PHANTOM 2 VISION User Manual V1.2 June 2014 Revision Congratulations on purchasing your new DJI product. Please thoroughly read the entire contents of this manual to fully use and understand the product. It is advised that you regularly check the PHANTOM 2 VISION’s product page at www.dji.com which is updated on a regular basis. This will provide services such as product information, technical updates and manual corrections.
Index IN THE BOX .....................................................................................................................4 REQUIRED ITEMS ............................................................................................................4 SYMBOL LEGEND ............................................................................................................5 WATCH THE QUICK START VIDEOS ..................................................................................
8.2 BUILT-IN FLIGHT CONTROL SYSTEM INSTRUCTIONS................................................................26 8.3 LED FLIGHT INDICATORS DESCRIPTION ...............................................................................26 9 CONNECTING TO THE CAMERA .................................................................................. 28 9.1 CAMERA CONNECTION PROCEDURES..................................................................................28 10 CALIBRATING THE COMPASS .....................
In the Box PHANTOM 2 VISION X1 5.8GHz Remote Controller X1 Range Extender X1 Propeller Pair X4 Mobile Device Holder X1 Micro-SD Card X1 Intelligent Battery X1 Charger X1 Cables X1 Plug Set X1 Screw X12 Screwdriver X 1 Assistant Wrench X1 Accessories Box X1 Required Items AA Battery x4 ©2014 DJI. All Rights Reserved.
Symbol Legend Forbidden(Important) Caution Tip Reference Watch the Quick Start Videos This user manual details installation and usage procedures of the product. In addition, we provide a range of quick start videos. It is advised that you watch them fully before attempting to use the product. Approach 1 Direct link. www.dji.com/phantom-2-vision/training Preparing for flight. Approach 2 Scan the QR code to get the How to connect to the DJI VISION App. quick start video link.
1 Attaching the Propellers Please use the original 9-inch propellers which are classified by the color of each central nut. Damaged propellers can be replaced by purchasing new ones if necessary. 1.1 Introduction Propellers Grey Nut (9443) Black Nut (9443 R) Attach to the motor thread that does Attach to the motor thread that has a not have a black dot. black dot. Diagram Assembly Location Fastening/Un-fastening Lock: Tighten the propeller in this direction.
2 Installing the Range Extender and Mobile Device Holder 2.1 Installing the Range Extender 1. Adjust the range extender to align with the mounting bracket installed on the carrying handle. 2. Tighten the lock-screw to affix the range extender on the right side of the carrying handle. (1) Make sure the assembly orientation is correct with the LED side facing you. (2) To obtain better communication, try to keep the range extender facing the aircraft during flight. Lock Screw 2.
3 Preparing the Remote Controller The PHANTOM 2 VISION remote control is a wireless communication device that uses the 5.8GHz frequency band. It is compliant with CE and FCC (see the FCC ID) regulations and is set to Mode 2 before delivery. The compliance version can be configured by twisting the potentiometer knob on the back of the remote controller. The stick configuration can also be reset in the PHANTOM RC Assistant Software.
(1) If the low voltage warning alert sounds (refer to the ), please replace batteries as soon as possible. (2) Using the incorrect type of battery may prevent a risk of damage. (3) Remove the batteries after use and dispose of them safely. (4) For long term storage, be sure to remove the batteries from the remote controller. 3.
OFF CAM ON WIFI ON MICRO SD The remote controller’s antenna should be pointing skyward with no obstacles in the way. Otherwise, the Failsafe function may initialize prematurely during flight. The Mobile Device and Range Extender should not block the antenna. 3.5 Remote Controller Operation Definitions The ‘stick neutral’ positions and ‘stick released’ mean the control sticks of the remote controller are placed at the central position.
command stick results in faster aircraft rotation velocity. The pitch stick controls the aircraft’s front & back tilt. Push the stick up and the aircraft will tilt and fly forward. Pull the stick down and the aircraft will tilt and fly backward. The aircraft will keep level and straight if the stick is centered. Increasing movement of the command stick will result in a larger tilt angle (maximum is 35˚) and faster flight velocity. The roll stick controls the aircraft left & right tilt.
