C User Manual v1.0 2020.
Contents 2 Using this Manual Legend 2 Before You Begin 2 Download the Ronin App 2 4 Introduction 5 DJI RSC 2 Diagram 6 Getting Started Unfolding the Gimbal 6 Attaching the Extended Grip/Tripod 6 Unlocking and Locking the Gimbal 7 Mounting the Camera 7 Balancing 9 12 Grip and Built-In Battery Charging 12 Safety Guidelines 12 16 Operations Activating DJI RSC 2 16 Screen Operation 16 Ronin App Settings 19 Image Transmission 27 Operation Modes 28 Updating Firmware 29 Mainten
DJI RSC 2 User Manual DJI RSC 2 Diagram 1 2 13 12 14 15 16 24 23 22 21 11 10 9 3 4 5 6 7 20 19 17 18 8 1. Tilt Motor 14. Image Transmission/Focus Motor Port 3. Screen 15. Focus Motor Port (USB-C) 5. Camera Control Button 17. Front Dial 2. Tilt Lock 4. Side Dial 6. M Button 7. Joystick 8. Extended Grip/Tripod 9. Back Button 10. M4/NATO Port 11. Lock Knob 12. Lower Quick-Release Plate 13. Upper Quick-Release Plate (USB-C) 16. RSS Camera Control Port (USB-C) 18. Trigger 19.
Getting Started Unfolding the Gimbal Loosen the lock knob to the unlocked position, unfold the gimbal as shown, and tighten the lock knob to the locked position. 2 1 3 Attaching the Extended Grip/Tripod 1 2 3 6 © 2020 DJI OSMO All Rights Reserved.
DJI RSC 2 User Manual Unlocking and Locking the Gimbal To unlock the gimbal, toggle the tilt, roll, and pan lock levers to the unlocked position. Adjust the gimbal position as shown and toggle the three locks to the locked position. Tilt Lock Roll Lock Pan Lock Mounting the Camera Supported Cameras and Lenses DJI RSC 2 has been rigorously tested to support a payload of 3 kg. Make sure the combined weight of the camera, lens, and other accessories are within 3 kg.
DJI RSC 2 User Manual A camera riser is required when using a focus motor or a small camera with a large lens, such as a Sony A6400 with the Sony FE 24-70 f2.8 GM lens. 2. Attach the Lower Quick-Release Plate and Lens Support Toggle the lever on the lower quick-release plate to the unlocked position camera 2 , and toggle the lever to the locked position the lens support to the lower quick-release plate support* when using a long or heavy lens. 4 3 1 , insert the after it is engaged. Attach .
DJI RSC 2 User Manual To remove the lower quick-release plate from the gimbal, toggle the lever on the camera mounting plate to the unlocked position and remove the lower quick-release plate while pressing the safety lock on the mounting plate. Safety Lock Lever RSS Camera Control Port 4. Connect the Camera Control Cable Choose the proper camera control cable according to the camera type.
DJI RSC 2 User Manual 1 2 2. Balancing Depth for the Tilt Axis a. Rotate the tilt axis so that the camera lens is pointing forward. Toggle the lever to the unlocked position 1 . b. Check to make sure the camera is not front or back-heavy. If front-heavy, move the camera backward 2 . If back-heavy, move the camera forward 2 . c. Toggle the lever to the locked position. The tilt axis is balanced when the camera is steady while tilted up or down by 45°. d. Lock the tilt axis. 1 2 3.
DJI RSC 2 User Manual 1 2 4. Balancing the Pan Axis a. Unlock the pan axis. Loosen the knob 1 . b. While holding the grip, tilt DJI RSC 2 forward, and rotate the pan arm until parallel with you. c. Check the movement of the pan axis. If the camera lens rotates to the left, push the pan axis to the right the left 2 . 2 . If the camera lens rotates to the right, push the pan axis to d. Tighten the knob. The pan axis is balanced if the camera is steady when rotating the pan while tilting the grip.
Grip and Built-In Battery The grip is for handheld use. The built-in battery within the grip has a capacity of 3400 mAh and the maximum runtime is 14 hours (when DJI RSC 2 is properly balanced). Charging Before using for the first time, charge DJI RSC 2 through the power port using a charging cable (included) and a USB adapter (not included). It is recommended to use a QC 2.0 or PD USB adapter (max. 18W). Check the battery level on the screen.
DJI RSC 2 User Manual To avoid fire, serious injury, and property damage, observe the following safety guidelines when using, charging, or storing the grip. Grip Use 1. DO NOT allow the grip to come into contact with any kind of liquid. DO NOT leave the grip out in the rain or near a source of moisture. DO NOT drop the grip into water.
DJI RSC 2 User Manual Grip Storage 1. Keep the grip out of the reach of children and animals. 2. If the grip will be stored for an extended period, charge the grip until the battery level reaches between 30% and 50%. 3. DO NOT leave the grip near heat sources such as a furnace or heater. DO NOT leave the grip inside of a vehicle on hot days. The ideal storage temperature is 22° to 28° C (72° to 82° F). 4. Keep the grip dry. Grip Maintenance 1.
