MATRICE 600 PRO User Manual V1.0 2016.
Searching for Keywords Search for keywords such as “battery” and “install” to find a topic. If you are using Adobe Acrobat Reader to read this document, press Ctrl+F on Windows or Command+F on Mac to begin a search. Navigating to a Topic View a complete list of topics in the table of contents. Click on a topic to navigate to that section. Printing this Document This document supports high resolution printing.
Using This Manual Legends Warning Important Hints and Tips Reference Information The MATRICETM 600 Pro does not include a gimbal or camera. A corresponding gimbal or camera is required for certain functions mentioned in this manual. Before Flight The following tutorials and manuals have been produced to help you get the most out of your Matrice 600 Pro. 1. In the Box 2. Disclaimer and Safety Guidelines 3. Quick Start Guide 4. Intelligent Flight Battery Safety Guidelines 5.
Warning The rotating propellers can cause serious damage and injury. Fly with caution at all times. Assembly Warning 1. Ensure that all other parts are installed before inserting the Intelligent Flight Batteries. 2. DO NOT remove any glued-in screws. 3. The Matrice 600 Pro should be lifted off the ground when testing the landing gear or recalibrating servo travel. Flight Warning 1. The aircraft is not waterproof. DO NOT fly in rainy or snowy weather. 2.
Contents Using This Manual 1 Warning 2 Product Profile 5 Introduction 5 Highlighted Features 5 Installation 6 Mounting the Landing Gear 6 Unfolding the Aircraft 6 Mounting the Gimbal (Optional) 7 Intelligent Flight Battery Profile 8 8 Intelligent Flight Battery Functions 8 Using the Batteries 9 Remote Controller 14 Profile 14 Preparing Remote Controller 14 Remote Controller Overview 14 Remote Controller Operations 16 Dual Remote Controllers Mode 21 Remote Controller LEDs
DJI GO App 32 Editor 35 Skypixel 35 Me 35 Flight 36 Flight Environment 36 Flight Limits and No Fly Zones 36 Pre-Flight Checklist 39 Flight Status Indicators 40 Calibrating the Compass 41 Auto Takeoff and Auto Landing 42 Starting and Stopping the Motors 42 Stopping the Motors Mid-flight 43 Flight Test 43 Appendix 4 32 Equipment 44 Specifications 44 Intelligent Flight Modes 47 Upgrading the Firmware 48 Retractable Landing Gear 49 Reserved Mounting Position Dimensions
Product Profile Introduction The Matrice 600 Pro is a six-rotor flying platform designed for professional aerial photography and industrial applications. It is equipped with a dedicated DJITM A3 Pro triple-modular redundancy system and advanced intelligent flight functions, ensuring safe and stable operation at all times. Its mechanical design, with quick-release landing gear and mounted folding arms, make it easy to transport, store, and prepare for flight. With a maximum takeoff weight of 15.
Installation Mounting the Landing Gear 1. Ensure the screw on the landing gear leg is pointing in the same direction as the gap next to the knob on the landing skid. Insert both landing gear legs into a corresponding landing skid, rotate the landing gear leg until it is fully seated into the landing skid, and then secure it in place by tightening the knob. 2. Ensure the hook on the landing gear leg is facing toward the outside of the aircraft, then attach it to the connector on the aircraft body.
MATRICE 600 PRO User Manual Mounting the Gimbal (Optional) The built-in flight control system of the Matrice 600 Pro is compatible with the following DJI gimbals and cameras. Ronin-MX Zenmuse Z30 Zenmuse X3 Zenmuse X5 Series Zenmuse XT Zenmuse Z15 Series HD Gimbal: Z15-A7, Z15-BMPCC, Z15-5D III, Z15-GH4 Different accessories are used to mount different gimbals or cameras. Purchase corresponding accessories according to your needs. Refer to DJI Zenmuse X3 Gimbal and Camera (p.
Intelligent Flight Battery Profile The Matrice 600 Pro has six battery compartments and six Intelligent Flight Batteries to extend the flight time. The standard Intelligent Flight Battery has a capacity of 4500mAh, voltage of 22.2V, and built-in smart charge-discharge function. It can only be charged with an appropriate DJI approved charger. Intelligent Flight Battery DJI Hex Charger The Intelligent Flight Battery must be fully charged before first-time use. Intelligent Flight Battery Functions 1.