接收机对频按键 Link Button &对频指示灯 & Link Indicator Link Procedures 1. Power off the remote controller, power on the aircraft. You will see the link indicator blinking red. 2. Press the link button with a thin object and hold until the link indicator blinks yellow. Release the link button. 3. Power on the remote controller and the link indicator should switch off. This indicates that the link has been successfully established. Link Indicator Link Indicator Description Operation No signal received.
When adjusting the potentiometer knob to its limit position, be very careful to prevent damaging the potentiometer knob. Do not apply too much force during this adjustment. Also be sure to use the correct sized screwdriver. (1) It is recommended to use a flathead screwdriver of Φ 2.4mm for adjustment. (2) You can use the DJI screwdriver with the flathead for adjustment. (3) There is another potentiometer reserved. ©2014 DJI. All Rights Reserved.
4 Preparing the Range Extender The PHANTOM 2 VISION range extender is a wireless communication device that operates within the 2.4 GHz frequency band and is used for extending the effective range of communication between a mobile device (Smartphone) and the PHANTOM 2 VISION. In an open unobstructed area, the transmission distance can reach up to 300 meters, but is usually affected by the surrounding environment, such as trees, buildings and other sources of the same frequency.
(1) Make sure to charge the range extender completely before using it for the first time. (2) If the power indicator is a solid red light, the ranger extender may stop working at any moment. Recharge it as soon as possible. (3) It is recommended to charge the range extender completely before each use. (4) Turn off the range extender after every use. (5) Keep the range extender facing the aircraft during flight for the best communication link.
Reset Button 1. Power on the camera and range extender. Note:(Place the camera power switch to the ’WIFI ON‘ position). 2. Approximately 30 seconds later, press the reset button on the range extender with a thin object until the Wi-Fi signal indicator turns off. The range extender will then restart automatically. 3. Approximately 30 seconds later, the Wi-Fi signal indicator should start to blink green, which indicates the range extender is now ready to be bound. 4.
Fig.3 (1) If both the camera and range extender are powered on and working normally, you will be able to find the SSID on the Wi-Fi list of the mobile device. (2) DO NOT push the reset button of the range extender unless you are ready to rebind the range extender and the camera! This will unbind your camera and you must follow the steps above to rebind. (3) The QR code is located on the packaging of the PHANTOM 2 VISION.
5 Preparing the Camera 5.1 The built-in camera [1] [2] [1] Lens [2] Camera Power Switch [3] Micro-SD Card Slot [4] Camera Status Indicator [5] Camera Cable [6] Capture/Record Button [4] OFF CAM ON WIFI ON [3] [6] [5] MICRO SD Camera Features Specifications Resolution 14 Megapixels FOV 120°/ 110° / 85° Sensor size 1/2.3” Supports multi-capture, continuous capture and timed capture Functions Supports HD Recording (1080p30/1080i60) Supports both RAW and JPEG photo formats 5.
[3] Micro-SD Card Slot (on the back of the camera) Make sure that the Micro-SD card is inserted before you take any photos or record any videos. (1) Maximum supported Micro-SD card capacity is 32GB. (2) The DJI VISION App may not be able to read the Micro-SD card prepared by the user. It is suggested that you use the DJI VISION App to format the Micro-SD card when first used in the camera. (3) Refer to the for Micro-SD card formatting details.
(0.5s green, 0.5s yellow, 0.5s red, 0.5s Off) ON/OFF Camera has overheated When camera temperature rises above 80℃, the LED indicator will blink . The camera will automatically power off if the temperature rises above 85℃. [5] Camera Cable (on the back of the camera) Make sure that the camera cable is firmly attached to the camera before powering the camera on.
