SP-VDP-400 Digital Video Recorder USER’S MANUAL
WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
IMPORTANT SAFEGUARDS 1. Read Instructions 13. Damage requiring Service All the safety and operating instructions should be read before the The manufacturer as such additions may result in the risk of fire, Unplug this equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power-supply cord or the plug has been damaged. B. If liquid is spilled, or objects have fallen into the equipment. C.
INDEX ---------------------------------------------- 6 ------------------------------------------------- 6 --------------------------------------------------------- 6 ---------------------------------------------- 7 ----------------------------------------------------------- 8 --------------------------------------------------------- 8 ----------------------------------------------- 9 ---------------------------------------------- 10 3.
INDEX ----------------------------------------------------- 30 ------------------------------------------------------- 30 ----------------------------------------------------------- 31 ---------------------------------------------------------- 32 ----------------------------------------------------- 33 -------------------------------------------------- 34 ------------------------------------------------------- 35 5.3.1 MOTION ------------------------------------------------------- 35 5.3.
INDEX 6. SEARCH ------------------------------------------------------------- 54 ------------------------------------------------------- 55 6.1.1 Search Menu -------------------------------------------------- 56 6.1.2 Calendar Search -------------------------------------------------- 56 6.1.3 Event Search -------------------------------------------------- 57 6.1.
1. SAFETY CAUTIONS ※ Follow these instructions to keep the user safe and prevent property damage. Read them carefully before the use of the product. The responsibility falls on the user to install and use the product properly. 1.1 Power Source-related 1.2 Installation-related ① Insert the power plug fully and firmly into the power source. - Unstable connection may cause fire. ① Do not place candlelight or cigarette light on top of the product or do not install the product near heating devices.
1.3 Cleaning and Usage-related ⑥ When cleaning the product, unplug the power cord and gently wipe using a soft cloth. Do not directly spray water on the product or do not use benzene, thinner or alcohol when cleaning. ① Un p lu g the p o wer p l ug du rin g li ghtn in g , thunderstorm or when not in use for long periods of time. - It may cause electric shock or fire. - It may cause electric shock or fire.
2. OUTLINE 2.1 Functions This DVR provide superior video image quality on Live view and Playback. • Pentaplex Operation Performance (Live, Recording, Playback, Backup, Network) • Up to maximum 16 channel composite input ports depending on model. • Various Recording mode. (Manual / Schedule / Event) • Various Search functions. (Date/Hour search, Calendar search, Event Search) • Various Playback functions.
2.
3. DVR ORGANIZATION 3.
※ Front Button The front panel of DVR is similar as normal VCR or Multiplexer and the functions are also similar . Front buttons have various functions and are used for DVR initial setting and others. Please refer to the below explanation. NUMBER buttons (1 ~ 0) Displayed selected camera number to full screen. And also these buttons are used to enter a password. FUNCTION button Select function in PTZ operation mode. LIVE button Change mode from search or playback mode to live mode.
PTZ button Enter PTZ mode. SMART button Start smart search function. REPLAY button Start playback function. Direction Buttons (▲, ▼, ◀, ▶ ) This buttons are used when move to other menu or change the position of the CAMEO screen. In PTZ mode, it is used PAN/TILT function. ▲ : In Playback mode, it is Panorama search function button. In PTZ mode, it is used to move the camera to up. ▼ : In Playback mode, it is Smart search function button. In PTZ mode, it is used to move the camera to down.
3.
3.3 Remote Controller ID NUMBER MUTE OSD ON/OFF UP Direction Key LEFT Direction Key RIGHT Direction Key DOWN Direction Key ENTER ESC MENU BACKUP SETUP STATUS DISPLAY FREEZE SQEUENCE PTZ ZOOM PANIC RECORDING PLAYBACK CONTROL ALARM SETUP SPOT SETUP ※ How to set ID ① Before setup the ID, Enter to the GENERAL SETUP and set the ID first. (Default is 0) ② While pressing and holding the ID button, enter the unit address of the DVR by two-digit.