MATRICE 600 PRO User Manual Using the Batteries Installing the Batteries There are six battery compartments on the Matrice 600 Pro. You must load all six battery compartments with batteries of the same model before each flight. Make sure all the batteries are fully charged before each flight. Never insert the Intelligent Flight Battery into or remove it from the battery compartment of the Matrice 600 Pro when it is powered on.
MATRICE 600 PRO User Manual If the power supply is not OK when powering on the batteries, the DJI GO app will either prompt you to adjust the battery positions or tell you there is a large voltage difference. To adjust the battery positions: 1. Power off all the batteries. 2. Adjust battery positions by following the tips in the DJI GO app. 3. Ensure all the battery positions are correct and then power on one of the batteries. The other batteries will power on automatically if the positions are correct.
MATRICE 600 PRO User Manual Battery Level Indicator LED1 LED2 LED3 LED4 Battery Level 87.5%~100% 75%~87.5% 62.5%~75% 50%~62.5% 37.5%~50% 25%~37.5% 12.5%~25% 0%~12.5% =0% Checking the Battery Life The battery life indicates the number of cycles the battery can be charged and discharged before it must be replaced. When the battery is powered off, press and hold the power button for 5 seconds to check the battery life.
MATRICE 600 PRO User Manual Charging the Intelligent Flight Battery The Matrice 600 Pro is shipped with a DJI Hex Charger. It can charge up to six Intelligent Flight Batteries and two remote controllers simultaneously. 1. Connect the Hex Charger to a power outlet (100-240V, 50/60Hz) with the power cable. 2. Insert the Intelligent Flight Battery into the battery port to begin charging. 3.
MATRICE 600 PRO User Manual Charging Protection LED Display The table below describes the battery protection mechanisms and their corresponding LED patterns.
Remote Controller Profile The remote controller integrates video downlink and aircraft control into one system. The combined system operates at 2.4 GHz with a maximum signal transmission range of 5 km. The device features a number of standard and customizable buttons that allow users to quickly access certain aircraft functions, such as taking and reviewing photos/videos, as well as controlling the gimbal and landing gear. It is powered by a 2S rechargeable battery.
MATRICE 600 PRO User Manual [5] Landing Gear Control Switch Toggle the switch up or down to raise or lower the landing gear. [6] Battery Level LEDs [8] Power Button Used to power on or power off the remote controller. [9] RTH Status LED Displays the current battery level. Circular LED around the RTH button displays RTH status. [7] Status LED Displays the power status. [16] [18] [17] set number of photos will be taken with one press.
MATRICE 600 PRO User Manual Remote Controller Operations Powering On and Off the Remote Controller The Matrice 600 Pro remote controller is powered by a 2S rechargeable battery with a capacity of 6000mAh. The battery level is indicated by the Battery Level LEDs on the front panel. Follow the steps below to power on your remote controller: 1. When powered off, press the Power Button once and the Battery Level LEDs will display the current battery level. 2.
MATRICE 600 PRO User Manual Controlling the Camera Shoot videos or images and adjust camera settings via the Shutter Button, Camera Settings Dial, Playback Button and Video Recording Button on the remote controller when using a Zenmuse X3, X5 series or XT gimbal and camera. [1] [4] [2] [3] [1] Camera Settings Dial Turn the dial to quickly adjust camera settings such as ISO and shutter speed without letting go of the remote controller.
MATRICE 600 PRO User Manual Remote Controller Aircraft ( indicates nose direction) Function Moving the Left Stick up/down changes the aircraft’s elevation. Push it up to ascend and down to descend. Use this stick to take off when the motors are spinning at idle speed. The aircraft will hover in place if the Left Stick is released. Moving the Left Stick left/right changes the heading of the aircraft. Push it left to rotate the aircraft counter clock-wise, and right to rotate the aircraft clockwise.
MATRICE 600 PRO User Manual Flight Mode Switch Toggle the switch to select the desired flight mode. You may choose between P-mode, A-mode and F-mode. Figure P Flight Mode P P-mode A A-mode F F-mode A F P-mode (Positioning): P-mode works best when GPS signal is strong. There are several states in P-mode which are automatically selected by the Matrice 600 Pro depending on GPS signal strength: P-GPS: GPS is available. The aircraft uses GPS for positioning. P-ATTI: GPS is not available.
MATRICE 600 PRO User Manual By default, the landing gear will not raise or lower if you toggle the control switch when the aircraft is on the ground. Go to the DJI GO app > Camera View > > Advanced Settings > Disable Landing Gear Auto-Lock, and then the landing gear will raise or lower if you toggle the control switch when the aircraft is on the ground. Ensure that the switch is in the lower position when enabling this feature. The feature will be disabled after raising and lowering the landing gear once.
