Installation guide

ManualsBrandsDMP Electronics ManualsComputer equipmentSecurity Command 690

INSTALLATION GUIDE

690/690F, 790/790F and 693/793 Security Command

™

Keypads

Description

The DMP 690/690F, 790/790F and 693/793 Security Command™ LCD Keypads are the industry’s rst burglary/re

keypads with integrated access control capability. Each keypad provides four 2-button Panic keys, an AC power

LED, an Armed LED, 32-character display, backlit keyboard with easy-to-read lettering and an internal speaker. In

addition, the Models 790/790F and 793 keypads also provide four fully programmable Class B, Style A protection

zones you can program for a variety of burglary, re, and access control applications.

The 693 and 793 keypads provide a built-in proximity card reader designed to read HID 1300 Series proximity

credentials. The Model 793 keypad also provides a door strike relay and allows Wiegand input from HID, DMP, or

other external card readers. When presenting a DMP credential use the keypad built-in card reader. HID credentials

can be read at either the keypad or the external card reader.

Note: The 690F and 790F Security Command LCD keypads do not provide an Armed LED. These keypads may be

installed in re only applications.

Installing the Keypad

The keypads each use the same plastic housing. They are all designed to easily install on any 4” square box, 3-gang

switch box, 695 and 696 backbox, or at surface. Figure 1 shows the keypad housing base mounting hole locations.

Removing the Base

The keypad housing is made up of two parts: the front, which contains the circuit board

and other components, and the base. To mount the keypad, remove the base from the

front by inserting a at screwdriver into one of the openings on the bottom. Twist the

screwdriver while pulling the halves apart. Repeat with the other opening.

Harness Wiring

Figure 1 shows wiring harness assignments. Observe wire colors when connecting the red, yellow, green, and black

wires to the keypad bus. When wiring directly to the panel terminals, connect red to panel terminal 7, yellow to

terminal 8, green to 9, and black to panel terminal 10. Use 1k Ohm EOL resistors, DMP Model 311, on keypad zones

1 through 4.

The 690, 690F, and 693 keypads are supplied with a 4-wire harness for panel keypad bus connection.

The 790, 790F, and 793 keypads are supplied with a 12-wire data bus/zone harness. Four wires connect to the

keypad bus, the same way the 690 and 690F keypad harness connects. The remaining eight wires are for the four

zone inputs: two wires for each zone.

The 793 keypad is also supplied with one 5-wire output/reader harness.

Surface and Backbox

Mounting Holes

Combined 4-square

and 3-gang switch box

Mounting Holes

Keypad Back

Surface and Backbox

Mounting Holes

1K EOL

Green/White – Connect Reader Data 0

Whit

e – Connect Reader Data 1

Orange – Door Strike Normally Open

Gray – Door Strike Common

Violet

– Door Strike Normally Closed

Yellow/Whit

White/Yello

Orange White

White/Orange

Red/White

White/Red

Brown/White

White/Brow

Black – Ground

Green – Receive Data

Yellow – Send Data

Red – Keypad Power

– Zone 4

– Zone 3

– Zone

– Zone 1

Output Reader

793 Keypad

Zones 1 through 4

790/790F, and 793

Keypads

All Keypads

Figure 1: Keypad Back Showing Wiring Harness Assignments

Summary of content (12 pages)

