SERIES User Manual 2018.05 V1.
Searching for Keywords Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe Acrobat Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search. Navigating to a Topic View a complete list of topics in the table of contents. Click on a topic to navigate to that section. Printing this Document This document supports high resolution printing.
Contents Using this manual 2 Legends 2 Read Before the First Flight 2 Watch the Tutorial Videos 2 Download the DJI GO 4 App 2 Download the DJI Assistant 2 2 Product Profile 6 Introduction 6 Features Highlights 6 Installing the Aircraft 6 Aircraft Diagram 8 Remote Controller Diagram 8 Aircraft 13 Flight Controller 13 Flight Mode 13 Flight Status Indicator 14 Return-to-Home (RTH) 15 Intelligent Flight Mode 19 Vision System and Infrared Sensing System 27 Flight Recorder 3
DJI GO 4 App 49 Editor 52 SkyPixel 52 Me 52 Flight 54 Flight Environment Requirements 54 Flight Limits and No-Fly Zones 54 Preflight Checklist 57 Calibrating the Compass 57 Auto Takeoff and Auto Landing 58 Starting/Stopping the Motors 59 Stop the Motor Mid-flight 60 Flight Test 60 Appendix 4 49 Equipment 62 Specifications 62 Upgrading the Firmware 64 Intelligent Flight Mode 65 After-Sales Information 66 © 2018 DJI All Rights Reserved.
Product Profile This section introduces the Phantom 4 Pro / Pro+ and lists the components of the aircraft and remote controller. © 2018 DJI All Rights Reserved.
Product Profile Introduction The DJI Phantom 4 Pro / Pro+ is an extremely smart flying camera with five-directions of obstacle sensing made up of vision and infrared sensors, making it able to intelligently avoid obstacles during flight. Its brand new camera offers unprecedentedly image quality for the Phantom, with greater clarity, lower noise, higher resolution photos and videos. Dual frequency support in the remote controller makes the HD video downlink more efficient and more stable.
Phantom 4 Pro / Pro+ Series User Manual 2. Attaching the Propellers Mount the propellers with black propeller rings to the motors with black dots. Mount the propellers with sliver propeller rings to the motors without black dots. Press the propeller down onto the mounting plate and rotate in the lock direction until it is secured. Product Profile 3. Battery Installation Slide battery into the battery compartment according to the arrow’s direction as shown below.
Phantom 4 Pro / Pro+ Series User Manual Aircraft Diagram [1] [2] [3] [4] [6] [1] GPS [2] Propellers [3] Motors [4] Front LEDs [5] [5] Gimbal and Camera Product Profile [7] [8] [9] [6] Forward Vision System [7] Intelligent Flight Battery [8] Aircraft Status Indicator [9] Rear Vision System [10] Infrared Sensing System [10] [11] [13] [12] [11] Camera / Linking Status Indicator and Link Button [12] Micro USB Port [13] Camera Micro SD Card Slot [14] Downward Vision System [14] Remote Controller D
Phantom 4 Pro / Pro+ Series User Manual [5] Battery Level LEDs [8] RTH LED [6] Status LED [9] Speaker Displays the battery level of the Remote Controller. Circular LED around the RTH button displays RTH status. Displays the Remote Controller's system status. Audio output. [7] Power Button Used to turn the Remote Controller on and off. [20] [19] [21] Product Profile [18] [13] Sleep/Wake Button Press to sleep/wake the screen, press and hold to restart.
Phantom 4 Pro / Pro+ Series User Manual Phantom 4 Pro (Model: GL300F) / Phantom 4 Pro V2.0 (Model: GL300L) [3] Control Stick Controls the orientation and movement of the aircraft. [1] [2] [4] Return Home (RTH) Button Product Profile Press and hold the button to initiate Return to Home (RTH). [3] [8] [4] [7] [5] [6] [5] Battery Level LEDs Displays the battery level of the remote controller. [6] Status LED Displays the remote controller's system status.
Phantom 4 Pro / Pro+ Series User Manual [17] C1 Button Customizable through the DJI GO 4 app. [18] C2 Button [18] [17] Customizable through the DJI GO 4 app. [19] Power Port Connect to the Charger to charge the battery of the remote controller. [19] Product Profile © 2018 DJI All Rights Reserved.
Aircraft This section introduces the Flight Controller, Vision System, and the Intelligent Flight Battery. 12 © 2018 DJI All Rights Reserved.
Aircraft Flight Controller The Phantom 4 Pro / Pro+ flight controller features several important upgrades. Safety modes include Failsafe and Return-to-Home. These features ensure the safe return of your aircraft if the control signal is lost. The flight controller can also save critical flight data from each flight to the on-board storage device. The new flight controller also provides increased stability and a new air braking feature.