4. LIVE 4.1 Live Screen Execution Information Message Camera Name Record Status Icon Live Screen PTZ Control Information Screen Expand/Reduction Window Backup Progress Status(%) Current Date and Time Current Channel Information Icon Current Event Information Icon Sequence Icon - Record Icon (Red) When record in live screen. - Video-loss Icon When there is no video input. - Time Icon When record by designated time. - Audio Icon When sound is generated in live mode.
4.1.1 Top Menu In live screen, if ▲ button of the remote controller or front panel is pressed, or if the mouse cursor is placed over the end of the top area, the top menu is appeared. 4.1.2 Bottom Menu In Live screen, if ▼ button of the remote controller or front panel is pressed, or if the mouse cursor is placed over the end of the bottom area, the bottom menu is appeared.
4.1.3 CAMEO Menu In live screen, if the ENTER button of the remote controller or front panel is pressed, a blue square cursor will be appeared. If the ENTER button is pressed again, the CAMERA menu will be appeared. ▪ CAMEO CHANGE : The live camera can be changed to the selected channel. If the camera number is selected at the pop-up menu shown below, the camera is changed to the selected channel. ▪ FREEZE : Live screen of the selected channel can be paused.
▪ PTZ : PTZ Camera should be installed otherwise the PTZ menu is not activated. The following picture will be appeared when select PTZ menu. ※ Using Mouse : On the above menu, when click the right button of mouse, the control screen for Menu, Zoom, Focus and Iris will be appeared. Zoom Focus Iris ※ Using Remote Controller or Front Key : The below Hot Key is available. - Press the ENTER button on PTZ Camera channel. - Press the ENTER button again then the CAMEO menu will be appeared.
- SPEED SETUP : Set the PTZ camera speed. ( 1 to 8) NOTE: If the mouse is used to move the PTZ camera, the movement speed depends on the position of the mouse. As the mouse pointer moves away from the center, speed becomes faster. - PRESET SETUP : Set the preset position. If the position setup is saved, PTZ camera will be directed to the set position by preset number. - PRESET TOUR : 6 different preset list can be created. If the created preset lists are set to “ON”, recording is made with preset tour.
5. SETUP In this category, there are SYSTEM, NETWORK, DEVICE, RECORD and EVENT. On the Top menu, select the [SETUP] menu icon. After select the icon, the following LOGIN window will be appeared. Enter the password by the key buttons and press the OK button. (The default password : 1) 5.1 SYSTEM SETUP In this category, there are General, Alarm, Disk, Monitor, Account, Configuration and Shutdown. Select the [SYSTEM] menu.
5.1.1 GENERAL [SYSTEM] ▪ LANGUAGE : Select the language. (English, Germany, French, Spanish, Japanese, Chinese, Italian, Russian, Dutch and Korean) ▪ KEY TONE : Turn on/off the buzzer sound of key. ▪ UNIT ADDRESS : Set the DVR ID. This ID can be used when use multi DVR in same place by one remote controller. ▪ BASE CAMERA NO. : Set the beginning number of camera. If set this value to 17, the camera number start with 17. ▪ MENU TIMEOUT : Keep the Menu screen for this value then escape from Menu.
5.1.1 GENERAL [DATE / TIME] ▪ DATE FROMAT : Select the data format. (YY/MM/DD) / (MM/DD/YY) / (DD/MM/YY) ▪ TIMEZONE : Select the timezone and DST. The city which don’t use DST is set to [OFF] automatically. ▪ DATE DISPLAY : Display date on live screen or not. ▪ DATE / TIME : Change date and time. ▪ NTP : Select the usage of NTP setting. DVR time is synchronized with NTP server and get the standard time. The default server is [pool.ntp.org] and User can input other server.
5.1.2 ALARM OUT ▪ SIGNAL : Select on/off to use alarm by channel. ▪ ALARM SET TEST : Check the alarm connection whether it works properly or not. Press the [SET] button then alarm device will be operated. ▪ ALARM CLEAR TEST : Press the [CLEAR] button then alarm device will not be operated. 5.1.3 DISK ※ NOTE : When install HDD first time, after install HDD, should format by the [INSTALL] button. [INSTALL] - Display initial HDD install and information.
