Owner’s Manual Model 2351 System Expansion Boards DoorKing, Inc. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586 www.doorking.com P/N 2351-065 REV F, 10/03 Copyright 2001 DoorKing, Inc. All rights reserved.
Use this manual with the following models only. Tracker expansion boards 2351-010 Rev E or higher. DoorKing, Inc. reserves the right to make changes in the products described in this manual without notice and without obligation of DoorKing, Inc. to notify any persons of any such revisions or changes. Additionally, DoorKing, Inc. makes no representations or warranties with respect to this manual. This manual is copyrighted, all rights reserved.
TABLE OF CONTENTS Section 1 – Setup 1.1 1.2 General Information..................................................................................................................................7 Tracker Board Input / Output Descriptions 1.2.1 Access Control Device (Weigand) Input ..................................................................................8 1.2.2 Gate Operator Data Input.........................................................................................................8 1.2.
Section 1 – Setup The model 2351 Tracker Expansion Board allows you to expand the number of entry points that the models 1803PC, 1815, 1817, 1818, 1833, 1835, 1837 and 1838 PC Programmable Entry Systems can control up to a maximum of 16. One Tracker board is required for each entry point. Tracker boards will interface with a variety of weigand devices including card readers, RF transmitters, digital keypads, etc.
1.2 Tracker Board Input/Output Descriptions 1.2.1 Access Control Device (Weigand) Input Tracker boards can accept weigand input data from most devices that output their data in a 26-bit weigand format. An access control device (a card reader for example) is connected to the tracker board at P2, terminals 6-7-8-9. When the tracker board receives the weigand data from the access device, it sends the data to the access system controller where the decision to grant or deny access is made.
1.2.6 Command Relay Input The command relay input (P2, terminals 8 & 17) is connected to the relay in the access system controller that activates when a valid device code is received by the controller. For example, when a card reader connected to the weigand input on the tracker board reads the card code, it inputs this information to the tracker board, which in turn sends the information to the access system controller. The access controller then makes the decision to grant or deny access.
1 2 3 Jumpers set individual board ID code P1 1 2 3 4 5 6 7 8 P2 MONITOR RELAY Programming switches set the Tracker board to operate in various modes. ALARM RELAY OUTPUT RELAY 2351-010 Board Settings 1 2 NO NC NO NC 3 NO NC 4 4 5 5 6 6 7 7 8 8 9 9 10 10 11 11 12 12 13 13 14 14 Relay shorting bars set each relay for N.O. or N.C. operation. 15 16 17 18 POWER DOORKING 2351-010 DOORKING, INC., INGLEWOOD, CA 90301 Title: 2351-010 Board Settings Date: 4/02 10 Dwg. No.
1.3 Monitor and Alarm Relay Operation The Tracker board provides relay contacts for monitoring and alarm purposes. There are two different modes in which the tracker board can be programmed to operate; MODE-1 and MODE-2. These different modes of operation are set by switch 1 and determine the operation of the MONITOR (R1) and ALARM (R2) relays on the tracker board. The mode of operation does not affect the OUTPUT (R3) relay.
1.3.2 Mode-2 In MODE-2 (switch 1 ON), the monitor relay is typically connected to a local alarm (bell, buzzer, light, etc.) and the alarm relay is typically connected to the buildings alarm system. In this mode, there are two distinct conditions under which the tracker board will respond to a door ajar condition; FORCED CONDITION and PROPER CONDITION.
SWITCHES 3 4 MONITOR RELAY Forced Condition ALARM RELAY Proper Condition Forced Condition Proper Condition A OFF Activates whenever door ajar Turns on after door ajar timer OFF Activates whenever door ajar Turns on-off in 1-second switch closes (door open). expires. switch closes (door open). intervals for length of time determined by switches 5&6. B OFF ON Activates whenever door ajar Proper condition disabled. switch closes (door open). C ON OFF Forced condition disabled.
1.4 Hold Open Features There are two hold open features associated with the Tracker expansion boards: hold open time zones and an override hold open command. An "Override Hold Open" command will cause ALL the tracker boards connected to the access control system to open a gate or unlock a door, and remain in this status until commanded to return to normal operation. 1.4.1 Hold Open Time Zones Hold open time zones are programmed in the Remote Account Manager for Windows (V 5.
1.5 Board and Relay Identification When using two or more Tracker boards connected to a single access system, the board jumpers on each tracker board must be set so that the access system can identify each tracker board. There are six sets of jumper pins on the tracker board labeled J1 through J6. Shorting bars placed on the jumper pins create a unique address for each tracker board to identify itself to the access control system. 1.5.
1.5.2 Relay Identification The models 1803PC, 1815, 1817, 1833, 1835 and 1837 telephone entry systems each have three relays (Relay 0, 1, and 2) on the control board while the 1818 and 1838 access control systems each have two (Relay 1, 2) relays. When Tracker boards are added to these systems, the output relay on the Tracker boards are listed in the software sequentially, beginning with Relay 3 (Relays 0, 1 and 2 are on the main control board).