Phantom 4 Pro / Pro+ Series User Manual Flight Status Indicator The Phantom 4 Pro / Pro+ has Front LEDs and Aircraft Status Indicators. The positions of these LEDs are shown in the figure below: Aircraft Status Indicator Front LED Aircraft The Front LEDs show the orientation of the aircraft. The Front LEDs glow solid red when the aircraft is turned on to indicate the front (or nose) of the aircraft. The Aircraft Status Indicators communicate the system status of the flight controller.
Phantom 4 Pro / Pro+ Series User Manual Return-to-Home (RTH) Return-to-Home (RTH) function brings the aircraft back to the last recorded Home Point. There are three types of RTH: Smart RTH, Low Battery RTH, and Failsafe RTH. This section describes these three scenarios in detail. Description GPS Home Point If a strong GPS signal was acquired before takeoff, the Home Point is the location from which the aircraft launched.
Phantom 4 Pro / Pro+ Series User Manual Smart RTH Use the RTH button on the remote controller or tap the RTH button in the DJI GO 4 app and follow the onscreen instructions when GPS is available to initiate Smart RTH. The aircraft will then automatically return to the last recorded Home Point. Use the remote controller to control the aircraft’s speed or altitude to avoid a collision during the Smart RTH process.
Phantom 4 Pro / Pro+ Series User Manual Estimated remaining flight based on current battery level. Estimated remaining flight time N/A N/A N/A Precision Landing The Phantom 4 Pro / Pro+ automatically scans and attempts to match the terrain features underneath during Return to Home. When current terrain matches home point terrain, the Phantom 4 Pro / Pro+ will start landing immediately to achieve precision landing. The DJI GO 4 app will show a terrain feature mismatch prompt if matching fails.
Phantom 4 Pro / Pro+ Series User Manual Aircraft cannot return to the Home Point when GPS signal is weak ([ ] displays grey) or unavailable. If you move the left stick after the aircraft rises above 65 feet (20 meters) but below the pre-set Failsafe RTH altitude, the aircraft will stop ascending and immediately return to the Home Point.
Phantom 4 Pro / Pro+ Series User Manual • Landing Protection will not be active in the following circumstances: a) When the user is controlling the pitch/roll/throttle sticks (Landing ground detection will re-activate when control sticks are not in use) b) When the positioning system is not fully functional (e.g.
Phantom 4 Pro / Pro+ Series User Manual 3. Tap once on the target direction and wait for icon to appear. Tap again to confirm the selection and the aircraft will automatically fly towards the target direction. In Flight (GPS) 09:29 P-GPS 12 61% AE Aircraft D 30M H 10.0M H.S 10.0 M/S VS 2.0M/S VPS 2.0M DO NOT guide the aircraft to fly towards people, animals, small and fine objects (e.g. tree branches and power lines) or transparent objects (e.g. glass or water).
Phantom 4 Pro / Pro+ Series User Manual TapFly includes following functions: TapFly Forward Mode Free Mode The aircraft will fly in the opposite direction of the target. Rear Vision System is active. Aircraft The aircraft will fly towards the target. Forward Vision System is active. TapFly Backward Mode The aircraft will fly towards the target. The remote controller can be used to maneuver the yaw of the aircraft freely. Obstacle Sensing is disabled in this mode, use it in an unobstructed environment.
Phantom 4 Pro / Pro+ Series User Manual Using ActiveTrack Ensure the aircraft is in P-mode, then follow the steps below to use ActiveTrack: 1. Take off and hover at least 6 feet (2 meters) above the ground. ON 2 meters OFF Auto Hold Aircraft 2. Launch the DJI GO 4 app and tap , then tap , read and understand the prompts. In Flight (GPS) 09:29 P-GPS 12 61% AE D 30M H 10.0M H.S 10.0 M/S VS 2.0M/S VPS 2.0M 3. Tap on the subject you want to track then tap to confirm selection.
Phantom 4 Pro / Pro+ Series User Manual DO NOT select an area containing people, animals, small, fine objects (e.g. tree branches and power lines) or transparent objects (e.g. glass or water surface). Stay clear of obstacles near the flight path, particularly when the aircraft is flying backward. Be extra vigilant when using ActiveTrack in any of the following situations: a) The tracked subject is not moving on a level plane. b) The tracked subject changes shape drastically while moving.
Phantom 4 Pro / Pro+ Series User Manual Exiting ActiveTrack Use the following methods to exit ActiveTrack: 1. Tap the “STOP” button on the screen. 2. Press the Intelligent Flight Pause button on the remote controller. STOP OR After exiting ActiveTrack, the aircraft will hover in place, at which point you may choose to fly manually, track another subject, or return to home. Draw Aircraft Introduction Using Draw, the aircraft will fly along the flight path drawn on-screen.
Phantom 4 Pro / Pro+ Series User Manual In Flight（GPS） 09:29 P-GPS 12 61% Hide AE Heading 268m Forward SPEED 11.1 m/s GO Advanced Setting D 30M H 10.0M H.S 10.0 M/S VS 2.0M/S VPS 2.0M After confirming the flight path, the aircraft will fly along the path on-screen. Note: Control sticks can be used to control aircraft movement during the flight. In Flight GPS 09:29 P-GPS 12 61% AE 268m STOP D 30M H 10.0M H.S 10.0 M/S VS 2.0M/S VPS 2.