6 Downloading and Installing the DJI VISION App 6.1 Download and Install Download and install approaches Scan the QR code to read the download link. Download and install the DJI VISION App on your Approach 1 mobile device. You can find the QR code on the ‘Quick Start Guide’ as well as on the packaging of the PHANTOM 2 VISION. Approach 2 iOS user Search “DJI VISION” from App Store, download and install on your mobile device.
[1] Register Select ‘Register’ to enter the registration page. Fill in your Email and Password information and then select to create a new account. [2] Login Select ‘Login’ to enter the login page. Fill in your registered Email and Password and then select to login. (1) You should login to your account the first time you use the DJI VISION App. (2) If you do have an account, but forgot the password, select the “Forgot password” to retrieve it.
7 Preparing the Flight Battery Before use, please read and follow the user manual, disclaimer, and the warnings on the battery. Users take full responsibility for all operations and usage. 7.1 Intelligent Battery and Charger Instructions The intelligent battery is specially designed for the PHANTOM 2 VISION, with a battery capacity of 5200mAh, voltage of 11.1v and charge-discharge management functionality. The battery should only be charged with the charger provided by DJI.
7.3 Install the Battery Push the battery into the battery compartment correctly as the following diagram shows. Make sure to push the battery into the compartment until you hear a ‘click’ sound. An incorrectly inserted battery may cause one of the following to occur: (1) Bad contact. (2) Unavailable battery information. (3) Unsafe for flight. (4) Unable to take off. 7.
Battery level indicator Current battery level LED1 LED2 LED3 LED4 On On On On 87.5%~100% On On On Blinking 75%~87.5% On On On Off 62.5%~75% On On Blinking Off 50%~62.5% On On Off Off 37.5%~50% On Blinking Off Off 25%~37.5% On Off Off Off 12.5%~25% Blinking Off Off Off 0%~12.5% Off Off Off Off <0% 7.5 Correct Battery Usage Notes It’s suggested you purchase a new battery after you have discharged your current battery over 300 times.
8 PHANTOM 2 Aircraft 8.1 The Aircraft [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [11] OFF CAM ON WIFI ON MICRO SD [1] Propeller [2] Motor [3] Front Side [4] Front LEDs [5] Micro-USB [6] Vibration Absorber [7] Compass [8] LED Flight Indicators [9] DJI Intelligent Battery [10] Servo [11] Receiver Antenna [12] Landing Gear 8.
LED Flight Indicators Description Normal status LED flight indicators Notes Power On Self-Test ---- Warming Up Aircraft cannot take off. Ready to Fly Slow blinking green. Ready to Fly (non-GPS) Slow blinking yellow. Abnormal status LED flight indicators Remote Controller Signal Lost st 1 2 nd Level Low Battery Capacity Warning Level Low Battery Capacity Warning Not Stationary or Sensor Bias is too big Fast blinking yellow. Refer to . Slow blinking red.
9 Connecting to the Camera 9.1 Camera Connection Procedures Please carry out the following procedures to connect a mobile device to the PHANTOM 2 VISION. 1. Power on the remote controller and the range extender. 2. Make sure the switch on the back of the camera is set to “WIFI ON” and then power on the PHANTOM 2 VISION. 3. (Fig.1)Enable the Wi-Fi on your mobile device; wait for about 30 seconds, and then select the Phantom_xxxxxx from theWi-Fi network list. 4. (Fig.
Wi-Fi Connection Indicator Description Description Icon Solid green Wi-Fi is now connected to the PHANTOM 2 VISION. Solid blue Wi-Fi is connected to another Wi-Fi network and NOT to the PHANTOM 2 VISION. Off No Wi-Fi connection. (1) The first time you launch the DJI VISION App, Internet access is required to finish the login process or new account creation. (2) The SSID is unique for each PHANTOM 2 VISION which should appear in your Wi-Fi list as Phantom_xxxxxx.
10 Calibrating the Compass IMPORTANT: Make sure to perform the Compass Calibration procedures prior to the first flight. The compass is very sensitive to electromagnetic interference which causes abnormal compass data and leads to poor flight performance or even flight failure. Regular calibration of the compass enables the compass to perform at its optimal level. 10.
