Manual

5
3.7 Precautions
■
Please make the Dobot Magician in the workspace with a 45° angle between the Fore-
arm and Rear Arm (as shown in Figure 1.1) before starting up. If the LED indicator turns
red after starting up, it indicates that the Dobot Magician is at a limited position. Please
make the Dobot Magician in the workspace.
Figure 1.1 The Forearm and Rear Arm position
■
Dobot Magician will move slowly to the specific position when shutdown. DO NOT put
hands into the workspace of the Dobot while running, to avoid bruising or pinching. Only
once the LED indicator completely turns off, the Dobot Magician can be powered down.
■
If the coordinates of the Dobot Magician shown on the DobotStudio are abnormal, please
press the Reset button on the back of the base to reset Dobot Magician or click Home on
the DobotStudio page to perform homing.
■
During resetting, Dobot Magician will disconnect from the PC automatically and the LED
indicator on the base turns yellow. About 5 seconds later, if the LED indicator turns
green, it indicates that the reset is successful.
■
During homing, Dobot Magician will rotate clockwise to the limited position and then re-
turn to the homing point automatically, and the LED indicator on the base turns blue and
is blinking. After homing, if there is a beep sound and the LED indicator turns green, it in-
dicates that the homing is successful.
■
Please turn off the Dobot Magician completely first before connecting or disconnecting
external equipment, such as Bluetooth, WIFI, stick controller, infrared sensor, color
sensor, etc. Or, it causes damage to your device.
■
Please wear the lasing protective eyeglass when using the laser module. Please protect
your eyes and skin from the laser.
■
The heating rod will produce high temperature up to 250°C when using the 3D printing
module, please be careful.
■
Please DO NOT operate or turn off Dobot Magician when burning firmware, to avoid ma-
chine damage.
4 Disposal
This symbol must appear on any electrical and electronic equipment placed on
the EU market. This symbol indicates that this device should not be disposed of
as unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-
back of waste. Conrad provides the following return options free of charge (more details on
our website):
■
in our Conrad offices
■
at the Conrad collection points
■
at the collection points of public waste management authorities or the collection points
set up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply
in countries outside of Germany.
5 Technical data
5.1 Power supply
Mains power supply........................ 100 - 240 V/AC, 50/60 Hz
Input power supply ......................... 12 V/DC, 7 A
5.2 Wi-Fi module
Wi-Fi standard ................................ IEEE 802.11b/g/n (HT20)
Wi-Fi frequency .............................. 2.412 - 2.462 GHz
Wi-Fi range..................................... Indoor: 180 m
Outdoor: 310 m
Wi-Fi transmission power .............. 19.9 dBm @ 11b, 1 Mbps
19.9 dBm @ 11b, 11 Mbps
19.0 dBm @ 11g, 6 Mbps
17.0 dBm @ 11g, 54 Mbps
18.0 dBm @ 11n, HT20, MCS0
16.8 dBm @ 11n, HT20, MCS7
17.4 dBm @ 11n, HT40, MCS0
16.0 dBm @ 11n, HT40, MCS7
5.3 Bluetooth module
Wireless frequency band................ 2.402 - 2.480 GHz
Wireless range ............................... 100 m
Wireless transmission power ......... -14 dBm to +8dBm
5.4 Environment
Operating temperature .................. -10 to +60 °C
6 Declaration of Conformity (DOC)
*2899511_V1_0923_jh_ss_en 9007200251320715-2 I2/O1 en