Phantom 4 Pro / Pro+ Series User Manual Gesture Mode In Gesture Mode, the Phantom 4 Pro / Pro+’s Vision System recognizes gestures, allowing it to follow and capture selfies without a phone or a controller. Follow the steps below to use Gesture Mode: Modes Prompts 1. Confirm the subject Aircraft 2. Confirm the distance 3. Selfie Count Down Front LEDs Slow Red Flashing Remarks Ensure the forward vision system is active and there is enough light.
Phantom 4 Pro / Pro+ Series User Manual It is important that you only fly in conditions where the Vision Position System can function correctly; otherwise the Terrain Follow Mode will not work. Vision System and Infrared Sensing System [1] [5] [2] [3] [4] Detection Range The detection range of the Vision System and Infrared Sensing System are depicted as follow. Note that the aircraft cannot sense and avoid the obstacles that are not within the detection range.
Phantom 4 Pro / Pro+ Series User Manual Calibrating Sensors Vision Systems cameras installed on the aircraft are calibrated on delivery. However these cameras are vulnerable to excessive impact and will require occasional calibration via DJI ASSISTANTTM 2 or the DJI GO 4 app. Follow the steps below to calibrate the camera.
Phantom 4 Pro / Pro+ Series User Manual Assisted Braking from Obstacle Sensing Powered by the Obstacle Sensing, the aircraft will now be able to actively brake when obstacles are detected around the aircraft. Note that Obstacle Sensing function works best when lighting is adequate and the obstacle is clearly marked or textured. The aircraft must fly at no more than 31mph (50kph) to allow sufficient braking distance. Aircraft The 3D Infrared Sensing System is only active in Beginner mode and Tripod Mode.
Phantom 4 Pro / Pro+ Series User Manual Flight Recorder Flight data is automatically recorded to the internal storage of the aircraft. This includes flight telemetry, aircraft status information, and other parameters. To access this data, connect the aircraft to the PC through the Micro USB port and launch the DJI Assistant 2. Attaching and Detaching the Propellers Use only DJI approved propellers with your Phantom 4 Pro / Pro+.
Phantom 4 Pro / Pro+ Series User Manual Be aware of the sharp edges of the propellers. Handle with care. Use only the DJI approved propellers. Do not mix propeller types. Check that the propellers and motors are installed correctly and firmly before every flight. Ensure that all propellers are in good condition before each flight. DO NOT use aged, chipped, or broken propellers. To avoid injury, STAND CLEAR of and DO NOT touch propellers or motors when they are spinning.
Phantom 4 Pro / Pro+ Series User Manual Refer to Phantom 4 Pro / Pro+ Intelligent Flight Battery Safety Guidelines before use. Users take full responsibility for all operations and usage. Using the Battery LED1 LED2 LED3 Aircraft LED4 Power Button (Built-in LED) Battery Level Indicators Turning ON/OFF Turning On: Press the Power Button once, then press again and hold for 2 seconds to turn on. The Power LED will turn green and the Battery Level Indicators will display the current battery level.
Phantom 4 Pro / Pro+ Series User Manual Low Temperature Notice: In cold environments, insert the battery into the battery compartment and turn on the aircraft for approximately 1-2 minutes to warm up before taking off. Charging the Intelligent Flight Battery 1. Connect the Battery Charger to a power source (100-240 V 50/60 Hz). 2. Connect the Intelligent Flight Battery to the Battery Charger to start charging. If the battery level is above 95%, turn on the battery before charging. 3.
Phantom 4 Pro / Pro+ Series User Manual Battery Protection LED Display The table below shows battery protection mechanisms and corresponding LED patterns.
Remote Controller This section describes the features of the remote controller and includes instructions for controlling the aircraft and the camera. © 2018 DJI All Rights Reserved.
Remote Controller Remote Controller Profile The Phantom 4 Pro/Pro+ series remote controller is a multi-function wireless communication device that integrates a dual frequency video downlink system and the aircraft remote control system. The remote controller features a number of camera control functions, including photo/ video capture and gimbal control. The battery level is displayed via LED indicators on the front panel of the remote controller.
Phantom 4 Pro / Pro+ Series User Manual Power Outlet Charger Controlling the Camera [4] [3] [1] [2] [1] Camera Settings Dial Turn the dial to adjust camera settings such as ISO, shutter speed, and aperture without letting go of the remote controller. Press down on the dial to toggle between these settings. [2] Shutter Button Press to take a photo. If burst mode is activated, multiple photos will be taken with a single press.
Phantom 4 Pro / Pro+ Series User Manual Controlling the Aircraft This section explains how to control the orientation of the aircraft through the remote controller. Control can be set to Mode 1 , Mode 2 or Mode 3, or to a custom mode.