11 Flight 11.1 Flying Environment Requirements (1) Before your first flight, please allow yourself some flight training (Using a flight simulator to practice flying, getting instruction from an experienced person, etc.). (2) DO NOT fly in bad weather, such as rain or wind (more than moderate breeze) or fog. (3) The flying field should be open and void of tall buildings or other obstacles; the steel structure within buildings may interfere with the compass.
command to start motors. 8. Push the throttle stick up slowly to lift the aircraft off the ground. Refer to for more details. 9. Enjoy your flight while capturing and recording with the DJI VISION App. Refer to the for more details. 10. Be sure you are hovering over a level surface. Pull down on the throttle stick gently to descend and land. 11.
Home Point When the aircraft is initializing the Ready to Fly status, the aircraft will record the current GPS coordinates as the home point. It is recommended to lift off only after Ready to Fly status is confirmed for the safety of being able to fly back to home point successfully in case the Failsafe mode is initiated. Go Home Procedures 1 2 Flying. Record Home Point. 3 Remote controller signal lost.
Failsafe on the DJI VISION App The DJI VISION App will provide information during Failsafe. Control Signal Lost Indicator Going Home Indicator Refer to the for details. 11.5 Low Battery Capacity Warning Function The low battery capacity warning alerts users when the battery is close to depletion during flight. When it appears, users should promptly fly back and land to avoid accidental damage. The PHANTOM 2 VISION has two levels of low battery capacity warning.
Low Battery Capacity Warning Refer to the for details. (1) Remember to fly your PHANTOM 2 VISION back as soon as you see a low battery capacity warning. (2) The PHANTOM 2 VISION is "Ready To Fly," "Ready to Capture" and "Ready to Share" but it is still an aircraft. Keeping the battery contact needles and pads clean is very important. Any dirt and dust may cause a communication failure. 11.
Max Height Max Radius Home Point The height of aircraft when it is powered on Ready to Fly Rear LED flight indicator Limits Max Height Max Radius The flight height is restricted to fly under the max None. height. The flight distance is restricted to fly within the max Rapid red flashings radius. close to the Max radius limit.
Category A Safety Zone The category A “safety zone” is comprised of a small “no-fly zone” and a range of “restricted-altitude zones”. Flight is prevented in the “no-fly zone” but can continue with height restrictions in the restricted-altitude zone. 1.5 miles (2.4 km) around a designated safety zone is a no-fly zone, inside which takeoff is prevented. 1.5 miles (2.4 km) to 5 miles (8 km) around restricted areas are altitude restricted, with maximum altitude going from 35 feet (10.5 m) at 1.
Ready to Fly mode Zone Restriction Motors will not start. Rear LED Flight DJI VISION App Notification Indicator Warning: You are in a No-fly zone. Take off prohibited. If the Phantom enters the No-fly Zone restricted area in Ready to Fly (non-GPS) mode but Ready to Warning: You are in a No-fly zone, Fly mode activates, the Phantom automatic landing has begun. (If you will automatically descend to are within 1.5 mile radius) land then stop its motors after landing.
switch to regain control. This is the same as regaining control during Failsafe. Please refer to Regaining Control During Failsafe Procedure. (1) When flying in the safety zone, LED flight indicators will blink red quickly and continue for 3 seconds, then switch to indicate current flying status and continue for 5 seconds at which point it will switch back to red blinking.
12 Using DJI VISION App The DJI VISION App controls the PHANTOM 2 VISION camera including capture and recording, settings, pitch angle adjustments, and displays essential status including flight parameters and battery life. 12.1 DJI VISION App Main Menu After login you will come to the main page. This shows the current Wi-Fi connection and four app function icons.