[CHECK / USB] ▪ RECORD START TIME : Display the earliest recorded data information. ▪ RECORD END TIME : Display the latest recorded data information. ▪ DISK CHECK : Check the data from the earliest recorded to the latest recorded. ▪ USB RESET : Reset the USB connection. ▪ USB FORMAT : Format the connected USB.
5.1.4 MONITOR ▪ HDMI : Select the resolution for connected monitor. ▪ FILTER : ▪ BORDER COLOR : Change the border color. ▪ ALPHA BLENDING : Set the transparency of menu. (Set 1 to 20 and 20 is closer to the more transparent.
5.1.5 ACCOUNT ※ Add / delete any user and give permission freely. ※ When add new user, have to input new password. When delete user, confirm again. NOTE: ( Default ADMIN password is 1), Initial user name can be modified but can not delete. CAUTION: Default Admin account must not be deleted before add new user. If delete default Admin user before add new Admin user, can not access on [SETUP] menu. ※ By the [PERM] menu, can give permission to each ID.
5.1.6 CONFIG ▪ SLOT : Select the slot to load or save on DVR memory. ※ DEFAULT : Change factory default setting. ▪ DATE : Display the latest saved date. ▪ LOAD : Load the saved data. ▪ SAVE : Save the set data. ▪ DEL : Delete the saved data on Slot. ▪ EXPORT : Export the set data to USB or DVD. ▪ IMPORT : Import the set data to USB or DVD.
5.1.7 SHUTDOWN ▪ RESTART : Restart the DVR. ▪ SHUTDOWN : Shutdown the DVR.
5.2 DEVICE SETUP In this category, there are Camera, PTZ, Spot, Sequence and Private Zone setting. Select the [DEVICE] Menu. 5.2.1 CAMERA ▪ CAMERA LABEL : Select the camera label of live screen. (ALL / NUMBER / NAME / OFF) ▪ NAME : Change the camera name. ( If select the camera name, the virtual keyboard will be appeared.) ▪ INSTALL : Select On/Off button to use camera. ▪ HIDDEN : Select On/Off button to hide camera on live view. ( Record works correctly.
If select the camera name, the virtual keyboard will be appeared. Max camera name should be less than 11 character. [Virtual Keyboard] 5.2.2 PTZ [PTZ] ▪ PORT : Select the Baud Rate for using PTZ camera. ▪ ADDRESS : Select the ID for using PTZ camera. ▪ PROTOCOL : Show the PTZ protocol list. NOTE : baud rate, data bit, parity, stop bit, ID and protocol depend on PTZ camera for using. CAUTION : When connect the camera on the RS-485 port, refer to the manual of camera manufacturer.
5.2.3 SPOT CAMERA : Select the camera for display on spot monitor. DEFAULT : Select the camera for display on spot monitor when sequence is off. SEQUENCE : Select On/Off for sequence screen. DWELL : Select the interval time to move next channel. The max value is 256 sec. POPUP : Select On/Off for pop-up screen when event is occurred. * Exception : SVM-2004HDL dose not support SPOT.
5.2.4 SEQUENCE PAGE DWELL TIME : Select the dwell time to move next channel. CAMEO DWELL TIME : Select the dwell time for CAMEO sequence. NOTE: CAMEO sequence means selected camera is rotated in select cameo of division screen. Camera image which is shown on the other CAMEO of division screen is not included in CAMEO sequence.
5.2.5 PRIVATE ZONE ▪ ZONE ENABLE : Select On/Off to use. (LIVE mode/ SEARCH mode) ▪ ZONE COLOR : Select the color to hide. ▪ ZONE : Select the zone to hide. (When select the ZONE button, the camera image will be appeared. NOTE : Move the blue dot to a desired location and press the OK button. Drag and move it to include the desired area and press the OK button.
5.3 EVENT SETUP In this menu, there are Motion, Alarm in, Video Loss, System and Display setup. Select the [EVENT] menu. 5.3.1 MOTION [INPUT] ▪ ACTIVE : Select On/Off to activate motion. ▪ LEVEL : Select the sensitive for motion trigger. (Select 1 to 5 level) ▪ AREA : Select the motion area. TIP: If select the ACTIVE+ / LEVEL+ / AREA+ menu, can change all setting at once.