Phantom 4 Pro / Pro+ Series User Manual Remote Controller (Mode 2) ( Aircraft Indicates Nose Direction) Remarks Moving the left stick up and down changes the aircraft’s elevation. Push the stick up to ascend and down to descend. When both sticks are centered, the Phantom 4 Pro / Pro+ will hover in place. The more the stick is pushed away from the center position, the faster the Phantom 4 Pro / Pro+ will change elevation. Always push the stick gently to prevent sudden and unexpected elevation changes.
Phantom 4 Pro / Pro+ Series User Manual Adjusting Controller Sticks Hold and twist the controller sticks clockwise or counter clockwise to adjust the length of the controller sticks. A proper length of controller sticks can improve the controlling accuracy. Flight Mode Switch Toggle the switch to select the desired flight mode. Choose between; P-mode, S-mode and A- mode.
Phantom 4 Pro / Pro+ Series User Manual Connecting Your Mobile Device Tilt the mobile device holder to the desired position. Press the button on the side of the mobile device holder to release the clamp, and then place your mobile device into the cradle. Adjust the clamp down to secure the mobile device. To connect your mobile device to the remote controller using a USB cable, plug one end of the cable into your mobile device and the other end into the USB port on the back of the remote controller.
Phantom 4 Pro / Pro+ Series User Manual Status LED Alarm Remote Controller Status — Solid Red Chime The remote controller is disconnected from the aircraft. — Solid Green Chime The remote controller is connected to the aircraft. Slow Blinking Red D-D-D...... Remote controller error. / Red and Green/ Red and Yellow Alternate Blinks None HD downlink is disrupted. RTH LED Sound Remote Controller Status — Solid White Chime Aircraft is returning home. Remote Controller Blinking White D...
Phantom 4 Pro / Pro+ Series User Manual 4. The remote controller is ready to link. The Remote Controller Status Indicator blinks blue and a beep is emitted. RC Control Setting RC Calibration Stick Mode Searching for aircraft frequency, Default stick mode is Mode 2, changing stick modes alters the way the aircraft is controlled. timeout in 54 seconds Do not change unless familiar with your new mode.
Camera and Gimbal This section provides the technical specifications of the camera and explains the gimbal’s operation modes. 44 © 2018 DJI All Rights Reserved.
Camera and Gimbal Camera Profile The Phantom 4 Pro / Pro+ camera uses 1-inch CMOS sensor to capture video (up to 4096×2160p at 60fps) and 20 megapixel stills. Videos can be stored in either MOV or MP4 formats. Available picture shooting modes include burst, continuous, and time-lapse mode. A live preview of what the camera sees can be monitored on the connected mobile device via the DJI GO 4 app. The Phantom 4 Pro / Pro+ supports the capture of 4K at 60fps. Both H.265 and H.
Phantom 4 Pro / Pro+ Series User Manual Camera Operation Gimbal Camera Use the Shutter and Record buttons on the remote controller to shoot the photos or videos through the DJI GO 4 app. Camera Status LED Indicator Descriptions The Camera LED Indicator lights up after the flight battery is powered on. It provides information on the working status of the camera.
Phantom 4 Pro / Pro+ Series User Manual Gimbal Profile The 3-axis gimbal provides a steady platform for the attached camera, allowing you to capture clear, stable images and video. The gimbal can tilt the camera within a 120˚ range. 30° 0° Use the gimbal dial on the remote controller to control the tilt movement of the camera. In the camera view, press and hold on the screen until a blue circle appears.
DJI GO 4 App This section introduces the four main functions of the DJI GO 4 app. 48 © 2018 DJI All Rights Reserved.
DJI GO 4 App The DJI GO 4 app is a mobile application designed specifically for DJI equipment. Use this app to control the gimbal, camera, and other aircraft functions. The app features Equipment, Editor, SkyPixel and Me sections, which are used for configuring your aircraft, editing and sharing your photos and videos with others. It is recommended that you use a tablet for the best experience.
Phantom 4 Pro / Pro+ Series User Manual 1. System Status : This icon indicates aircraft flight status and various warning messages. READY TO GO (GPS) 2. Obstacles Detection Status : Red bars are displayed when obstacles are close to the aircraft. Orange bars are displayed when obstacles are in detection range. 3. Battery Level Indicator : The battery level indicator provides a dynamic display of the battery level.
Phantom 4 Pro / Pro+ Series User Manual 13. Auto Exposure Lock AE : Tap to lock the exposure value. 14. Photo/Video Button : Tap to switch between photo and video recording modes. 15. Gimbal Slider : Displays the pitch of the gimbal. 16. Shoot / Record Button / : Tap to start shooting photos or recording video. 17. Camera Settings : Tap to set ISO, shutter and auto exposure values of the camera. 19. Map Tap the Mini Map to switch between Camera View and Map View. 20. Flight Telemetry D 30M H 10.