[1] Return - Return to the preview page [2] Camera Tilt Control - Tilt Control Mode. Tap and hold to enter the Accelerometer Sensor Mode. Release to return to normal mode. Normal Mode Tap up arrow ( ) to pitch camera upwards and down arrow ( ) to pitch downwards. Green slider indicates current camera pitch. Normal Mode pitch control Pitch movement Accelerometer Sensor Mode Tap and Hold to switch on Accelerometer Sensor Mode to control camera pitch and rotation by moving your mobile device.
[3] Flight Attitude and Radar Function Flight attitude is indicated by the flight attitude icon. (1) The red arrow shows which direction the PHANTOM 2 VISION is facing. (2) Blue and brown areas indicate its pitch. (3) Tilting of the brown and blue area shows roll angle. Tap the flight attitude icon to turn on the radar function. Home is located in the center of the radar and the red icon indicates the PHANTOM 2 VISION’s current heading, direction, and approximate distance from home.
[6] Aircraft Battery Level (1) When available power is more than 30%, the battery icon is blue (e.g. ). This battery level is appropriate for flight. (2) When below 30%, the battery icon will turn red (e.g. ) and the LED flight indicator will slowly blink red. This battery level is low for flight. It is recommended that you fly your PHANTOM 2 VISION home and land it as soon as possible. (3) After available power drops below 15% (e.g. ), there is no longer enough power for flight.
[11] Record Button Start and Stop video recording. Tap once to start recording. A red dot will blink to indicate recording is in progress and a time elapsed counter will appear in the top right corner of the preview screen. Press again to stop recording. [12] Camera Settings Tap to open the camera settings menu, refer to . [13] Hide or Show Flight Parameters. Tap to hide the flight parameters. Tap again to show.
[2] Photo Size Large: 4384 x 3288, 4:3, 14.4MP Medium: 4384 x 2922, 3:2, 12.8MP Small: 4384 x 2466, 16:9, 10.8MP [3] Video Resolution 1920 x 1080 60i, 16:9 1920 x 1080 30p, 16:9 1920 x 1080 25p, 16:9 1280 x 960 30p, 4:3 1280 x 960 25p, 4:3 1280 x 720 60p, 16:9 1280 x 720 30p, 16:9 640 x 480 30p, 4:3（VGA） Three Field of View (FOV) options are supported when shooting in 1920x1080 60i, 1920x1080 30p and 1920x1080 25p: Wide (120°), Medium (110°) and Narrow (85°).
400 [6] White Balance AWB (auto) Sunny Cloudy Indoor [7] Exposure Metering Center Average Spot [8] Exposure Compensation -2.0（EV） 2.0（EV） -1.7（EV） 1.7（EV） -1.3（EV） 1.3（EV） -1.0（EV） 1.0（EV） -0.7（EV） 0.7（EV） -0.3（EV） 0.3（EV） 0（EV） [9] Sharpness Standard Hard Soft [10] Anti-flicker Auto 50Hz 60Hz [11] Restore Default Settings Restores all camera default settings. Camera reboot is needed to allow restoration to take effect. ©2014 DJI. All Rights Reserved.
[12] Format SD Card Format the Micro-SD card. All data stored in the Micro-SD card will be lost after formatting. Remember to backup before formatting. 12.3 Album Page Camera SD CARD Album Browse thumbnails of photos and videos stored on the Micro-SD card. Tap to view photo or watch video. [4] [1] [3] [2] [1] Photos and Videos are listed and grouped by date. [2] All photos and videos that have already been synced to your mobile device are identified with the icon.
to select photos or videos to synchronize to your mobile device (The thumbnails identified by the check mark are successfully selected.). Or you can select one or more groups to be synchronized by checking the box before the group, and then Tap to start synchronizing. During the synchronization process, users can tap to cancel the synchronization. Photos and videos that have been synchronized to the mobile device will remain. Some mobile devices may fail to support synchronization of 1080i60 video files.
[2] Photos and videos are listed in thumbnail style and sorted by capture time. [3] Pictures and videos are sorted by captured/recorded Geo-tagged locations. Access to the Internet is required to load a map. Geo-tagged locations [4] Tap any thumbnail for single view; you can slide left or right to view the previous or next photo. Tap a video thumbnail to play a single video. [5] [5] Tap to share your photos and videos to social network sites.
