CHIPPER ASSEMBLY GUIDE MODEL: OPC503V 3 IN CHIPPER SHREDDER DETAIL K2 INC. DK2 POWER USA 4301 S Valley View Blvd STE 10-11 Las Vegas, NV 89103 1-702-331-5353 DETAIL K2, INC. 1080 Clay Avenue Unit 2 Burlington, Ontario, Canada L7L0A1 DK2 USA EAST 6245 Industrial Parkway Whitehouse, OH 43571 PARTS AND SERVICE 702-331-5353 OR WWW.DK2POWER.
STEP 1: Open and unpack all items. Leave lots of working space. Inspect all parts. The CHIPPER is shipped in a crate. Remove all sides before you begin. NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING PARTS PLEASE CALL DK2 POWER AT 702-331-5353 OR CONTACT US VIA OUR WEBSITE WWW.DK2POWER.
STEP 2: 1. INSTALL THE HANDLE 2.
STEP 3: 1. INSTALL THE CHIP CHUTE 2.
STEP 4: 1. 2. 3. 4. INSTALL THE TREE FEED CHUTE Remove the 4 nuts and hardware Be cautious NOT TO DROP them into the cutting chamber.
STEP 5: 1. INSTALL THE LEAF VAC HOSE 2. Remove the 3 nuts and hardware and the cover plate. 3. Keep the plate in case you will remove the hose in the future. 4. Install the hose plate and shown, replace the nuts and tighten.
STEP 6 1. 2. 3. 4. LEAF VAC HOSE STORAGE Wrap the hose OVER the chip chute as shown Wrap the hose across the front of the hopper Place the HOSE HANDLE across the push bar as shown and UNDER THE HOSE. 5. Let engine cool before you wrap your hose into storage position. Take care NOT to melt it on the muffler.
STEP 7 1. INSTALL THE TOW BAR TROLLEY COMBO 2. Remove the pin, insert the tow bar with wheel down, re-pin.
STEP 8 1. 2. 3. 4. TOW BAR TROLLEY COMBO Shown is trolley mode Remove Tow Bar and flip over for TOWING position. When tow bar is removed, to increase your work area when chipping, use the drop stand.
STEP 9 1. DROP STAND 2. Drop stand is up when trolley wheel is down. 3. Drop stand is up when tow bar is reversed for towing.
STEP 10 1. WHEEL LOCK FEATURE 2. REMEMBER TO RAISE YOUR DROP STAND AND TO UNLOCK YOUR WHEELS BEFORE TOWING 3. Wheel shown is in free wheeling position 4. Remove pin, slide wheel forward, re-pin wheel and axel together to keep wheel from rolling and LOCK. 5. BOTH WHEELS LOCK TO HOLD YOUR CHIPPER IN PLACE FROM ROLLING WHEN YOU ARE WORKING.
STEP 11 1. ENGINE 2. Change oil after first 5 hours of use on brand new engine 3. Fill oil full, your engine has a low oil shutoff and will not start if low on oil. This is a protection system for your engine. 4. See Engine manual for complete instructions. 5. TURN KEY ON 6. CHOKE IF NEEDED 7. TURN ON GAS- SLIDE LEVER ALL THE WAY TO THE RIGHT 8.
STEP 12 1. 2. 3. 4. 5. 6. SAFETY KIT AND TOOLS The white bottle is used for oil fill Work gloves, safety glasses, ear protection included. A 1 7/8 tow ball is included Manuals and assembly tools.
REV 1 – 9-19-2019
No. Specification No.2 1 M10*70 bolt 41 Specification3 M6locknut 2 hitch trailer 42 spring washer⌀6 3 washer⌀10.5*⌀22*2 43 washer⌀6.4*⌀12*1.6 4 spring washer⌀10 44 side chipper room 5 M10locknut 45 side chipper room cover 6 M8*45 bolt 46 M6*12 bolt 7 washer⌀8.4*⌀20*1.
READ THE KOHLER ENGINE MANUAL SUPPLIED WITH YOUR UNIT FOR FULL ENGINE OPERATION, SAFETY, AND MAINTENANCE. YOUR UNIT HAS A COMMERCIAL KOHLER ENGINE WITH A 3YR PARTS AND SERVICE WARRANTY. FOR WARRANTY IN YOUR AREA CONTACT THE NEAREST KOHLER DEALER. VISIT WWW.KOHLERENGINES.COM FOR PARTS, SERVICE, MANUALS, AND DEALER LOCATIONS.
OPERATION – BEFORE TURNING KEY AND PULL STARTING ENGINE CLEAR AREA OF ALL PEOPLE AND PROPERTY THAT COULD BE DAMAGED. THINK SAFETY. CHIPS ARE FLYING PROJECTILES AND CAN CAUSE INJURY. WEAR SAFETY GLASSES, HEARING PROTECTION, AND GLOVES DO NOT WEAR LOOSE FITTING CLOTHES THAT COULD GET STUCK IN THE MACHINE MOVING PARTS, ONLY CHIP WOOD, CHILDREN SHOULD NOT RUN THIS EQUIPMENT, STAY ALERT OF YOUR SURROUNDING AND PERSONS THAT COULD APEAR IN THE CHIP PATH WHILE YOU ARE WORKING. UNIT IS DIRECT DRIVE.
PLEASE DO NOT RETURN TO THE STORE YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE CALL US AT 702-331-5353 FOR FAST WARRANTY PARTS AND QUESTIONS WHAT IS COVERED DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing defects in workmanship and materials under normal use and service for a period of one (1) year from the date of the original purchase.
