Instruction Manual

◇ 蓝牙版本：Bluetooth V5.0
◇ 蓝牙协议:a2dp\avctp\avdtp\avrcp\hfp\spp\smp
◇ 工作电压：DC 2.2V-5.5V
◇ 有效距离：10M(无任何较大障碍物的理想环境中)
◇ 支持模式：HFP/ HSP/ A2DP/ AVRCP
◇ 灵敏度：105dB±3dB S.P.L at 1KHz
◇ 充电输入：5V /500mA
◇ 充电时间：给充电盒充电约1小时,充电盒给耳机充
电约45分钟
◇ 充电仓给耳机充电次数：双耳约3次；单耳约6次
◇ 使用小时：通话约3小时，播放音乐约2.5小时
◇ 待机时间：约80小时
重要提示
◇ 请勿自行拆卸本产品。
◇ 请使用标准的充电线、5V充电器充电,以免损坏本机和
发生意外。
◇ 本机器支持左右耳佩戴。
包装清单：
◇ 蓝牙耳机主机
◇ 耳机充电盒
◇ Micro 5pin 充电线
◇ 备用大、小耳冒
◇ 使用说明书
配对方式
1.从充电仓取出或者同时长按左、右耳机多功能键3秒开机，
直至红蓝灯交替闪烁,进入对耳搜索配对状态,进入对耳自
动配对,配对成功后主耳（右耳）持续红蓝灯交替闪烁,副
耳为蓝灯慢闪,同时播放对耳配对成功提示音。
2.启动手机 或者 其它设备的蓝牙功能，如果是安卓系统手
机或者设备请点击手机"搜寻蓝牙设备"选项,如果是IOS系
统的手机或者设备则会自动搜索设备;当搜寻到该蓝牙耳
机的型号后,点击进入配对;当配对成功后,主（右）耳机
会发出连接成功的提示音,左右耳机指示灯变为蓝灯慢闪,
进入连接待机状态,配对成功后主耳为右声道,副耳为左
声道。
3.两只耳机也可单独与手机进行配对使用,操作方法可按上
步骤2操作手法进行操作。
充电操作
1.将Micro USB充电线一头插上充电盒的USB口一头插上充电
器即可给充电盒充电，当充电盒电量在对应指示灯的指示
范围时,该位置的白色指示灯间隔2秒闪一次,直至该指示
灯的电量范围充满后则长亮进入下一电量范围的指示灯闪
烁,全部充满电后所有指示灯长亮。
2.给耳机充电:将耳机放入充电仓即可自动充电,充电时耳机
指示灯为红色，充满电后熄灭；充电仓白色指示灯长亮
（充电仓满电时,4个电量指示灯全亮,当充电他电量下降达
到相应电量时,对应的指示灯则熄灭 ),当耳机充满电后充
电仓白色指示灯全部熄灭。
1.开机
将耳机从充电仓拿出自动开机或长按左右耳机多功能键
3秒开机。
2.关机
将耳机放充电仓关机/长按左右耳机多功能键5秒关机。
3.开机回连
当配对成功后，第二次开机时蓝牙耳机优先进入回连状
态自动回连已连接过的手机。
4.播放/暂停
在待机状态下，单击左右耳机多功能键均可直接播放音
乐,播放时单击左右耳机多功能键可暂停播放。
5.来电接听
手机来电时，单击左右耳机多功能键均可接听电话。
6.来电挂断
手机通话时，单击左右耳机多功能键均可挂断电话。
7.来电拒接
手机来电时，长按左右耳机多功能键2秒均可拒接来电。
8.末号重拨
在待机或者播放音乐时，三击左耳机多功能键即可拨打
您通话记录中最后一个拨打过的电话。
9.启动语音助手
三击右耳机功能键即可启动苹果Siri或谷歌语音助手进行
语音控制手机操作。
10.低电量提示
当蓝牙耳机电池电量不足时，间隔30秒播放一次电量不足
提示音直至耳机低电关机。
一.产品参数：
二.功能操作：
注意事项
1.请在安全的环境下充电。在给充电仓充电时当充电指示灯
指示满电后请忙将充电仓与USB充电线分开,以免在长时间
插着充电对充电仓造成损伤。
2.在音乐播放时,请将音乐调至合适音量大小,以免长期在大
音量状态下对听力造成损伤。
3.尽量避免在有干扰源的地方使用本耳机,否则有可能对耳
机信号产生影响。
4.尽量避免在有腐蚀的环境中使用本耳机，以免对耳机的功
能产生影响。
温馨提示：在您首次使用时，请你通过随机附带的数据线连
接电源适配器进行充电1~2小时，以达到内置电池最佳使用效
果。在使蓝牙耳机听音乐或者通话时，请注意适当调节音量
大小，以免过大的音量对您的听力造成影响！
无线充蓝牙耳机
一.产品示意图：
使用无线充蓝牙耳机之前；请阅读使用说明书
1.麦克风孔
2.LED指示灯孔
4.充电接触点
3.多功能按键
5.充电顶针
6.USB充电口
Wireless bluetooth headset
Product schematic diagram
1.Microphone port
2.LED indicalor
3.Multi-functon button
4.Charging contact
5.Charging thimble
6.USB Charging PORT
Please read the instruction manual before
operating the wireless charger Q96
◇ Product Specifications
◇ Bluetooth Version: Bluetooth V5.0
◇ Bluetooth Protocol: a2dp\avctp\avdtp\avrcp\hfp\spp\smp
◇ Working Voltage: DC 2.2V-5.5V
◇ Transmission Range: 10M (Ideal environment without any
giant obstacles)
◇ Modes Available: HFP/ HSP/ A2DP/ AVRCP
◇ Sensitivity: 105dB±3dB S.P.L at 1KHz
◇ Charging Input: 5V/500mA
◇ Charging Time: 1 hour for charging the case, 45 minutes for
charging the earbuds.