Board 16 System Relay 18 Board 15 System Relay 17 Board 14 System Relay 16 Board 13 System Relay 15 Board 12 System Relay 14 Board 11 System Relay 13 Board 10 System Relay 12 Board 9 System Relay 11 Board and Relay Identification for 40 or 50 Series Controller Command Relay 1 (terminals 15-17) controls boards 9-16. Tracker boards 9-16 connect to weigand terminals 7-8-9 in the access controller.
Board 16 System Relay 18 Board 15 System Relay 17 Board 14 System Relay 16 Board 13 System Relay 15 Board 12 System Relay 14 Board 11 System Relay 13 Board 10 System Relay 12 Board 9 System Relay 11 Board and Relay Identification for 30 Series Controller Command Relay 1 (terminals 15-17) controls boards 9-16. 14 13 1833, 1835, 1837, 1838 Controller Tracker boards 9-16 connect to weigand terminals 11-12-13 in the access controller.
1.5.3 Terminal Identification TERMINAL P1 1 Monitor Relay 2 Monitor Relay 3 Alarm Relay 4 Alarm Relay 5 Output Relay 6 Output Relay 7 Weigand Output – Common 8 Weigand Output – Data 1 9 Weiagnd Output – Data 0 10 Battery Negative (-12VDC) 11 Battery Positive (+12VDC) 12 Earth Ground 13 16 VAC Input Power 14 16 VAC Input Power Data output to 1803PC, 1815, 1817, 1818, 1833, 1835, 1837 or 1838 access control system.
Terminal Identification P1 1 2 3 4 5 6 7 8 P2 1 Monitor Relay 2 Monitor Relay 3 Alarm Relay 4 4 Alarm Relay Gate 1, 2 - DATA COMMON 5 5 Output Relay Weigand In - DATA 0 6 6 Output Relay Weigand In - DATA 1 7 7 Weigand Out - Common Weigand In - COMMON 8 8 Weigand Out - Data 1 12 VDC Power 9 9 Weigand Out - Data 0 Board Communication 10 10 Battery Negative (-12 VDC) Gate 1 - Power Monitor 11 11 Battery Positive (+12 VDC) Gate 1 - Power Monitor 12 12 Earth Ground Ga
Section 2 - Installation The location of the tracker board(s) is dependent on the application that it is being used. Tracker boards can be installed in selected card reader and digital keypad housings, or they can be installed in their own enclosure (enclosures are optional and not included with the Tracker board). DoorKing has two enclosures available for this purpose. The small housing will hold a single tracker board and the large housing can hold up to four tracker boards.
2.1 Single Housing • P/N 2351-080 provides a lockable, weather resistant housing for a single tracker board. Single Board Enclosure 4.875 3.625 8.75 7.125 .187 DIA 4 PL 5.75 1.25 .875 DIA 2 PL 1 3.75 DOORKING, INC., INGLEWOOD, CA 90301 Title: Date: 22 Single Enclosure for 2351-010 Board P/N 2351-080 4/02 Dwg. No. M2351-065-5 Rev.
2.2 Quad Housing • P/N 2351-081 provides a lockable weather resistant housing for up to four (4) tracker boards. Includes terminal strips and four (4) convenience outlets for power transformers. FOUR BOARD ENCLOSURE .5 FRONT SIDE 4.0 .5 24 23.0 13.0 .875 DIA 2 PL 3.5 3.0 1.125 DIA 4.0 7.0 .875 DIA 2 PL 3.75 2.0 6.25 8.875 4.0 .875 DIA 6 PL 1.0 1.125 DIA 2.75 .875 BOTTOM 2.0 4.25 6.5 8.75 DOORKING, INC., INGLEWOOD, CA 90301 12.5 Title: 14.
Section 3 – Wiring Information Plan your wire runs before starting the installation. Use proper wire for the weigand lines, power wires, and be sure that the system is properly grounded. Check all local building ordinances and building codes prior to installing this system. Be sure your installation is in compliance with local codes.
3.1 Tracker Boards 1-8 Detail Wiring for 40 and 50 Series Boards • Maximum wire run between Tracker boards 1-8 is 500 feet total. • Do not use twisted pair wire with weigand output format. • Proper grounding is required! Ground wire should be a minimum 12 AWG.
3.2 Tracker Boards 9-16 Detail Wiring for 40 Series Boards • Maximum wire run between Tracker boards 9-16 is 500 feet total. • Do not use twisted pair wire with weigand output format. • Proper grounding is required! Ground wire should be a minimum 12 AWG.
