User Manual

ManualsBrandsDLUX ManualsHobbyTurnigy dlux 250A HV 14s 60v ESC

Hextronik AIRplane [6-12]ESC Manual [ Model 2 ] Page 1 7/21/2014

Dear customer,

Thanks for purchase of our Brushless Motor Controller.

Please read and pay carefully attention to the following instructions before you start to work with your motor and

controller.

Wires Connection:

The speed controller can be connected to the motor by soldering directly or with high quality connectors.

Always use new connectors, which should be soldered carefully to the cables and insulated with heat shrink tube. The maximum

length of the battery pack wires shall be within 6 inches.

 Solder controller to the motor wires.

 Solder appropriate connectors to the battery wires.

 Insulate all solder connectors with heat shrink tubes.

 Plug the “JR” connector into the receiver throttle channel.

 Controller Red and Black wires connects to battery pack Red and Black wires respectively.

Installing the Controller:

Install the controller in the model so that it is free from vibration and shock, using Velcro or double sided foam tape. Make sure

there is sufficient cooling for the motor and controller by ducting air through cooling holes from outside airflow.

Failure to do so, will be cause motor or controller damaged.

Normal start up:

Switch on transmitter and check throttle settings are +/-100% (for computer radio).

For Futaba Radio programs use the “Servo Reverse” function on the throttle channel.

Pulls throttle stick in down or brake position;

 Transmitter switches “On”,

 Connects battery pack to the controller

 Receiver switches “On” (BEC switch on).

 You will hear one beep for Brake on or two tones for Brake off.

 The position of full throttle will be calibrated automatically.

 You motor now is ready to run.

WARNING:

 Always connect the motor battery pack just before flight and disconnects it immediately after landing.

 Once the motor battery pack is connected, handle the model with extremely care!

 Ensure that you are well clear of the propeller at all times.

 Rotating propeller is extremely dangerous!

 Even when the receiver (BEC) switch is “OFF”, but please remember the motor battery pack may still be

connected. Handle the model with extremely cares and stay clear of the propeller!

Factory default settings

Brake : Off

Battery Type : Lipo 10S

Cut-Off Voltage : 3.2V

Rotation Reverse : Normal

Acceleration : High

Timing : Automatic

Under Voltage : Reduce Power

Summary of content (6 pages)

PAGE 1
Dear customer, Thanks for purchase of our Brushless Motor Controller. Please read and pay carefully attention to the following instructions before you start to work with your motor and controller. Wires Connection: The speed controller can be connected to the motor by soldering directly or with high quality connectors. Always use new connectors, which should be soldered carefully to the cables and insulated with heat shrink tube. The maximum length of the battery pack wires shall be within 6 inches.
PAGE 2
Switch Frequency RPM Control : : 8KHz Off How to program your controller       Switch on the transmitter and push to the throttle stick to full throttle. Connects the motor battery pack and turns on the receiver (BEC) switch. Waits for 5 sec, you’ll hear tones; setup mode is entered: __ -When you hear the desired tones, pull the throttle down, then you’ll hear two confirmation tones. The setting is now memorized.
PAGE 3
x3 Lipo 14S x3 3. Rotation Reverse This function is to change the motor rotation direction. (for example: Right to Left, or vice versa) Reverse motor rotation 4. Acceleration When gearbox drive system is used. It’s highly recommended to enable the Soft start. Because it’s protecting the gearbox not to damage especially large diameter of propeller is used. Disable the soft start function when direct drive system is used or being in speed competition Low: High: 5.
PAGE 4
Medium High 7. Switching Frequency The controller has two switching frequency modes. 8KHz is good for ALL types of two pole motor, 16KHz is good for multi pole motors. 8 KHz: 16 KHz 8. Restore Factory Default Setting 9.
PAGE 5
10. Program Box Set Flow Chart Hextronik Program BOX V1.0 AIRplane-OPT Ver: B260101 Battery Type Nicd/Nimh、Lipo 6s、Lipo7s、Lipo 8s、Lipo 9s、Lipo 10s、Lipo 11s、Lipo 12s ,lipo13s,lipo14S Cut-Off Voltage 2.5V、2.6V、2.7V、2.8V、2.9V、3.0V、3.1V、3.2V、3.3V、3.4V、 3.
PAGE 6
Notice for Operation:  Temperature overload protection is built into the speed controller, it turns off the motor immediately when the temperature reaches 212°F/100°C.  Do Not connect the controller to just ‘any’ kind of power sources. Take care to ensure that the right polarity of NiCd, NiMH or Li-Poly power packs.  Do Not connect the motor battery to the wrong polarity, the controller will be seriously damaged.