Phantom 4 Pro / Pro+ Series User Manual 21. Intelligent Flight Mode : Display the current mode. Tap to select Intelligent Flight Mode. 22. Smart RTH : Initiate RTH home procedure. Tap to have the aircraft return to the last recorded home point. 23. Auto Takeoff/Landing / : Tap to initiate auto takeoff or landing. 24. Livestream : This icon indicates the current video feed is being broadcast live on YouTube. Ensure that mobile data service is available on your mobile device. 25.
Flight This section describes safe flight practices and flight restrictions. © 2018 DJI All Rights Reserved.
Flight Once pre-flight preparation is complete, it is recommended that you use the flight simulator in the DJI GO 4 app to hone your flight skills and practice flying safely. Ensure that all flights are carried out in an open area. Flight Environment Requirements Flight 1. Do not use the aircraft in severe weather conditions. These include wind speeds exceeding 10 m/s , snow, rain and fog. 2. Only fly in open areas.
Phantom 4 Pro / Pro+ Series User Manual GPS Signal Strong Blinking Green Flight Limits DJI GO 4 App Aircraft Status Indicator Maximum Flight Altitude Aircraft's altitude cannot exceed the specified value. Warning: Height limit reached. None. Max Radius Flight distance must be within the max radius. Warning: Distance limit reached. Rapid red flashing when close to the max radius limit.
Phantom 4 Pro / Pro+ Series User Manual 1640 feet 66 feet 1 mile R1 R2 320 feet 1640 feet 66 feet 1 mile 320 feet R1 R2 Restricted Area Flight (1) Restricted Areas does not have flight altitude restrictions. (2) R miles around the designated restriction area is a Take-off Restricted area. Aircraft cannot take off within this zone. The value of R varies based on the definition of the restricted areas. (3) A “warning zone” has been set around the Restricted Area. When the aircraft approaches within 0.
Phantom 4 Pro / Pro+ Series User Manual Preflight Checklist 1. 2. 3. 4. 5. 6. 7. Remote controller, Intelligent Flight Battery, and mobile device are fully charged. Propellers are mounted correctly and firmly. Micro SD card has been inserted, if necessary. Gimbal is functioning normally. Motors can start and are functioning normally. The DJI GO 4 app is successfully connected to the aircraft. Ensure that the sensors for the Obstacle Sensing System are clean.
Phantom 4 Pro / Pro+ Series User Manual 3. Hold the aircraft vertically, with nose pointing downward, and rotate it 360 degrees around the center axis. Flight 4. Re-calibrate the aircraft if the aircraft status indicators glows blinking red. If the Aircraft Status Indicator blinks red and yellow after the calibration procedure, move your aircraft to a different location and try again. DO NOT calibrate the compass near metal objects such as a metal bridge, cars, scaffolding.
Phantom 4 Pro / Pro+ Series User Manual 2. Abort landing process immediately by using the button on the screen. 3. a. When Landing Protection determines that the ground is suitable for landing, the Phantom 4 Pro / Pro+ will land gently. b. If Landing Protection determines that the ground is not suitable for landing, the Phantom 4 Pro / Pro+ will hover and wait for pilot confirmation. c.
Phantom 4 Pro / Pro+ Series User Manual Stop the Motor Mid-flight Pull the left stick to the bottom inside corners and press the RTH button at the same time. Only stop the motors mid-flight in emergency situations when doing so can reduce the risk of damage or injury. Flight Flight Test Takeoff/Landing Procedures 1. 2. 3. 4. 5. 6. 7. 8. 9. Place the aircraft in an open, flat area with the battery level indicators facing towards you.
Appendix © 2018 DJI All Rights Reserved.
Appendix Specifications Aircraft Weight (Battery & Propellers Included) Phantom 4 Pro/Pro+: 1388 g Phantom 4 Pro/Pro+ V2.0: 1375 g Appendix Diagonal Size (Excluding Propellers) 350 mm Max Ascent Speed Sport mode: 19.7ft/s(6 m/s); GPS mode: 16.4ft/s(5 m/s) Max Descent Speed Sport mode: 13.1ft/s(4 m/s); GPS mode: 9.
Phantom 4 Pro / Pro+ Series User Manual Infrared Sensing System Obstacle Sensory Range 0.6 - 23 ft (0.2 - 7 m) FOV 70°(Horizontal), ±10°(Vertical) Measuring Frequency 10 Hz Operating Environment Surface with diffuse reflection material, and reflectivity > 8% (such as wall, trees, humans, etc.) Camera 1’’ CMOS; Effective pixels: 20 M Lens FOV (Field of View) 84°, 8.8 mm (35 mm format equivalent: 24 mm), f/2.
Phantom 4 Pro / Pro+ Series User Manual Max. Bitrate Of Video 100 Mbps Supported File Systems FAT32 (≤ 32 GB); exFAT (> 32 GB) Photo JPEG, DNG (RAW), JPEG + DNG Video MP4/MOV (AVC/H.264; HEVC/H.265) Supported SD Cards Micro SD, Max Capacity: 128GB. Write speed ≥15MB/s, class 10 or UHS-1 rating required Operating Temperature Range 32° to 104° F (0° to 40° C) Remote Controller Operating Frequency Phantom 4 Pro / Pro+: 2.400 - 2.483 GHz and 5.725 - 5.825 GHz Phantom 4 Pro / Pro+ V2.0: 2.400 - 2.