MATRICE 600 PRO User Manual Optimal Transmission Range The signal transmission between the aircraft and the remote controller performs best when the aircraft is within the optimal transmission range. Open up the antennas on the remote controller to optimize transmission range. Ideally, the flat surface of the antenna should be facing the aircraft. If the signal is weak, fly the aircraft closer to you.
MATRICE 600 PRO User Manual Setting Up Dual Remote Controllers Mode The Dual Remote Controllers mode is disabled by default. Users must enable this feature on the Master Remote Controller through the DJI GO app. Follow the steps below for setup: Master Remote Controller: 1. Connect the remote controller to your mobile device and launch the DJI GO app. 2. Go to the Camera View, and tap to enter the remote controller settings window. 3.
MATRICE 600 PRO User Manual 2. Tap Search for Master Controller to register the Master remote controller. Remote Controller Settings Remote Controller Settings Master and Slave Set Remote Controller Status Remote Controller Name OFF Master Slave S88642 Request Control Remote Controller Settings Search for Master Controller Master RC List T12254 Remote Controller Settings Master and Slave 3.
MATRICE 600 PRO User Manual Status LED Alarm Remote Controller Status — Solid Red chime The remote controller is set as Master but is not connected to the aircraft. — Solid Green chime The remote controller is set as Master and connected to the aircraft. — Solid Purple 2 beeps The remote controller is set as Slave but is not connected to the aircraft. — Solid Cyan 2 beeps and chime The remote controller is set as Slave and connected to the aircraft.
MATRICE 600 PRO User Manual 3. The remote controller Status LED will blink blue and beep to indicate that the remote controller is ready to be linked. Remote Controller Settings Remote Controller Calibration Stick Mode Searching for aircraft frequency, Default stick mode is Mode 2, changing stick modes alters the way the aircraft is controlled. timeout in 54 seconds Do not change unless familiar with your new mode.
Return-to-Home (RTH) Profile The Return-to-Home (RTH) function brings the aircraft back to the last recorded Home Point. There are three events that will trigger RTH procedure: Smart RTH, Low Battery RTH and Failsafe RTH. Description GPS The default Home Point is the first location where your aircraft received strong GPS signals (i.e. the white GPS icon is followed by at least four white bars ). You can update the Home Point via the DJI GO app. Refer to Updating Home Point (p. 28) for details.
MATRICE 600 PRO User Manual Battery Level Aircraft Status Indicator Description Flight Instructions DJI GO App Tap Go-Home to make the aircraft return to Home Point Low Battery The battery level is Warning low. Please land the aircraft. Aircraft Status and land automatically, or Indicator Cancel to resume normal blinking RED flight. If no action is taken, slowly. the aircraft will automatically return to the Home Point and land after 10 seconds.
MATRICE 600 PRO User Manual RTH Safety Notices The aircraft cannot avoid obstruction during RTH, therefore it is important to set a reasonable RTH altitude before each flight. Go to the DJI GO app > Camera View > > Set Return-to-Home Altitude.
A3 Pro Redundancy System The Matrice 600 Pro’s A3 Pro flight control system is an upgraded version of the A3, which enhances flight safety. The A3 includes a flight controller, GPS-Compass Pro and a PMU (Power Management Unit). With two additional IMU Pro and GPS-Compass Pro modules, the A3 Pro provides triple-modular redundancy, improving the system’s anti-risk performance. Mounting Positions Ensure that the settings of all the IMU Pro modules and GPS-Compass Pro modules are correct before each flight.
DJI Assistant 2 When using your Matrice 600 Pro for the first time, activate it in the DJI Assistant 2 software. Installation and Launching 1. Download the DJI Assistant 2 installation file from the official DJI website: http://www.dji.com/matrice600-pro/info#downloads 2. Complete the installation for the DJI Assistant 2 software. 3. Launch the DJI Assistant 2 software. Using the DJI Assistant 2 1. Ensure that all the six Intelligent Flight Batteries are fully charged and then install them. 2.
MATRICE 600 PRO User Manual API Control and the Intelligent Flight Modes cannot be used at the same time. If you are using Intelligent Flight Mode, finish the current intelligent flight mission and toggle the Flight Mode Switch to F-mode again to use API Control. API Control is automatically disabled after firmware updates. Re-enable this option if necessary.
