User manual
Table Of Contents
- Using This Manual
- Product Profile
- Flight Safety
- Aircraft
- Remote Controller
- Starting and Activating the Remote Controller
- Remote Controller Overview
- Mounting the WB37 Intelligent Battery
- Mounting the Dongle
- Mounting the Strap and Bracket Kit
- Adjusting the Antennas
- IP Rating
- User Interface
- Video Transmission
- Remote Controller LEDs and Alert
- Charging the Remote Controller and Checking the Battery Level
- Linking the Remote Controller and Control Stick Modes
- Buttons Overview
- Flight Mode Switch (N/S/F)
- Calibrating the Compass
- HDMI Settings
- Advanced Dual Operator Mode
- Intelligent Battery Station
- Intelligent Flight Battery
- DJI Pilot 2 App
- Firmware Update
- Appendix
30
©
2022 DJI All Rights Reserved.
MATRICE 30 SERIES User Manual
DJI AirSense
Airplanes with an ADS-B transceiver will actively broadcast ight information including locations, ight
paths, speeds, and altitudes. DJI aircraft incorporated with the DJI AirSense technology are capable
of receiving flight information broadcast from ADS-B transceivers that comply with 1090ES or UAT
standards within a radius range of 10 kilometers. Based on the received ight information, DJI AirSense
can analyze and obtain the location, altitude, orientation, and velocity of the surrounding manned
airplanes, and compare such gures with the current position, altitude, orientation, and velocity of the
DJI aircraft to calculate in real time the potential risk of collision with the surrounding manned airplanes.
DJI AirSense will then display a warning message in DJI Pilot 2 according to the risk level.
DJI AirSense only issues warning messages on approaches by specic manned airplanes under special
circumstances. Always fly the aircraft within your visual line of sight and be cautious at all times to
ensure ight safety. Please be aware that DJI AirSense has the following limitations:
1. DJI AirSense can only receive messages sent by airplanes installed with an ADS-B Out device that is
in compliance with 1090ES (RTCA DO-260) or UAT (RTCA DO-282) standards. DJI devices cannot
receive broadcast messages from or display warnings on airplanes not equipped with properly
functioning ADS-B Out devices.
2. If there is an obstacle between a manned aircraft and a DJI aircraft, DJI AirSense will not be able
to receive ADS-B messages from the aircraft or send warnings to the user. Keenly observe your
surroundings and y with caution.
3. Warning prompts may be sent with delay if DJI AirSense experiences any interference from the
surrounding environment. Keenly observe your surroundings and y with caution.
4. Warning prompts may not be received if the DJI aircraft is unable to obtain information on its own
location.
5. DJI AirSense cannot receive ADS-B messages from manned airplanes or send warnings to the user
when it is disabled or miscongured.
When a risk is detected by the DJI AirSense system, the AR projection display will appear on the current
view in DJI Pilot 2, intuitively showing the distance between the DJI aircraft and the airplane, and issuing
a warning alert. Users should follow the instructions in DJI Pilot 2 upon receiving the alert.
a.
Notice:
A blue airplane icon will appear on the map.
b.
Caution:
The app will display the message: “Manned aircraft detected nearby. Fly with caution.”
A small orange square icon with the distance information will appear on the camera view, and an
orange airplane icon will appear on the map view.
c.
Warning:
The app will display the message: “Collision risk. Descend or ascend immediately.” If the
user is not operating, the app will display: "Collision risk. Fly with caution.” A small red square icon
with the distance information will appear on the camera view, and a red airplane icon will appear on
the map view. The remote controller will vibrate to alert.