Quick Start

ManualsBrandsDJI ManualsQuadrocopter, MulticopterWhite Edition Quadcopter RtF Camera drone

Return-to-Home

Specifications

●

Supported File Systems FAT32 (≤ 32 GB), exFAT (> 32 GB)

Photo Formats JPEG, DNG (RAW)

Video Formats MP4/MOV (MPEG-4 AVC/H.264)

; Max capacity of 64GB

●

Operating Frequency 922.7 MHz-927.7 MHz (Japan only); 5.725 GHz-5.825 GHz; 2.400 GHz-2.483 GHz

●

Net Weight 570 g

●

Net Weight 670 g

4.14 in

2.80 in

●

Calibrating the Compass

Only calibrate the compass when the DJI GO app or the status indicator prompt you to do so. Observe the following rules

O NOT calibrate your compass where there is a chance of strong magnetic interference, such as magnetite, parking

DO NOT carry ferromagnetic materials with you during calibration such as cellular phones.

The DJI GO app will prompt you to resolve the compass issue if the compass is affected by strong interference after

12.44 in

●

Positioning Systems (P-Mode)

The aircraft uses GPS and a Vision Positioning System (VPS)

advised to fly in P-Mode which, depending on the GPS

GPS and VPS are used for positioning. The aircraft

GPS and VPS are not available. The aircraft can

●

Return-to-Home

It is important to take off with a strong GPS signal

DO NOT FLY

Refer to the Safety Guidelines and

DO NOT FLY

No Fly Zones

DO MONITOR YOUR ALTITUDE

DO MAINTAIN LINE OF SIGHT

●

The Inspire 1 Pro’s compass and GPS will not work in Polar Regions. The aircraft will auto switch to ATTI Mode and use the VPS for positioning.

Vision Positioning

Effective Altitude:

≤ 9.8 feet

GPS Positioning

INSPIRE 1

PRO

11. Gimbal Dial

19. CAN Bus Port

Through the DJI GO app, the camera focus, shutter speed, aperture and ISO can be manually adjusted. The DJI Focus,

Positioning System (VPS) gives it the power to hover in position at low altitudes even without GPS. Like all DJI flight

displayed in the DJI GO app. Dual remote controller mode makes it possible for the aircraft and camera to be operated

* *

INSPIRE 1 PRO Remote Controller

Folded

Gear Up Gear Down

1. Gimbal and Camera

2. Gimbal Lock

Fly Safe

Quick Start Guide

V1.2

Summary of content (10 pages)

PAGE 1
INSPIRE 1 Quick Start Guide V1.
PAGE 2
INSPIRE 1 PRO The Inspire 1 Pro features the Zenmuse X5 gimbal and camera equipped with a 15mm f/1.7 (35mm format equivalent 30mm) Micro Four Thirds interchangeable lens. It shoots sharp 16MP stills and stable video at up to 4K. The aircraft’s retractable landing gear pulls up out of view, giving the camera an unobstructed 360 degree view of the world below. Through the DJI GO app, the camera focus, shutter speed, aperture and ISO can be manually adjusted.
PAGE 3
Remote Controller The maximum transmission distance of the Inspire 1 Pro remote controller is 16,400 feet (5 km)*. The built-in LiPo battery powers the device for up to four hours in between charges. An ergonomic design puts photo and video capturing, playback and gimbal control functions within comfortable reach, crucial when the aircraft is being operated.
PAGE 4
Fly Safe DJI encourages you to enjoy flying in a safe, responsible and smart way. 400 ft Always fly under DO MONITOR YOUR ALTITUDE DO NOT FLY near or above people, near trees, power lines or buildings. and fly under 400 feet (120 meters). It is important to understand basic flight guidelines for the safety of both you and those around you. Refer to the Safety Guidelines and Disclaimer for more information.
PAGE 5
Specifications ● Aircraft (Model: T600) Weight 2870 g (Battery and propellers included, Zenmuse X5 excluded) 3400 g (Battery, propellers and Zenmuse X5 included) Max Takeoff Weight 3500 g Max Tilt Angle 35° Max Ascent Speed 5 m/s Max Descent Speed 4 m/s Max Speed 18 m/s (ATTI mode, no wind) Max Service Ceiling Above Sea Level 14,700 feet (4,500 meters) (Software altitude limit: 400 feet above takeoff point) Max Flight Time Approx. 15 minutes Operating Temperature 14° to 104° F (-10° to 40° C) 1 7.
PAGE 6
Using INSPIRE 1 PRO 2. Watch the Tutorial Videos 1. Download the DJI GO App Search ‘DJI GO’ on the App Store or Google Play and download the app to your mobile device. Watch the tutorial videos at www.dji.com or in the DJI GO app. DJI GO app ● Tutorial Videos DJI GO supports iOS 8.0 (or later) or Android 4.1.2 (or later). 3. Check the Battery Levels High Press once to check the battery level. ● Press once, again and hold to turn on/off. ● Low High Low 4.
PAGE 7
6. Prepare the Remote Controller Unfold the mobile device holder and the antennas. Strong Weak Try to keep the aircraft inside the optimal transmission range. If the signal is weak, adjust the antennas or fly the aircraft closer. Unfold Optimal Transmission Range 2 Press the button to release the clamp. ● Place your mobile device and adjust the clamp to secure. On the Master RC, launch the DJI GO app and enter Camera View. Tap on the top of your screen to bring up the RC Settings.
PAGE 8
. Mount the Gimbal and Camera Ke y 2 4 3 Slot 1 Align the white lines and insert the gimbal. Align the key on the damping plate with the slot on the gimbal. Rotate the Gimbal Lock to the unlocked position. ● Be sure to remove the gimbal before transforming the aircraft to Travel Mode. ● Always power off the aircraft before mounting or removing the gimbal. Rotate the Gimbal Lock to the locked position. 9. Preparing for Takeoff DJI GO App Toggle the Flight Mode Switch to the safest P-Mode.
PAGE 9
11. Flight Before taking off, ensure the Aircraft Status Bar in the DJI GO app indicates ‘Safe to Fly (GPS)’. Safe to Fly (GPS) In the DJI GO App: Auto Takeoff The aircraft will take off and hover at an altitude of 4 feet (1.2 meters). Auto Landing The aircraft will land vertically and stop its motors. ● Return-to-Home Brings the aircraft back to the Home Point. Tap again to stop the procedure.
PAGE 10
INSPIRE 1 Creativity Unleashed www.dji.