News List News Details 12.5 Settings Page [6] [1] [7] [2] [8] [3] [9] [4] [10] [11] [5] [12] [13] [14] [1] Toolbar Auto Hide Slide the switch from left to right to enable this function. The toolbar will auto hide on the camera page. Toolbar Auto Hide Disabled [2] When Connection Breaks ©2014 DJI. All Rights Reserved.
[15] [16] [15] Stop Recording: Enabled: Stop recording when the Wi-Fi connection between the mobile device and the camera breaks while the camera is recording. Disabled: Keep recording when the Wi-Fi connection between the mobile device and the camera breaks while the camera is recording. [16] Select the state the camera will enter in the event of a Wi-Fi Connection break between the mobile device and the camera.
High: 640 x 480@15fps Medium: 320 x 240@30fps Low: 320 x 240@15fps (Recommended when there is a lot of interference.) [5] Parameter Unit Select imperial or metric units of measurement. [6] Auto Flips The user interface of the DJI PHANTOM 2 VISION App will flip if the mobile device’s auto-flip is enabled. [7] Low Battery Warning If enabled, an alarm will sound when the battery level is too low. Be sure sound is enabled on the mobile device and try to adjust the volume to the highest level.
My location My location PHANTOM 2 VISION’ S location PHANTOM 2 VISION’ S location Satellite Mode Standard Mode [12] Account Tap to see user’s account information. [13] Rate Tap to rate the DJI VISION App. Internet access is required. [14] About Tap to see the current version of the DJI VISION App and also for contact information. 12.5 Ground Station The DJI Vision app features an integrated ground station function.
12.5.1 Ground Station GUI [2] [1] [3] [4] [5] [6] [9] [11] [12] [13] [14] [10] [15] [16] [7] [1] [8] MODE Modes include Hover：Hovering Waypoint：Mission in progress GoHome：Returning to home point Take off：Taking off Landing：Landing GPS： GPS flight Atti.：Atti. flight Manual：Manual flight [2] Approximated Flight Mission Distance Planned mission distance. To achieve optimum battery performance, max mission distance is restricted to 5km (3miles).
Battery level display. Refer to [6] in “Using the DJI Vision app” for details [6] GPS Number of satellites connected. Refer to [7] in “Using the DJI Vision app” for details [7] Flight Attitude and Radar Attitude and Radar display. Refer to [3] in “Using the DJI Vision app” for details [8] Flight Parameters Flight information display. Refer to [4] in “Using the DJI Vision app” for details [9] Back Return to camera GUI. [10] Home Point Locator Locate your Home point.
12.5.2 Using Ground Station Step 1 Launching Ground Station： Enable ground station feature from DJI Vision app Settings and a disclaimer for ground station prompts. Read the disclaimer thoroughly before starting to use ground station. Ensure your mobile device has access to the Internet. Due to the map data required, Wi-Fi connection is recommended. Internet access is required to cache the ground station map, if Wi-Fi is unavailable, mobile data service is required.
A red circle on the map, as shown in the screenshot below, indicates a restricted, No Waypoint area. Waypoints cannot be placed in this area. For more information, refer to “6.2 Flight Restriction of Restricted Areas (P46)”. To achieve the optimal video transmission quality, the aircraft is set to operate within a 500m-radius area from Home point. Tap on a waypoint to open a waypoint properties window. Slide the white dot right to adjust waypoint altitude.
This prompt lists all waypoints and their altitudes. The aircraft will fly to each waypoint listed. If there is a difference in altitude between waypoints, the aircraft will adjust its altitude as it flies between points. When ready, tap “GO” to begin mission. Aircraft reacts differently to the “GO” command： If aircraft is on the ground, the aircraft takes off automatically and ascend 16 feet (5m) then fly to the first waypoint. If aircraft is in the air, the aircraft flies to the first waypoint.