Phantom 4 Pro / Pro+ Series User Manual Upgrading the Firmware Use the DJI GO 4 app or DJI Assistant 2 to update the firmware of the aircraft and remote controller. Phantom 4 Pro/Pro+ Phantom 4 Pro/Pro+ does not support updating the aircraft and the remote controller simultaneously. Please follow the update process below. Updating the Aircraft Firmware Method 1: Using DJI GO 4 1. Ensure both the aircraft and the remote controller are powered on and connected. 2.
Phantom 4 Pro / Pro+ Series User Manual Method 1: Using DJI GO 4 Connect the remote controller and DJI GO 4, where you will be reminded if a new firmware update is available. To start updating, connect your mobile device to the internet and follow the on-screen instructions. Method 2: Using DJI Assistant 2 When the aircraft and the remote controller are connected, you can update both of them simultaneously with DJI Assistant 2 (only for Phantom 4 Pro V2.0, where separate updating is also supported).
Phantom 4 Pro / Pro+ Series User Manual Follow Me A virtual tether is created between the aircraft and the mobile device so that the aircraft can track your movement as you move. Note that Follow Me performance is subject to the GPS accuracy on the mobile device. Record a flight path, then the aircraft will fly along the same path repeatedly while Waypoints you control the camera and orientation. The flight path can be saved and re-apply in the future.
DJI Support http://www.dji.com/support This content is subject to change. Download the latest version from http://www.dji.com/product/phantom-4-pro If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. PHANTOM is a trademark of DJI. Copyright © 2018 DJI All Rights Reserved.
V2.0 Quick Start Guide V1.
Phantom 4 Pro V2.0 The DJI PHANTOMTM 4 Pro V2.0 is a smart prosumer flying camera capable of shooting 4K video at 60 fps and at up to 100 Mbps, and capturing 20 megapixel stills. 4 directions of obstacle avoidance allow it to intelligently avoid obstacles during flight. Using TapFlyTM and ActiveTrackTM through the DJI GOTM 4 app, you can fly anywhere visible on your screen or track a moving subject smoothly and easily with a simple tap.
Remote Controller The powerful remote controller of the Phantom 4 Pro V2.0 has a transmission range extending up to 4.3 mi (7 km)*. It features physical buttons and dials to control exposure, camera tilt, photo capture, and video recording. Built into the remote controller is DJI's latest long-range transmission technology OCUSYNCTM, which when paired with a compatible mobile device gives you a live HD view from the Phantom’s camera. Dual frequency support makes the HD video downlink more stable. 11.
Using Phantom 4 Pro V2.0 1. Download the DJI GO 4 App 2. Watch the Tutorial Videos Watch the tutorial videos at www.dji.com or in the DJI GO 4 app. Search for ‘DJI GO 4’ on the App Store or Google Play, and install the app on your mobile device. Tutorial Videos DJI GO 4 App ● DJI GO 4 supports iOS 9.0 (or later) or Android 4.4 (or later). 3. Check the Battery Levels Low Battery Level Low High Battery Level Press once to check the battery level. Press once, then again and hold to turn on/off.
5. Prepare the Remote Controller 2 Press the button to release the clamp. Unfold Strong Place your mobile device and adjust the clamp to secure. 1 Connect your mobile device with a USB cable. 3 Weak 6. Prepare for Takeoff DJI GO 4 App Remove the gimbal clamp from the camera. Launch DJI GO 4, complete the first-time setup, and tap GO FLY. Power on the remote controller and the aircraft. First-time activation requires your DJI account and internet connection.
7. Flight Ready to Go (GPS) Before taking off, make sure the Aircraft Status Bar in the DJI GO 4 app indicates ‘Ready to Go (GPS)’ or ‘Ready to Go (Vision)’ if flying indoors. In the DJI GO 4 App: Auto Takeoff Auto Landing The aircraft will take off and hover at an altitude of 4 feet (1.2 meters). The aircraft will land vertically and stop its motors. Return-to-Home (RTH) Normal Bring the aircraft back to the Home Point. Tap again to stop the procedure.
Specifications ● Max Service Ceiling Above Sea Level Max Flight Time Operating Temperature GNSS Operating Frequency Transmitter Power (EIRP) Hover Accuracy Range Gimbal Controllable Range Vision System Velocity Range Altitude Range Operating Range Obstacle Sensory Range Operating Environment ● Infrared Sensing System Obstacle Sensory Range Operating Environment ● Camera Sensor Lens ISO Range Mechanical Shutter Electronic Shutter Max Image Size Still Photography Modes 1375 g S-mode: 6 m/s; P-mode: 5 m/s S-
V2.0 www.dji.