PAGE 1
INSTALLATION GUIDE 690/690F, 790/790F and 693/793 Security Command™ Keypads Description The DMP 690/690F, 790/790F and 693/793 Security Command™ LCD Keypads are the industry’s first burglary/fire keypads with integrated access control capability. Each keypad provides four 2-button Panic keys, an AC power LED, an Armed LED, 32-character display, backlit keyboard with easy-to-read lettering and an internal speaker.
PAGE 2
Additional Power Supply If the current draw for all keypads exceeds the panel output, you can provide additional current by adding a Model 505-12 auxiliary power supply. Connect all keypad common wires to the power supply negative terminal. Run a jumper wire from the power supply negative terminal to the panel common terminal. Connect all keypad power (+12 VDC) wires to the power supply positive terminal. Do NOT connect the power supply positive terminal to any panel terminal.
PAGE 3
793 Door Strike Relay Operation As soon as the user code sent from the reader is verified by the panel, the keypad Door Strike relay activates for five seconds. During this time, the access door connected to Zone 2 must be opened to start the programmed entry/exit timer and zone soft shunt. Note: The 5-second delay length is programmable in the panel when the keypad is used on an XR500 Series, XR2500F, or XR200-485 panels.
PAGE 4
End-User Options The LCD Keypads provide three keypad adjustments the end-user can make through a User Options Menu. The user can also view the keypad model number and address in User Options. On all keypads press and hold the Back Arrow (<—) and CMD (COMMAND) keys for two seconds to access User Options. The keypad display changes to SET BRIGHTNESS. Use the CMD key to display the next option or press the <— key to exit the User Options function.
PAGE 5
Installer Options Menu The LCD keypads provide Keypad Option and Keypad Diagnostic menus to allow installers and service technicians to configure and test keypad operation. Accessing Installer Options You can only access the Installer Options Menu through the User Options function. Hold down the <— and CMD keys for two seconds to display SET BRIGHTNESS. Enter the code 3577 (INST) and press CMD. The display changes to KPD OPT (keypad options) KPD DIAG (keypad diagnostics) and STOP.
PAGE 6
ZONE 2 SOFTSHUNT TIME: 40 Zone 2 Soft-Shunt Time (793 only) Enter the number of Soft-Shunt seconds to elapse before the Soft-Shunt timer expires. Range is from 20 to 250 seconds. Press any top row select key to enter the number of seconds. Once the door strike relay is activated, the user has 5 seconds to open the door connected to zone 2. The zone is then shunted for the programmed time or until the contact restores to normal.
PAGE 7
WIEGAND CODE LENGTH: 45 Custom Card Definitions (693 and 793 only) When using a custom credential, enter the total number of bits to be received in Wiegand code including parity bits. Press any top row Select key to enter a number between 0-255 to equal the number of bits. Default is 45 bits. Typically, an access card contains data bits for a site code, a user code, and start/stop/ parity bits. The starting position location and code length must be determined and programmed into the keypad.
PAGE 8
NO. OF USER CODE DIGITS: 5 Number of User Code Digits (693 and 793 only) The keypad recognizes user codes from four to six digits in length. Press any Select key to enter the user code digit length being used by the panel. Default is 5. When searching the bit string from the reader for the user code, the digits are identified and read from left to right. When a four-digit user code is selected only the first four digits of the string are read.
PAGE 9
Accessing Keypad Diagnostics If necessary, refer to Access the User Menu on the previous page. KPD KPD OPT DIAG STOP Keypad Diagnostics (KPD DIAG) The Keypad Diagnostic option allows you to check the display segments, check the keyboard backlighting, and test individual keys. Press the Select key under KPD DIAG. The keypad lights all display segments and illuminates the keyboard in green. A few seconds later the keypad turns the display off and illuminates the keyboard in red.
PAGE 10
693/793 User’s Guide There are three different sections: Keypad Arming and Disarming, Keypad Door Strike, and Keypad Entry Delay. All of the examples below assume that CLOSING CODE is YES in panel programming. Keypad Arming and Disarming Area System Arming and Disarming Press CMD, the keypad displays ARM DISARM. Press the Select key under either option. The keypad displays ENTER CODE: -. Present your card to the keypad reader.
PAGE 11
Keypad Door Strike Area and All/Perimeter Door Strike From the Status List, present your card to the reader. Once validated by the system, all areas assigned to your code arm or disarm automatically and the 793 keypad Door Strike relay activates. Home/Away systems only activate the 793 Door Strike relay when arming and disarming. ABC SECURITY MON 10:20 AM While the keypad is in the Status List, present your access card. The relay activates for 5 seconds during which time you can open the door.
PAGE 12
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made by the user and not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.