tutorial videos DJI GO app
INSPIRE 1
www.dji.com
Creativity Unleashed
©2015 DJI. All Rights Reserved
Designed by DJI. Printed in China.
www.dji.com/product/inspire-1
Learn more information from:
High
Low
Low High
3. Check Battery Levels
●
Press once to check the battery level.
●
Press once, again and hold to turn on/off.
Power Outlet
100-240V
●
The Intelligent Flight Battery must be fully charged before using it for the first time.
●
Only use the official DJI Inspire 1 charger for your Intelligent Flight Battery and remote controller. Power off the Intelligent Flight Battery before
charging.
●
When charging is complete, the LED lights on the Intelligent Flight Battery and remote controller will turn off.
Remove the battery Charge Time:
~2.5 hours*
* Provided charger
4. Charge the Batteries
●
In Dual Remote Controller Mode, only the Master remote controller can transform the landing gear.
●
DO NOT place the aircraft on rough or sound-absorbing surfaces (e.g. carpets) when transforming the landing gear.
Transform the
aircraft to Landing
Mode
Toggle the
transformation switch
up and down at least
four times
Power on the remote
controller and the aircraft
Insert the battery
6. Prepare the Aircraft
4
X