V2.0 In the Box Check that all of the following items are in your package. If any item is missing, please contact DJI or your local dealer. Essentials Aircraft Body ×1 Remote Controller ×1 Propeller Pairs ×4 Intelligent Flight Battery ×1 Battery count varies with different bundles.
Phantom 4 Pro/Pro+ V2.0 Release Notes Date: 2018.06.26 Aircraft Firmware: V 01.00.15.00 Phantom 4 Pro V2.0 Remote Controller Firmware: V 01.00.15.00 Phantom 4 Pro+ V2.0 Remote Controller Firmware: V 01.00.01.00 DJI GO 4 App iOS: V 4.2.20 DJI GO 4 App Android: V 4.2.20 What’s New? Optimized compass calibration. Optimized gimbal performance to improve its stability during flight. Notes: Once the firmware has been updated, it cannot be reverted to a previous version.
DISCLAIMER AND SAFETY GUIDELINES V1.2 2017.
Contents Safety At a Glance 2 NOTICE 4 Glossary 4 Pre-flight Checklist 4 Disclaimer and Warning 5 Before You Begin 7 Individual Parts 7 Regarding Genuine and Functional Parts 7 Remote Controller 7 Camera 8 Gimbal 8 Compass 8 Propulsion Systems 9 DJI GO 4 App 9 Firmware 10 Product Care 10 Storage and Transportation 10 Maintenance and Upkeep 11 Flight Condition Requirements 11 Weather Conditions and Surrounding Environment 11 Interference with Communications 11 Operat
Safety At a Glance 1. Environmental Consideration Always fly at locations that are clear of building and other obstacles. DO NOT fly above or near large crowds. Avoid flying at altitudes above 400 feet (120 m).* Be very careful when flying 19,600 feet (6,000 m) or more above sea level. • Fly in moderate weather conditions with temperatures between 32° to 104° F (0° to 40° C). • Please take additional caution while flying indoors because the aircraft stabilization features may be interfered.
4. Maintenance and Upkeep • DO NOT use aged, chipped or broken propellers. • Recommended storage temperature: between 71° and 82° F (22° and 28° C). • Refer to the Phantom 4 Series Intelligent Flight Battery Safety Guidelines for more information about the safe use of the battery. 5. Observe Local Laws and Regulations • DO NOT fly in the No Fly Zones. You can find a complete list of these areas at http://flysafe.dji.
NOTICE All instructions and other collateral documents are subject to change at the sole discretion of SZ DJI TECHNOLOGY CO., LTD. For up-to-date product information, visit http://www.dji.com and click on the product page.
Disclaimer and Warning This product is NOT a toy and is not suitable for children under the age of 18. Adults should keep the aircraft out of the reach of children and exercise caution when operating this aircraft in the presence of children. While the product adopts advanced technology, inappropriate use of the Product could result in personal injury or property damages. Please read the materials associated with the product before your first use of the product.
The information that is automatically uploaded or manually uploaded to us include personal data, such as your user name, may become associated with, used to identify, or tagged to such uploaded information when we store it. We separately describe how we use your user name and other personal data on our privacy policy at http://www.dji.com/ policy.
Before You Begin The following documents have been produced to help you safely operate and make full use of your aircraft: In the Box Disclaimer and Safety Guidelines Intelligent Flight Battery Safety Guidelines Quick Start Guide User Manual Check all of the included parts listed in the In the Box document and read the Disclaimer and Safety Guidelines before flight.
Camera To avoid possible serious injury and property damage, observe the following rule: 1. DO NOT block any ventilation holes on the camera as the heat generated may hurt you and damage the device. 1. Check camera settings before use to make sure you can adjust them to fit your needs. 2. Test the camera by shooting a few test images and check that it is operating correctly before shooting important pictures or videos. 3. DO NOT remove the Micro SD card from the camera when it is powered on. 4.
Propulsion Systems To avoid serious injury to yourself or others, which may be caused by the rotating propellers and motors, observe the following rules: Propellers 1. DO NOT use aged, chipped, or broken propellers. 2. Always power off the aircraft before touching the propellers. 3. Be aware of the sharp edges of the propellers when mounting or removing the propellers. Wear gloves or take other protective measures when touching the propellers. 4. Whenever necessary, use tools (e.g.
5. Land your aircraft immediately if there is an alert shown on the app. 6. Examine and check all warning messages on the checklist displayed in the app prior to each flight. 7. Use the in-app simulator to practice your flight skills if you have never operated the aircraft or if you do not have sufficient experience to be comfortable operating the aircraft. 8. Beginner Mode is enabled by default when you launch the app for the first time.
wet, wipe dry with a soft, absorbent cloth. Turning on an aircraft that has fallen into water may cause permanent component damage. DO NOT use substances containing alcohol, benzene, thinners or other flammable substances to clean or maintain the camera. DO NOT store the camera in humid or dusty areas. 3. DO NOT connect this product to any USB interface that is older than version 2.0. DO NOT connect this product to any "power USB" or similar devices. Maintenance and Upkeep 1.