◇ Times for earbuds to be charged by the box: 3 times for dual
earbuds, 6 times for single earbud.
◇ Playing Time: 3 hours for calling, 2.5 hours for playing music
◇ Standby Time: Around 80 hours
Functional operation instructions
1.Boot
Take the headset out of the charging compartment and
automatically turn it on or press and hold the left and right
headset multifunction button for 3 seconds
2.Shut down
Put the headset into the charging compartment and turn it
off automatically.Press and hold the left and right headset
multifunction button for 5 seconds to shut down.
3.Boot back
When the pairing is successful, the bluetooth headset
preferentially enters the connected state when the second
time is turned on,and automatically connects back to the
connected mobile phone.
4.Play/pause
In the standby mode,click the left and right earphones
Product Specification
2.Start the bluetooth function of the mobile phone or other
devices. If it is an Android mobile phone or device,please click
the"Search for bluetooth device"option.If it is the IOS system
mobile phone or device,it will automatically search for the
device;when searching for the model of the bluetooth headset
after that,click to enter the pairing;when the pairing is
successfully, the main (right)earphone will make a prompt to
connect successfully,and the left and right earphones will turn
blue and flash slowly,and enter the connection standby state.
After the pairing is successfully,the main ear is the right
channel. The secondary ear is the left channel.
3.The two earphones can also be paired with the mobile phone
separately.The operation method can be operated according to
the above step 2 operation method .
Charging operation
1.plug the micro USB charging cable into the USB port of the
charging compartment and plug in the charger to charge the
charging compartment . When the charging power is within the
indication range of the corresponding indicator light,the white
indicator light of the position flashes once every 2 seconds
untill when the indicator’s power range is full, the indicator
light that is on for the next power range will flash. When all the
lights are fully charged,all the indicators will be on.
2.Charging the headset: put the headset into the charging
compartment to automatically charge.When charging,the
headset indicator is red.When the battery is fully charged,it
will be off;the charging compartment white indicator will be on.
When the charging compartment is fully charged,the four
battery indicator lights are all on.When the charging capacity
drops to the corresponding power,the corresponding indicator
light goes out.When earphone is fully charged,the white light
of the charging compartment is completely extinguished.
multi-function keys to play music directly.When playing, click
the left and right earphones multi-function keys to pause
playback.
5.Call answering
When the mobile phone calls,click the left and right
earphones multifunction button to answer the call.
6.Call hang up
When the phone is talking ,click the left and right earphones
multi-fuction button to hang up the phone.
7.Call rejection
When the mobile phone calls,long press the left and right
headphones multi-function button for 2 seconds to reject the
call.
8.Redial
While on standby or playing music, you can dial the last call
you made in your call history by tapping the left headset
multifuction button.
9.Start voice assistant
Three-click the right headset multi-function button to start
Apples siri or Google Voice Assistant for voice control mobile
phone operation.
10.Low battery prompt
When the battery of the bluetooth headset is low, the low
battery tone will be played every 30 seconds untill the headset
is powered off.
Pairing method
1.Take out from the charging bin or press and hold the left and
right earphones multi- function button for 3 seconds to turn on
until the red and blue lights flash alternately,enter the ear
search pairing state,enter the ear pair automatic matching, and
match the main ear (right ear)The red and blue lights are
alternately flashing,the secondary ear is flashing slowly,and the
paired ear is successfully played.
Precautions
1.Please charge in a safe environment.When charging the
charging compartment,please charge the charging
compartment separately from the USB charging cable as soon
as the charging indicator indicates full power,so as to avoid
damage to the charging compartment after a long time of
charging.
2.When playing music,please adjust the music to the
appropriate volume to avoid hearing damage at high volume
for a long time.
3.Try to avoid using the headset in a place with interference
sources, otherwise it may affect the headphone signal.
4.Try to avoid using the headset in a corrosive environment to
avoid affecting the function of the headset.
Tips: When you listen to music or have a call with bluetooth
headset, please pay attention to adjust the volume properly, so
as not to affect the hearing of excessive volume!
Product number A6S
◇ Bluetooth version Bluetooth V5 0
◇ Battery specification: Headset 3.7V/45mAh;Charging box
3.7V/280mAh
◇ Support mode:HFP/HSP/A2DP/ AVRCP
◇ Sensitivity:105dB±3dB S.P L at 1 KHZ
◇ Transmission distance: 10 meters(in an ideal environment
without any major obstacles)
◇ Play time:About 2.5 hours
◇ Call time: About 3 hours
◇ Standby time:About 80 hours
◇ Charging time:Charge the charging compartment for about
1 hours,and charge the headset for about 1 hour
◇ Charging box to charge the headset:About3 times
Functional operation instructions
1.Boot
Take the headset out of the charging compartment and
automatically turn it on or press and hold the left and right
headset multifunction button for 3 seconds
2.Shut down
Put the headset into the charging compartment and turn it
off automatically.Press and hold the left and right headset
multifunction button for 5 seconds to shut down.
3.Boot back
When the pairing is successful,the bluetooth headset
preferentially enters the connected state when the second
time is turned on,and automatically connects back to the
connected mobile phone.
4.Play/pause
In the standby mode,click the left and right earphones
Product Specification
◇ :
: .
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: 1) this device may not cause harmful interference, and 2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try correct the interference by one or more of the following
measures:
-
Reorient the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could
void your authority to operate the equipment.