▪ AREA SETUP In the Area setup, the Red square is shown at the top left side of the screen. If select the OK button, the dot color will be changed to Green. A motion area can be selected by the direction buttons. NOTE : When the status is Red square, can move any direction to select. When the status is Green color, can select motion area or cancel the set area. After set the motion area, if select the MENU button, the following screen will be appeared. ▪ SELECT ALL : Select all motion area.
[ACTION] ▪ RECORD : Select the channel for record. ▪ ALARM : Select On/Off for alarm. ▪ BUZZER : Select On/Off for buzzer. ▪ PRESET : Set the preset number. (When motion is triggered, the PTZ camera move to the set preset number position) ▪ E-MAIL : Select On/Off for e-mail notification. TIP: If select to the [DEFAULT], only record the channel which is occurred event.
5.3.2 ALARM IN TIP: If select the ACTIVE+ / TYPE+ menu, can change all setting at once. [INPUT] ▪ ACTIVE : Select On/Off to activate alarm. ▪ NAME : Type any name. ▪ TYPE : Select the alarm type. (NO : Normal Open / NC : Normal Close) [ACTION] ▪ RECORD : Select the channel for record. ▪ ALARM : Select On/Off for alarm. ▪ BUZZER : Select On/Off for buzzer. ▪ PRESET : Set the preset number.
5.3.3 VIDEO LOSS TIP: If select the ACTIVE+ menu, can change all setting at once. [INPUT] ▪ ACTIVE : Select On/Off to activate. [ACTION] ▪ RECORD : Select On/Off for record. ▪ ALARM : Select On/Off for alarm. ▪ BUZZER : Select On/Off for buzzer. ▪ PRESET : Set the preset number. (When motion is triggered, the PTZ camera move to the set preset number position) ▪ E-MAIL : Select On/Off for e-mail notification.
5.3.4 SYSTEM [WARNING] ▪ CHECK INTERVAL : Select the check interval. (Select 1 hour to 24 hour) ▪ DISK WARNING : Select how to give a warning if disk error. (OFF, POPUP, POPUP + BUZZER) ▪ THRESHOLD : Critical value for Warning ▪ CURRENT TEMP. : Current temperature of the system [DISK] ▪ DISK FULL WARNING : Select ON/OFF to disk full warning. ▪ USED SPACE : Display the used space ▪ ALARM : Select the channel for alarm out. ▪ BUZZER : Select On/Off for buzzer. ▪ MESSAGE : Select On/Off for message.
[E-MAIL] – Select option On/Off for e-mail notification. ▪ POWER / MENU / LOGIN FAIL / DISK FULL / LOG IN / SMART 5.3.5 DISPLAY ▪ DISPLAY : Select display time by second. (Select 0 to 100) ▪ EVENT MESSAGE : Select On/Off to display event message. ▪ EVENT POPUP : Select On/Off to pop-up.
5.4 RECORD SETUP Select the [RECORD] menu. In this menu, there are Setup, Record, Pre/Post, Audio, Panic Setup 5.4.1 SETUP & RECORD ▪ SETUP MODE : Select the record schedule. (CONTINUOUS / SCHEDULE) [CONTINUOUS] ▪ DAY TIME : Select the day time. (The night time is changed automatically according to the day time zone) ▪ WEEKEND : Set the weekend zone. [DAY] / [NIGHT] / [WEEKEND] ▪ TIME : Set the recording frame and resolution by channel. ▪ EVENT : Set the event recording.
[SCHEDULE] ▪ Set 3 different recording setup by day and time. (SET1, SET2, SET3) This is related with [RECORD] menu so [CUSTOM] mode should be matched with [RECORD] menu. TIP : For SET1, SET2, SET3 recording, change the setting [SETUP MODE] to [CONTINUOUS] and enter to the [RECORD] menu then change the setting. [SCHEDULE selected screen] If set to [CONTINUOUS] in [SCHEDULE] menu, the DAY / NIGHT / WEEKEND menu will be changed to SET1 / SET2 / SET3. Also set the frame and resolution.
5.4.2 EVENT PRE / POST ▪ PRE RECORD : Sets Pre-event recording time ( Max 60 second ) ▪ POST RECORD : Sets Post-event recording time ( Max 100 second ) 5.4.3 AUDIO ▪ RECORD : Select On/Off for audio recording by channel. TIP: If select the RECORD+ menu, can change all setting at once.