DJI GO App Use the DJI GO app to configure your aircraft. If using a gimbal or camera, you can also control the gimbal or camera in the app. The Library, Skypixel, and Me sections in the app allow you to share your content with friends. 4:21PM iPad 22% MATRICE 600 PRO Aircraft Connected Camera Learn more Equipment Editor Skypixel Me Equipment On the Equipment page, you can enter Camera View, visit the Academy or view your flight records.
MATRICE 600 PRO User Manual [1] System Status : Indicates the current aircraft system status and GPS signal strength. Ready to Go (GPS) [2] Battery Level Indicator : Describes the battery level of the aircraft according to its immediate status. The colored zones represent the various stages of battery level. When the battery level drops to a certain stage, the system will prompt the user to take the appropriate action. [3] Flight Mode : The text next to this icon indicates the current flight mode.
MATRICE 600 PRO User Manual [10] Mini Map Displays the flight path of the current flight. Tap the Mini Map to switch between Camera View and Map View. [11] Flight Telemetry D 210 M H H.S 4.2 M/S 30 M VS 2.3 M/S 232 M Flight Attitude and Radar Function: The aircraft’s flight attitude is indicated by the target-like icon. (1) The red arrow shows which direction the aircraft is facing. (2) The ratio of the grey area to the blue area indicates the aircraft’s pitch.
MATRICE 600 PRO User Manual Follow Mode The gimbal’s orientation is aligned with the aircraft’s nose. One user alone can control the pitch motion of the gimbal, but a second operator is required to control the yaw motion using a second remote controller. FPV Mode The gimbal will lock to the movement of the aircraft to provide a FirstPerson-View flying experience. Free Mode The gimbal’s motion is independent of the aircraft’s orientation.
Flight Once pre-flight preparation is complete, it is recommended to use the flight simulator to learn how to fly safely. Ensure that all flights are carried out in an open area. Flight Environment 1. Do not use the aircraft in adverse weather conditions including rain, snow, fog, and wind speeds exceeding 8 m/s. 2. Only fly in open areas. Tall buildings and steel structures may affect the accuracy of the compass and the GPS signal. 3.
MATRICE 600 PRO User Manual Safe to Fly (GPS) Blinking Green Slowly Flight Limits DJI GO App Max Height Flight altitude must be below the preset height. Warning: Height limit reached. Max Radius Flight distance must be within the max radius. Warning: Distance limit reached. Safe to Fly (No GPS) Blinking Yellow Slowly Flight Limits DJI GO App Max Height If the Max Flight Altitude set in the DJI GO app is ≤ 50m*, the flight altitude will not exceed the preset value.
MATRICE 600 PRO User Manual 2. R1 miles around the airport (depending on its shape and size) encompasses the no fly zone, inside of which takeoff and flight are prohibited. 3. From R1 to R1+1 miles around the airport, the flight altitude is limited at a 15 degree incline, starting at 66 feet (20 meters) from the edge of airport and radiating outwards. The flight altitude is limited to 1640 feet (500 meters) at R1+1 miles. 4.
MATRICE 600 PRO User Manual Safe to Fly (GPS) Zone No Fly Zone AltitudeRestricted Zone Warning Zone Free Zone Blinking Green Slowly Aircraft Status Indicator Restrictions DJI GO App Warning Motors will not start. Warning: You are in a no fly zone. Takeoff prohibited. If the aircraft loses GPS signal and enters the restricted area but regains GPS signal afterwards, the aircraft will enter SemiAutomatic Descent and land itself. Warning: You are in a no fly zone. Automatic landing has begun.
MATRICE 600 PRO User Manual 5. All cables are connected correctly and firmly. 6. The DJI GO app is connected to the aircraft. 7. Motors start properly and are functioning as normal. Flight Status Indicators ESC LEDs Aircraft Status Indicator ESC LEDs There is an ESC LED on each frame arm of the Matrice 600 Pro to show the orientation of the aircraft after motors started. The ESC LEDs located on frame arms M1 and M2 are red. The ESC LEDs located on frame arms M3 to M6 are green.
MATRICE 600 PRO User Manual Warning Blinking Yellow Rapidly Blinking Red Slowly Blinking Red Rapidly Blinking Red Rapidly for 0.
MATRICE 600 PRO User Manual When to Recalibrate 1. The compass data is abnormal, and the Aircraft Status Indicator is blinking red and yellow alternatively. 2. Flying in a new location, or a location that is different from your last flight. 3. The mechanical structure of the Matrice 600 Pro is changed, i.e. the mounting position of the GPS module is changed. 4. Severe drifting occurs in flight, i.e. the Matrice 600 Pro has difficulty flying in a straight line.
