N1 Video Encoder User Manual V1.0 2015.
Disclaimer Thank you for purchasing the N1 Video Encoder. Users must comply with local radio transmission laws and regulations when using this product. By using this product, you hereby agree to this disclaimer and signify that you understand all points completely. Please use this product in strict accordance with the manual and be sure to pay attention to the warnings. When assembling and using this product, follow all instructions carefully. SZ DJI TECHNOLOGY CO., LTD.
Product Profile The N1 Video Encoder is intended for the DJI Matrice 100 (abbreviated as M100) and DJI N1 Flight Controller, for which it offers video signal transmission and firmware upgrade capabilities if you are not using the Zenmuse X3 Gimbal with Camera as your recording device. The AV or HDMI port on the encoder receives video input from the non-DJI camera to generate a live HD video feed in the DJI GO app.
N1 Video Encoder User Manual You will require a 2.0mm hex key and foam tape to install the N1 Video Encoder onto the M100. If you are using HDMI IN, prepare an HDMI cable. If you are using AV IN, prepare a soldering iron, some solder and heat shrink tubing for wiring. Installation 1. Remove the two screws (M3x8 self-tapping) on the Aircraft Status Indicator, and then detach it from the upper plate gently to avoid damaging the cable. Handle the indicator cable gently Aircraft Status Indicator 2.
N1 Video Encoder User Manual 3. Connect one end of the N1 Video Encoder’s video and power cables to their corresponding 10-pin or 8-pin port on the N1 Flight Controller. Flight Controller 10-pin Port 8-pin Port 4. Place the other end of the power and video cables near the mounting position of the N1 Video Encoder. 5. Re-mount the upper plate of the center frame, and tighten the 16 screws (M2.5x5). Orientate the upper plate so that the notch faces the left of the aircraft (with its tail facing you).
N1 Video Encoder User Manual 7. Connect the other end of the power and video cables to the power and video ports of the N1 Video Encoder. Power IN Video OUT The N1 Video Encoder only supports the DJI N1 Flight Controller. Please strictly follow the steps above to supply power to the device. 8. Use foam tape to mount the N1 Video Encoder to the expansion bay, gimbal mounting plate or other flat surfaces. Usage Video Encoding 1. Turn on the remote controller and then the Intelligent Flight Battery.
N1 Video Encoder User Manual 3. Upgrade the Aircraft 1) Ensure the remote controller is powered off, and then power on the aircraft. The firmware upgrade will begin automatically once the aircraft is powered on. 2) The Status LED will blink red and green alternatively to indicate that the upgrade is in progress. It will take approximately 12 minutes to complete the firmware upgrade. 3) The Status LED will blink green if the upgrade is successful, at which point you should restart the aircraft.
N1 Video Encoder User Manual Supported Video Inputs Source Video Formats AV PAL, NTSC HDMI 720p50, 720p60, 1080i50, 1080i60, 1080p25, 1080p30, 1080p50, 1080p60 Specificaitions Dimensions 65.2 mm × 45 mm × 10.7 mm Weight 31.4 g Operating Temperature -10° to 40° C Pinout Diagrams AV Port [1] GND 1 [2] AV IN 2 3 [3] GND Reserved Port [1] IO (RX) [5] 12V 1 [2] IO (TX) [6] GND 3 [3] GND [7] IO (TX) 5 [4] 12V [8] IO (RX) 8 © 2015 DJI. All Rights Reserved.
This content is subject to change. Download the latest version from https://developer.dji.com/matrice-100 If you have any questions about this document, please contact DJI by sending a message to DocSupport@dji.com. © 2015 DJI. All Rights Reserved.