5.4.4 PANIC ▪ FPS : Select the recording frame by each channel. ▪ Quality : Select the resolution by each channel. ▪ AUDIO : Select On/Off for audio recording by each channel.
5.5 NETWORK SETUP In this menu, there are Network, Serial, DDNS, E-mail setup. Select the [NETWORK] menu. 5.5.1 LAN [SERVER] ▪ DHCP : Select On/Off for dynamic IP. If Dynamic IP is OFF, DVR get IP address from router automatically. ▪ HOST NAME : Type any Host name. ▪ IP ADDRESS : Type IP address. (Available when DYNAMIC IP is OFF) ▪ NETMASK: Type Subnet mask. (Available when DYNAMIC IP is OFF) ▪ GATEWAY : Type Gateway. (Available when DYNAMIC IP is OFF) ▪ DNS SERVER : Type DNS server.
[SERVER2] ▪ DHCP : Select On/Off for dynamic IP. ▪ IP ADDRESS : Type IP address. (Available when DYNAMIC IP is OFF) ▪ NETMASK : Type Subnet mask. (Available when DYNAMIC IP is OFF) [CLIENT] ▪ CLIENT ACCESS : Select client access options. ( ALL / RANGE ) ▪ BEGIN ADDRESS / END ADDRESS (When select RANGE option, type the IP address to accept) : Input the acceptable IP address. ▪ SMS / WEB PORT (TCP) : Select SMS / Web Port. ▪ REMOTE RESTART : Select On/Off to restart DVR at remote.
5.5.2 SERIAL [RS-232 INPUT SETUP] ▪ SERIAL TYPE : Select external device. ▪ MODEL : Select the protocol to use. ▪ PORT : Select the Baud Rate / DATA bit / Parity / Stop Bit. [RS-485 INPUT SETUP] ▪ SERIAL TYPE : Select external device. ▪ MODEL : Select the protocol to use. ▪ PORT : Select the Baud Rate / DATA bit / Parity / Stop Bit.
5.5.3 DDNS ▪ DDNS SERVER : Select DDNS server. ( ezddns.com / dyndns.com / changeip.com ) ▪ HOST NAME : Input the host name from the registered on DDNS server. ▪ USER NAME : Input the user name from the registered on DDNS server. ▪ PASSWORD : Input the password from the registered on DDNS server. ▪ ROUTHER IP : Select On/Off for sending IP information to the DDNS server. If use any router, this setting should be [ON]. ▪ STATUS : Check the connection status.
5.5.4 E-MAIL [ADDRESS] ▪ SEND E-MAIL : Select On/Off for use. ▪ SCHEDULE : Set the usage time. (From : Start time / To : End time) ▪ E-MAIL ADDRESS : Input the E-mail address to receive. [SERVER] ▪ MAIL SERVER : Select the mail server. (SMTP server / DVR System) ▪ USER NAME : Input the user name. ▪ USER E-MAIL : Input the user e-mail address. ▪ SERVER ADDRESS : Input the server address. ▪ SERVER PORT : Input the server port. ▪ LOGIN ID : Input the Login ID. ▪ LOGIN PASSWORD : Input the Login password.
5.6 SYSTEM INFOMATION In this menu, there are System Log, Status, Version. On the Top menu, select the [INFORMATION] menu icon. 5.6.1 SYSTEM LOG ▪ Check the system log by the left, right direction button.
5.6.2 STATUS [DISK] ▪ Display HDD Status. ▪ CHECK SMART NOW : Check the smart. ▪ SMART INFORMATION : Show the smart information. [RECORD] ▪ Display RECORD Status.
[AUDIO] ▪ Display AUDIO Status.
5.6.3 VERSION ▪ Display DVR version and information.
6. SEARCH On the Top menu, select the [SEARCH] menu icon. After select the menu, the following Log-in window will be appeared. Enter the password by the key buttons and press the ENTER button. (The default password : 1) ▪ QUICK SEARCH : Designated time search by User ▪ CALENDAR : Search by date and time with Calendar. ▪ EVENT SERARCH : Search by event ▪ OVERLAPPED LIST : Search the overlapped data by changing time ▪ GO TO FIRST : Search with initial saved data.