MATRICE 600 PRO User Manual Stopping the Motors There are two methods to stop the motors. Method 1: When the Matrice 600 Pro has landed, push the throttle stick down, then perform the CSC command to stop the motors. Release both sticks once the motors have stopped. Method 2: When the aircraft has landed, push the throttle down and hold. The motors will stop after 3 seconds.
Appendix Specifications Aircraft Structure Diagonal Wheelbase Dimensions 1133 mm 1668 mm × 1518 mm × 727 mm with propellers, frame arms and GPS mount unfolded (including landing gear) 437 mm × 402 mm × 553 mm with propellers, frame arms and GPS mount folded (excluding landing gear) Package Dimensions 520 mm × 480 mm × 640 mm (L × W × H) Intelligent Flight Battery Quantity 6 Weight (with six TB47S batteries) 9.5 kg Weight (with six TB48S batteries) 10 kg Max Takeoff Weight 15.
MATRICE 600 PRO User Manual Remote Controller 920.6 MHz to 928 MHz (Japan) Operating Frequency 5.725 GHz to 5.825 GHz 2.400 GHz to 2.483 GHz Max Transmitting Distance FCC: 5 km (unobstructed, free of interference) CE: 3.5 km 10 dBm @ 900 M EIRP 13 dBm @ 5.8 G 20 dBm @ 2.
MATRICE 600 PRO User Manual Battery (Optional) Model TB48S Capacity 5700 mAh Voltage 22.8 V Type LiPo 6S Energy 129.96 Wh Net Weight 680 g Operating Temperature 14° to 104° F (-10° to 40° C) Storage Temperature Less than 3 months: -4° to 113° F (-20° to 45° C) More than 3 months: 72° to 82° F (22° to 28° C) Charging Temperature 41° to 104° F (5° to 40° C) Max Charging Power 180 W 46 © 2016 DJI All Rights Reserved.
MATRICE 600 PRO User Manual Intelligent Flight Modes Intelligent Flight Modes allow users to lock the orientation of the aircraft in different fashions or to preplan flight paths. Intelligent Flight Modes only work in F-mode, and users must toggle the flight mode switch to F-mode to activate Intelligent Flight Modes. Point of Interest (POI) Waypoints Record a point of interest (POI). The aircraft’s nose always points towards the POI.
MATRICE 600 PRO User Manual Upgrading the Firmware Upgrading the Aircraft and Lightbridge 2 Air System Firmware Connect the aircraft to the DJI Assistant 2 to upgrade the aircraft’s and Lightbridge 2 Air System’s firmware. Refer to DJI Assistant 2 (p. 30) for details. Upgrading the Remote Controller Firmware The System Status bar in Camera View of the DJI GO app will flash several times if a firmware upgrade is available. Follow these steps to upgrade the firmware via the DJI GO app. 1.
MATRICE 600 PRO User Manual b. Insert the Micro SD card into your PC. Extract all the downloaded files into the root directory of the Micro SD card. While the Matrice 600 Pro is powered off, remove the Micro SD card from your PC and insert it into the Micro SD card slot on the gimbal. Step 3- Upgrade the Firmware a. Ensure the remote controller is powered off and then power on one of the Intelligent Flight Batteries.
MATRICE 600 PRO User Manual If the LED is solid yellow after calibration, a problem has occurred. Ensure that the servos are mounted correctly and then try again. Avoid obstructions during calibration. If the landing gear was obstructed, recalibration will be required, per the above steps. If the “R” and “L” servo cables are reversed, travel will not be measured correctly. Fix the connections and recalibrate the landing gear using the above steps. Landing gear servo travel has been pre-calibrated.
MATRICE 600 PRO User Manual Reserved Mounting Position Dimensions A mounting position for your own devices is reserved at the bottom of the center frame. 1. Remove the twelve M3×6.5 screws at the bottom of the center frame first, and then remove the expansion mounting kit. M3×6.5 Screws Expansion Mounting Kit 2. The dimensions of the reserved mounting position is shown as follows (unit: mm). 149.1 3×M3 Thread depth 4 mm 258.3 Ф38 120° © 2016 DJI All Rights Reserved.
MATRICE 600 PRO User Manual A3 Pro Flight Control System Overview [3] [4] [1] [5] [2] [6] [9] [10] [7] [8] [11] [12] [13] [14] [15] Flight Controller [1] IMU1 Communicates with the IMU Pro module. Connected before delivery. [2] CAN1 Dedicated DJI CAN-Bus port. Communicates with the GPS-Compass Pro module or other DJI devices (e.g. Real Time Kinematic (RTK) GPS system, gimbals). [3] Orientation Arrow Points to the front of the aircraft.