Operating the Aircraft Responsibly To avoid serious injury and property damage, observe the following rules: 1. Make sure you are NOT drunk, taking drugs, under the influence of anesthesia, or suffering from dizziness, fatigue, nausea or any other conditions, whether physical or mental, that could impair your ability to operate the aircraft safely. 2. Pulling the left stick to the bottom inside corners and pressing the RTH button at the same time will stop the motor when the aircraft is airborne.
P-mode or S-mode is preferred for most flight scenarios. Users can switch to A-mode if P-mode or S-mode is unavailable. When flying in A-mode, take EXTRA precautions because some features are NOT available in A-mode. 1. P-mode (Positioning): P-mode works best when the GPS signal is strong. The aircraft utilizes the GPS and Vision System to automatically stabilize itself, navigate between obstacles or track a moving object. Advanced features such as TapFly and ActiveTrack are enabled in this mode. 2.
Vision System and Infrared Sensing System* 1. The Vision System cannot work properly over surfaces that do NOT have clear pattern variations. The Vision System is only effective when the aircraft is at altitudes of 0.3 to 10 meters. 2. The Vision System may NOT function properly when the aircraft is flying over water or snow-covered areas. 3. Keep your pets away from the aircraft when the Vision System is activated, as the sonar sensors emit a high frequency sound that is only audible to some pets. 4.
0.7m 13.1cm Phantom 4 Advanced / Phantom 4 Advanced+ Phantom 4 Series TapFly To prevent serious injury or property damage, observe the following guidelines: 1. DO NOT instruct the aircraft to fly towards people, animals, small and fine objects (e.g. tree branches and power lines) or transparent objects (e.g. glass and water). 2. Watch out for potential obstacles in your surrounding area (especially on the rear, left, and right sides of the aircraft) and stay clear of them to avoid accidents. 3.
b. The tracked subject changes shape drastically while moving; c. The tracked subject could be blocked or out of sight for a long time; d. When the tracked object is in a snow-covered area; e. The lighting is extremely low (< 300 lux) or high (> 10,000 lux); and f . The tracked subject has a similar color or pattern as the surrounding environment. 2. You must follow local privacy laws and regulations when using ActiveTrack.
No Fly Zones 1. No Fly Zones include but are not limited to major airports around world, borders between two sovereign countries or regions, major cities/regions, etc. 2. The complete list of No Fly Zones is listed on the official DJI website at http://flysafe.dji.com/no-fly and is subject to periodic updates in line with the latest regulatory requirements without prior notice. 3. Some No Fly Zones are comprised of several zones. Each zone features circles of various sizes.
must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. KCC Warning Message “해당무선설비는 운용 중 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다 .
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS Environmentally friendly disposal Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points.
This content is subject to change. Download the latest version from www.dji.com If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. PHANTOM is a trademark of DJI. Copyright © 2017 DJI All Rights Reserved. YC.BZ.S01189.04 Printed in China.
PHANTOM 4 SERIES INTELLIGENT FLIGHT BATTERY Safety Guidelines V1.0 2016.
NOTICE All instructions and other collateral documents are subject to change at the sole discretion of SZ DJI TECHNOLOGY CO., LTD. For up-to-date product information, visit http://www.dji.com and click on the product page for this product.
6. DO NOT use the battery in strong electrostatic or electromagnetic environments. Otherwise, the battery control board may malfunction and cause a serious accident during flight. 7. Never disassemble or pierce the battery in any way or the battery may leak, catch fire, or explode. 8. Electrolytes in the battery are highly corrosive. If any electrolytes make contact with your skin or eyes, immediately wash the affected area with fresh running water for at least 15 minutes, and then see a doctor immediately.
Travel Notice 1. Before carrying the Intelligent Flight Battery on an airline flight, it must first be fully discharged. This can be done by using your aircraft until the battery is depleted. Only discharge the battery in a fireproof location. Battery Use 1. Make sure the batteries are fully charged before each flight. 2. Land the aircraft immediately when the low battery level warning activates in the DJI GO app. Battery Charging 1.
DJI/Customer service 1 (818) 235-0789 https://www.dji.
Additional charges may apply outside DJI’s normal service areas. Please contact DJI for information specific to your location What to do Before Obtaining After-sales Service Before obtaining after-sales service, the following steps must be taken: √ Follow the procedures specified by DJI. √ Backup all data contained on your product’s SD card. √ Except for flight logs, remove all data, including confidential information, proprietary information and personal information, from the product.
If you obtain service under this policy, you authorize DJI to store, use, and process your flight log information and your contact information, including name, phone numbers, address, and email address. DJI may use this information to perform service under this policy. We may contact you to inquire about your satisfaction with our service or to notify you about any product recalls or safety issues.
When receiving service, DJI is responsible for loss or damage to your product only while it is in DJI's possession or in transit, if DJI is responsible for transportation. DJI is NOT responsible for loss or disclosure of any data, including confidential information, proprietary information, or personal information, contained in a product.