DJI RSC 2 User Manual Grip Maintenance 1. Battery life may be reduced if not used for an extended period. 2. Discharge and charge the grip completely once every three months to keep it in good condition. Grip Disposal 1. If the grip is disabled and the battery cannot be fully discharged, contact a professional battery disposal or recycling agent for further assistance. 2. Dispose of the grip immediately if it cannot be powered on after over-discharging. © 2020 DJI OSMO All Rights Reserved.
Operations Activating DJI RSC 2 DJI RSC 2 needs to be activated through the Ronin app before using for the first time. 1. Press and hold the power button to power on the gimbal. 2. Enable Bluetooth on your mobile device and launch the Ronin app. Once detected in the list of Bluetooth devices, select DJI RSC 2 and input the default Bluetooth password: 12345678. Make sure you are connected to the internet and follow the on-screen instructions to activate DJI RSC 2.
DJI RSC 2 User Manual Auto Tune: press the side dial to select Auto Tune after balancing the gimbal. If the lens-fastening strap is installed, users can enable SuperSmooth prior to auto tune for optimal performance. SuperSmooth will take effect after auto tune completed. The stiffness can be adjusted on the auto tune screen. Follow Mode Settings: tap to select follow mode and speed.
DJI RSC 2 User Manual Button Functions Power Button Press and hold to power on or off. Tap or press twice to enter or exit sleep mode. Joystick Push up or down to control the movement of the tilt axis and left or right to control the movement of the pan axis (default setting). Camera Control Button* Press halfway for autofocus. Press once to start or stop recording. Press and hold to take a photo. Front Dial* Turn to control focus (default setting).
DJI RSC 2 User Manual Ports NATO ports can be used to attach a Briefcase Handle and Twist Grip Dual Handle. Ronin App Settings The Ronin App is easy to use to control gimbal movement and parameter settings with intelligent functions such as Panorama, Timelapse, and Track, as well as more features of the gimbal and the DJI Ronin RavenEye Image Transmission System. The screenshots below are based on the iOS version of the app. Top Bar Sleep/Wake: tap to enter or exit sleep mode.
DJI RSC 2 User Manual Create Virtual Joystick 1 2 3 4 6 5 Use the virtual joystick in the app to control the movement of the gimbal and to shoot. 1. Control Bar: control the speed and smoothness of the gimbal by adjusting the control bar. Speed allows users to adjust the remote-controlled rotational speed. Smoothness allows users to adjust the sensitivity of the gimbal. The lower the smoothing value, the more sensitive the movement of the gimbal. 2.
DJI RSC 2 User Manual Force Mobile Force Mobile requires the phone holder and a mobile phone mounted on a tripod or handlebar vertically. After enabling this feature in the Ronin app, the gimbal movement can be controlled by tilting and rotating your mobile phone. Speed determines the relationship between the rotational speed and angle. When the speed is set to 50, the angle of rotation for the gimbal and mobile phone is 1-to-1. The gimbal will move at an identical angle to the mobile phone.
DJI RSC 2 User Manual Make sure you have connected the camera and gimbal using the corresponding camera control cable before using Panorama. Overlap: determines the overlap ratio of every photo when generating a panorama. The interval time between shooting photos should be set to one second more than the shutter time to avoid blurred footage when using a long exposure.
DJI RSC 2 User Manual In Timelapse, DJI RSC 2 triggers the camera to capture still images with the set interval time and will automatically stop when completed. The duration for the Timelapse and the frame rate can be set so that DJI RSC 2 can calculate the exact number of images required. By enabling Push mode, users can manually adjust the pan and tilt axes before starting the Timelapse. Users can push DJI RSC 2 to alter the camera orientation and adjust the framing.
DJI RSC 2 User Manual Gaming Controller PS4 DualShock and Xbox controllers can be used to control the gimbal and camera. After connecting the controller to the mobile device and gimbal, users can control gimbal movements, focus and zoom, and can record videos, recenter gimbal, capture photos, and switch profiles. The speed and smoothness of the control sticks can be adjusted. Set the focus value within 10 on the camera settings for optimal performance. iOS 13 or higher, Android 9.
DJI RSC 2 User Manual Motor Parameters Auto Tune: the stiffness value is determined by the payload of the gimbal. Use Auto Tune to obtain the stiffness value automatically after balancing. Tap Auto Tune and DJI RSC 2 automatically calculates the result based on the weight of the gimbal setup. Alternatively, press and hold the M button and trigger simultaneously for four seconds to start auto tune without using the app. The auto tune process takes approximately 15 to 30 seconds.
DJI RSC 2 User Manual User Profile Three user profiles can be set and saved. Choose from Pan and Tilt Follow, FPV, Customized, and 3D Roll 360. Speed: determines how fast the camera travels while translating a pan, tilt, or roll movement. Deadband: determines how much movement the gimbal tolerates prior to translating the pan, tilt, and roll movement of the camera. Push: after enabling Push, the gimbal axis can be manually pushed to the desired position.
DJI RSC 2 User Manual Endpoint: limits the rotational range of the gimbal by setting the endpoints. The pan axis has a slip-ring, enabling DJI RSC 2 to rotate continuously when the endpoints are set to 180°. On the tilt axis, you can set up the endpoints according to your requirements. Some longer lenses may hit the gimbal frame. Set the endpoint angle to prevent such cases.