MATRICE 600 PRO User Manual PMU Module [1] Power Port (9V 3A) [3] Provides power to the flight controller. Connected before delivery. [2] iBAT [1] Communicates with the DJI Intelligent Flight Battery. Connected to the battery management system before delivery. [3] 3S-12S [2] Draws power from the DJI Intelligent Flight Battery or other LiPo battery. Connected to the battery management system before delivery.
MATRICE 600 PRO User Manual Lightbridge 2 Air System Overview [8] [1] [2] [9] [7] [6] [5] [4] [3] [1] HDMI IN Supports up to 1080p60 input resolution. This port has been connected to an HDMI cable and the other end of the cable is an HDMI-D connector. [2] AV IN Receives AV input from the camera. [3] Gimbal Port Connects to a DJI gimbal or camera. [4] DBUS Port Sends the remote controller signal to the flight controller. Connected to the RF port on the flight controller upon delivery.
MATRICE 600 PRO User Manual DJI Gimbal Connection Illustrator Ronin-MX Lightbridge 2 Air System A3 Flight Controller CAN1* CAN1* HDMI CAN PWR AV HDMI SRW-60G Receiver FPV Camera SRW-60G Transmitter Ronin-MX When using the Ronin-MX, set the App Output Mode in the DJI GO app to display the image on your mobile device from the camera used with the Ronin-MX.
MATRICE 600 PRO User Manual Zenmuse X3, X5 Series and XT Lightbridge 2 Air System A3 Flight Controller CAN1* GIMBAL HDMI AV Gimbal Mounting Plate FPV Camera OR Zenmuse Z15 Series HD Gimbal Lightbridge 2 Air System A3 Flight Controller CAN1* GIMBAL HDMI AV OR G7 Z15 Series GCU FPV Camera *You can connect the CAN cable to the CAN Hub on the GPS cable.
MATRICE 600 PRO User Manual DJI Zenmuse X3 Gimbal and Camera Camera Camera Profile The X3 gimbal and camera can record up to 4K 4096×2160p video at 24 fps, and capture 12-megapixel images. It features a 1/2.3” Sony EXMOR CMOS image sensor. Preview of the camera’s POV in the DJI GO app before shooting images and video. Have extra options to shoot stills in burst mode or self-timer mode, and export video in either MOV or MP4 format.
MATRICE 600 PRO User Manual Gimbal Gimbal Profile The 3-axis gimbal provides a steady platform for the camera, allowing you to capture stable video and images. The gimbal can tilt the camera up to 120 degrees and rotate 320 degrees. +30° 0° -320° -90° +320° Under the default settings, turn the gimbal dial on the remote controller to tilt the camera. Note that you cannot simultaneously tilt and pan the camera in the Single Remote Controller mode.
MATRICE 600 PRO User Manual Press the C1 or C2 button to switch between pitch mode and yaw mode. Use the gimbal dial to control the tilt/pan motion of the camera. Using the DJI GO App to Control the Gimbal Follow the steps below to use the DJI GO app to control the gimbal’s pitch/yaw motion: 1. Go to the DJI GO app > Camera View. 2. Tap and hold on the screen until a blue circle appears. 3. Move your finger to control the gimbal’s pitch/yaw motion. Ready to Go（GPS） 09:29 P-GPS 12 61% AE D 210 M H H.
MATRICE 600 PRO User Manual Follow Mode The gimbal’s orientation is aligned with the aircraft’s nose. One user alone can control the pitch motion of the gimbal, but a second operator is required to control the yaw motion using a second remote controller. FPV Mode The gimbal will lock to the movement of the aircraft to provide a FirstPerson-View flying experience. Free Mode The gimbal’s motion is independent of the aircraft’s orientation.
MATRICE 600 PRO User Manual CMOS Sony EXMOR 1/2.3” 20 mm (35 mm format equivalent), f/2.8, focus at ∞ Lens 9 elements in 9 groups Anti-distortion Single shot Still Photography Modes Burst mode: 3/5/7 frames Auto Exposure Bracketing (AEB): 3/5 frames at ±0.
This content is subject to change. Download the latest version from http://www.dji.com/matrice600-pro If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. MATRICETM is a trademark of DJI. Copyright © 2016 DJI All Rights Reserved.