13 Assistant Software Installation and Configuration 13.1 Installing Driver and PHANTOM 2 VISION Assistant Software Installing and running on Windows 1. Download driver installer and Assistant Software installer in EXE format from the download page of PHANTOM 2 VISION on the DJI website. 2. Connect the PHANTOM 2 VISION to a PC via a Micro-USB cable. 3. Run the driver installer and follow the prompts to finish installation. 4.
Installer in DMG format supports only Mac OS X 10.6(Lion) or above. Usage of PHANTOM 2 VISION Assistant Software on Mac OS X and Windows are exactly the same. The Assistant Software pages appear in other places of this manual are on the Windows for example. 13.2 Using the PHANTOM 2 VISION Assistant Software on a PC 1. Start up the PC, power on the PHANTOM 2 VISION, then connect the PHANTOM 2 VISION to the PC with a Micro-USB cable. DO NOT disconnect until configuration is finished. 2.
(1) Users should not enable the Naza-M function before finishing the “Advanced Flight Maneuvers” procedure, in accordance with the "Phantom Pilot Training Guide”. If the Naza-M function is enabled, users can switch the control mode to either the ATTI. Mode, GPS Mode or Manual Mode, and access the advanced settings (e.g. IOC). In addition, the LED located on the rear frame arms will display the flight status according to the Naza-M's indicator, instead of the Phantom 2 Vision's indicator.
Firmware upgradable items: (1) Main Controller (2) GPS (3) 5.8G Receiver (4) P330CB (Main Board) (5) Battry 13.4 PHANTOM RC Assistant Software Description Please follow the procedures to finish the configuration of the remote controller. 1. Turn off the remote controller and find the Micro-USB port on the back of it. (If there is no one, users should open the rear cover to find the Micro-USB port on the board inner the remote controller.) 2.
14 Troubleshooting（FAQ） 14.1 How to solve large margin(s) mid-point error? If the Remote Controller stick(s) mid-point margin of error is too big, the motors will fail to start when you execute the Combination Stick Commands (CSC) and the aircraft will not take off.
14.6 Files fail to synchronize. Solution: Video files that are too large (file sizes close to 4GB) cannot be synchronized to the mobile device. Some mobile devices also fail to support synchronization of the 1080i60 video files. 14.7 Albums fail to synchronize. Solution: Reset the settings of your mobile device as illustrated below. Enable the Settings ->Private->Photos->DJI VISION. Otherwise the Albums will fail to synchronize with your mobile device. 14.8 Failure to share.
14.10 Usage tips for the App used on multiple mobile devices. During flight, if you use the App on multiple mobile devices, please turn off the App on the first mobile device, and then turn on the App on the second one to ensure the App can work normally on the second mobile device. 14.11 How to land the aircraft smoothly in a better way? First pull the throttle stick position down to lower than 5%, then execute the CSC command to stop the motors. 14.
2nd Level Low Battery Capacity Warning Not Stationary or Sensor Bias is too big Error* Compass Needs Calibration *You can figure out the error by connecting the PHANTOM 2 VISION to the PHANTOM 2 VISION’s Assistant Software. ©2014 DJI. All Rights Reserved.
Specifications Aircraft Supported Battery DJI 5200mAh Li-Po Battery PHANTOM 2 VISION Weight 1160g Recommend payload ≤1300g Maximum payload 1350g Hovering Accuracy (Ready to Fly) Vertical: 0.8m; Horizontal: 2.5m Max Yaw Angular Velocity 200°/s Max Tiltable Angle 35° Max Ascent / Descent Speed Ascent: 6m/s; Descent: 2m/s Max Flight Speed 15m/s (Not Recommended) Wheelbase 350mm Tilting Range of Gimbal 0° - 60° Remote Controller Operating Frequency 5.728 GHz－5.
Samsung Galaxy S3, S4, Note2, Note3 or phones of similar configuration. System Requirement of Mobile Device ©2014 DJI. All Rights Reserved. iOS 6.0 or above; Android system 4.
