USER MANUAL What is the MAXI Switch? • 120cm*75cm - 4*2.
MAXI SWITCH USER MANUAL STEP 2-a : STEP 1 : • Approach the MAXI Switch head light in folded position between the MAXI YOKE’s arms. • Install the spigot on the MAXI YOKE with given wing knob. • Install the MAXI YOKE on a stand (two spigot sizes available 16mm & 28mm). • Make sure the handles are loose before installing the MAXI.
STEP 2-b : STEP 3 : • Guide the MAXI Switch’s grooves onto the disks of the MAXI Yoke. • The MAXI Switch head light is now installed on the MAXI YOKE.
STEP 4 : SAFETY WARNING : do not tilt the MAXI above 90° on the yoke when in closed position. It will disengage the Maxi from its yoke. • Lift up one of the two panels until both are parallel.
STEP 5 : TIP : • Slide the safety catch into position on either side of the MAXI Switch. • Plug the MAXI Switch head light to the MAXI CONTROLLER. • If needed, you can install the MAXI CONTROLLER at the back of the fixture. To do so, twist and lock it as easy as the marks suggest it. Make sure the locking pin is in position.
TRANSPORTING THE MAXI WITH THE YOKE : • Insert MAXI YOKE’s ball pins on both sides to secure the MAXI Switch head light in folded position if needed (bag, transport, ect.). Ensure the handles are securely fastened.
SPLITTING PROCEDURE : • Present the MAXI head light folded on a soft and flat surface. • Unscrew the nut with a 5mm allen key on both sides. You will be able to remove it completely once the two panels are separated.
SPLITTING PROCEDURE (Continued) : • Once the nuts are loose, separate the panels. You can screw back each nut on it’s axis in order not to loose them.
MAXI-CT-SW 10 8 1 2 9 3 4 5 1. Menu • Go to the general menu 2. Back • Step back in menu • Lock/unlock MAXI Switch when pressed for 2 secs 3. Switch • Change between CCT and intensity control • Hold the Switch button for 2 secs to activate split mode and control each panel separately 11 12 7 13 14 6 4. CCT • Quickly change from 3200°k to 5600°K • Enter the preset menu to store or recall values when pressed for 2 secs 5.
MAXI SWITCH USER MANUAL 1. Connect the Maxi Switch Controls (MAXI-CT-SW) to the MAXI power supply unit (MAXI-PSU-SW) and connect the power supply to a 110VAC or 220VAC plug. You can also input any 24VDC (min 20A) into the Maxi Switch Controls. 2. Connect the head light to its controller. 3. Turn on the MAXI Switch by selecting which power mode you want to use (MAXI or SPLIT) with the selector.
CUSTOM MODE (Continued) : These informations can be find in the “info” section of the MAXI Switch Controls menu. Wireless DMX dot is red when no signal is received, green when the MAXI Switch is connected to a Wireless DMX emitter. • To synchronize with a new emitter, go back to general menu and enter Wireless DMX mode again Wi-Fi dot is red when no signal is received, green when the MAXI Switch is connected to a Wi-Fi device with an Art-Net app enabled.
UBB/MAXI CT USAGE EXAMPLE Light 1 Light console Light 2 DMG Lumière lights or any DMX enabled light Light 1 Light 2 DMG Lumière lights or any DMX enabled light DMG Lumière lights or any Wireless DMX enabled light Our wireless DMX is compatible with any powered devices.
MAXI SWITCH STANDARD CABLES DIAGRAM MAXI DRIVER OUTPUT MAXI HL INPUT 10 meters 2x13 AWG NEUTRIK SpeakCON 2x NL4MP NL4FC NEUTRIK SpeakCON 2x NL4FC NLT4MX-BAG QTY : 2 MAXI PSU INPUT 110/220V NEUTRIK PowerCON True1 Duplex NAC3PX 1,5 meter PowerCon True 1 Power chord (EU/US/UK/...
MAXI SWITCH OPTIONAL CABLES DIAGRAM MAXI PSU 110/220V INPUT NEUTRIK PowerCON True1 Duplex NAC3PX MAXI PSU 110/220V OUTPUT 0,5/1/1,5 meter NEUTRIK PowerCon True 1 Extension Cord NEUTRIK PowerCON True1 Duplex NAC3PX 10 meters 2x13 AWG MAXI DRIVER INPUT MAXI PSU OUTPUT CHOGORI 24003636-02 CHOGORI 24003131-04 CHOGORI 24003536-02 CHOGORI 24003231-04 DMG | User Manual - MAXI Switch 14