3.3 Tracker Boards 1-8 Detail Wiring for 30 Series Boards • Maximum wire run between Tracker boards 1-8 is 500 feet total. • Do not use twisted pair wire with weigand output format. • Proper grounding is required! Ground wire should be a minimum 12 AWG. 30 Series Controller to 2351-010 Expansion Boards 1-8 Detail Wiring 1 2 3 4 5 6 RS 232 Connection Elevator Control 1 2 3 14 13 12 11 Auxiliary Terminals NOTES: Controller main terminals 15-16-17 = SYSTEM RELAY 1.
3.4 Tracker Boards 9-16 Detail Wiring for 30 Series Boards • Maximum wire run between Tracker boards 9-16 is 500 feet total. • Do not use twisted pair wire with weigand output format. • Proper grounding is required! Ground wire should be a minimum 12 AWG 30 Series Controller to 2351-010 Expansion Boards 1-16 Detail Wiring 1 2 3 4 5 6 RS 232 Connection Elevator Control 10 1 2 3 7 P2 + 12 VDC COMMON DATA 1 DATA 0 NOTES: Controller main terminals 15-16-17 = SYSTEM RELAY 1.
3.5 Block Diagram Single Door – Typical • The block diagram below shows the necessary wire runs needed when all options (gate operator data, alarm outputs, door and reset switches, request to exit, etc.) available with the 2351 Tracker board are utilized. BLOCK DIAGRAM - 2351 BOARD TO CONTROLLER AND OTHER BOARDS 6 GATE OPER 1 5 2 LOCAL ALARM GATE OPER 2 5 2 ALARM SYSTEM CARD READER 4 2 GATE OR DOOR 2351-010 2 LOCK POWER 1 2 Light Power 2 4 1 common conductor to all three switches.
3.6 Door Control Wiring Detail - Typical • Set output relay shorting bar on the Tracker board to N.O. (Normally Open) when using failsecure (electric strikes) locking devices; set to N.C. (Normally Closed) when using fail-safe (magnetic locks) locking devices.
3.7 Gate Operator Data • Each tracker board can report data to the access control system from two (2) DKS gate operators; a slide or swing gate operator and a barrier gate operator. See page 32 for a list of the events that can be reported.
Wiring for 9310 Gate Operator Only 2351-010 Tracker Board 3 24V COMMON 1 OPEN / RADIO RELAY 2 2 P2 1 Gate 1 Data IN 24V RADIO PWR 3 2 Gate 1 BUSY 3 Gate 2 Data IN OPEN 4 1 4 4 Gate 2 BUSY 5 Gate 1, 2 Data COMMON PARTIAL OPEN 5 6 7 REVERSE / STOP 6 8 9 3-BUTTON OPEN 7 10 11 3-BUTTON CLOSE 8 12 Gate 1 Power Monitor 13 Gate 2 Power Monitor TRACKER DATA 9 4 14 15 TRACKER BUSY 10 16 17 18 1 Belden 9931 or Equivalent. 2 Connect to Tracker board terminal P1-5.
3.8 General Wiring Information The wiring of the tracker board(s) is an extremely important and integral part of the overall access control system. Use proper wire for weigand and power wire runs, and be sure that the system is properly grounded. Check all local building ordinances and building codes prior to installing the system. Be sure that your installation is in compliance with these codes. • Use only the supplied power transformers (16 VAC, 20 VA) or U.L.
Section 4 – Trouble Shooting Before beginning any trouble shooting, check all wiring and look for any loose connections. Double check your wiring! The tracker expansion board in some applications may have over 20 wires connected directly to the board terminal strips. Be sure that you have a good VOM (Volt-Ohm-Meter) to assist you when checking voltages and continuity. Check the programming switches to be sure that the tracker board is setup to operate as desired.
4.2 Weigand Device Data The weigand device (card reader, RF receiver, digital, etc.) must output data in the 26-bit weigand format. The tracker board is not capable of receiving any other weigand format from these devices. The weigand device must be connected to terminal P2, pins 6-7-8-9 as described in section 4.4 of this manual. Two weigand devices may be connected in parallel to the weigand input on the tracker board.
4.3 Gate Operator Data Be sure that the gate operator has Gate Tracker capability. This can be determined by checking the revision letter of the control board in the operator. Gate operator control boards with Gate Tracker capability are listed below. • 4402 Rev A or higher. • 4403 Rev A or higher. • 4501 Rev R or higher; 4502 Rev A or higher. • 4601 Rev J or higher; 4602 Rev A or higher. • 1601 Rev Q or higher.
Gate Operator Event (transaction) Reports The tracker interface board sends the following gate operator data to the DKS access control system. This data is stored in a separate file in the access system and can be viewed by clicking the GATE button on the transaction report screen in the DoorKing Remote Account Manager for Windows software. Each event is date and time stamped. Event (transaction) Description Gate Operate 100 Times Transaction sent each time gate operator goes through 100 operations.
