User Guide

Car stereo / amplifier
DLS UP1C, ULTIMATE PRO SERIES TWEETER
Black -
Blue +
Red
Black -
Red +
Tweeter
Bass/mid
Tweeter filter 9-25604
Black -
Red +
Low-pass filter
Yellow
Speaker connection and tweeter level
select:
When used as a tune-up tweeter to existing speakers the
filters coming with this tweeter should be connected in
series with respective speaker element as on the drawing.
Select tweeter level by connecting the red cable to either
the red or yellow cable coming out from the filter box. If the
tweeter is directed towards the listener, low level is to be
prefered. Otherwise make your own tests for best result.
Sometimes the midrange can be improved by phase reversing
the tweeter. Try it and make your own judgement.
NOTE! Some kind of highpass filters (active or
passive) must be used. If the tweeters are connected
without filters they may be damaged and the sound
reproduction becomes bad.
THE KIT CONTAINS:
Y 2 pcs 28 mm (1,1") tweeter elements
 Y 2 pcs 12 dB high-pass cable filter with level
select (not included when UP1C is a part of a
complete system)
 Y Mounting accessories for dash-
and recessed mounting
FILTER CONNECTION
UP1C connected to a system with an existing bass/
mid speaker with it´s own low-pass filter. This is not
the perfect filter solution. The best sound is achieved
if all filters are perfectly designed to match the
different drivers in the system.
Speaker
impedance 4Ω
Tweeter level select:
Red to red = high
Red to yellow = low
Thank you for buying DLS UP1C tweeters. UP1C tweeters are
included in the DLS ULTIMATE PRO speaker kits UP5, UP6, UP35
and UP36.
They can also be bought separately for use as "tune-up tweeters"
to improve the treble in any system.
DLS Svenska AB
P.O. Box 13029
S-402 51 Göteborg, Sweden
Tel. [phone]
Fax [phone]
E-mail: [e-mail]
www.dls.se
If you have any questions about this product, contact
your local dealer or DLS customer support center.
Art.no 10-25301C
Size 28 mm / 1,1"
Nom. power (RMS) 50 Watts (80 Watts max)
Freq. range 1,5 kHz-20 kHz
Sensitivity 93 dB
X-over frequency 4 kHz with filter 9-25604
Overall dimensions 44,5 mm / 1,75"
Magnet diameter 28 mm / 1,1"
Mounting depth 18 mm / 0,71"
Mounting hole 48 mm / 1,89"
Cone material Hand treated fabric
FACTS ABOUT DLS UP1C TWEETER
FLUSH MOUNTING:
You need a hole with a diameter of 48 mm / 1,89" in the door side.
The cup is attached to the door side using the metal bracket
screwed together with the cup and the bracket pressing towards
the door side back.
Put the tweeter element into the cup with the cable going out
through the bottom hole. Then attach the element into the cup and
turn it clockwise to attach to the cup. When removing the element
from the cup, turn it ccw and lift it out
SURFACE MOUNTING:
MOUNTING:
UP1 can be mounted on the dashboard with the angled cup or
recessed in a doorside with the flush cup.
For angled surface
mount together with the
angled cup:
The tweeter element is
attached to the cup by
fitting the three wings
on the angled cup into
the tracks of the ele-
ment and then turn it
clockwise. When remo-
ving the element from
the cup, turn it ccw and
lift it up.
When used in combination with DLS UP5, UP6, UP35 or
UP36 the filter boxes in the kits should be used.
DLS Svenska AB 02-03-04