6.1 Search Screen Execution Information Message Camera Name Search Information Icon Search Icon Search Screen Repeat Time Information Screen Expand/Reduction Window Backup Progress (%) Recorded Audio Information Icon Search Date/Time 6.1.1 Search Menu When mouse cursor is placed over on the bottom side, the Search menu is appeared.
6.1.2 CALENDAR SEARCH a. Select the data by the direction button. - Recorded data is displayed the orange color. b. Select the time by the direction button. - After select hour, minutes will be appeared. NOTE: The time graph color is different by the recording mode. Continuous Recording = Blue, Audio Recording = Light Blue, Event Recording = Red.
6.1.3 EVENT SEARCH ▪ DATA : Select Date to search. ▪ MOTION : Select On/Off event for search. ▪ ALARM IN : Select On/Off event for search. ▪ VIDEO LOSS : Select On/Off event for search. ▪ SELECT CAMERA : Select the camera for search. ▪ VIEW SEARCH LOG : Display selected event log. ▪ HOUR : Select time period to see. ▪ PREV : Display previous page. ▪ NEXT : Display next page. ▪ GOTO : Display the image by selected event.
6.1.4 OVERLAPPED LIST ▪ If user change the time or applied DST (Daylight Saving Time), there will be overlapped data. ▪ After select the list, if select the [PLAY] button, can search [QUICK SEARCH] or [EVENT SEARCH].
6.1.5 PANORAMA SEARCH ▪ During normal search, press the [PANORAMA] button. ▪ By mouse, click the right mouse button and click the [PANORAMA] Search. ▪ Playback with frame by frame. 6.1.6 SMART SEARCH ▪ During normal search, press the [SMART] button. ▪ Find only event and playback automatically without interval.
6.1.7 SECTION REPEAT SEARCH ▪ During normal search, press the [LOCK] button. When press one time, the start position is set, press one more time, the end position is set. ▪ By mouse, click the below red circle button. ▪ Only playback the set section repeatedly. ▪ In search screen, display the following mark.
※ Button Explanation in Search mode ▪ Remote Controller or Front button Button SEARCH ESC ENTER Explanation Display the [SEARCH] menu. Cancel the Search mode or return to the live screen. Select the CAMEO menu. FAST REVERSE When reverse play, up and down play speed. FAST FORWARD When forward play, up and down play speed. PAUSE Pause the playback. FORWARD PLAY Playback the data. REVEERSE PLAY Reverse Play the data. DISPLAY Display division screen.
7. BACKUP On the Top menu, select the [BACKUP] menu icon. After select the menu, the following Log-in window will be appeared. Enter the password by the key buttons and press the ENTER button. (The default password : 1) ▪ TARGET : Select the device to backup. (USB / DVD) ▪ FROM : Select the start date and time. ▪ TO : Select the end date and time. ▪ BACKUP TITLE : Type any title. ▪ SELECT CAMERA : Select the camera for backup ▪ EARLIEST RECORD : Display the earliest record.
7.1 Playback with backup data ▪ After backup, the DVR Player is copied with data. ▪ Backup data only can be played on DVR Player at PC. ▪ Can export to JPEG still shot.
8. APPENDIX 8.
8. APPENDIX 8.2 Trouble Shooting SYMPTOM No Power No camera image MEASURES If the power LED is not lighted, check the below items. - Check the power plug and outlet. (Refer to the [Cautions for safety] - Connect the power cord to the power connector of DVR properly. - Connect the camera cable to the DVR port properly. - Check the connected monitor cable with DVR. (Refer to the [Rear Panel Configuration]) - Check the camera power and lens setting.
Not work remote controller No sound in live view - Check the battery polarity. - Check the remote controller ID. (Refer to the [Remote Controller Configuration]) - Focus on the remote controller to the IR sensor. - Use the remote controller within 7 meters from DVR. - Change the battery. - Check the mike and audio cable with DVR port. (Refer to the [Real Panel Configuration]) - Check the speaker power which is connected on Audio port. - Turn on the Audio in the CAMEO menu.
